I am stuck in bootloader mode after trying to update to tomal mobile 6.
The screen on Imate jasjar says USB at the top and V 1.01 at the bottom.
The mobile device center does not allow USB since I checked it off.
When I execute MTTY1.42 usb is not given as an option.
When I execute MTTY 0.01 I get USB as an option However when I click on it I get the message "USB port cannot open"
By the way my screen says serial originally and then USB when I connect to my usb port.
I assume that if my screen says either serial or usb that it is in boot loader mode.
This is the second time that I had this problem after trying to update using Ranju's mobile 6 upgrade.
However the first time I was able to recover by starting with the MTTY 1.42 execution
Mobile device center suggests Vista. Most people would not dare these things without using XP. Suggest you do the same and disable activesync USB connection option before using MTTY
that is my next move. Go tto a computer with XP. although I was able to execute MTTY before this on my 64 bit vista computer.
Both my home computers run Vista 32 or 64.
Could there be a physical connection problem with my USB even if serial changes to USB when I plug my device into the USB port?
It is like I have apart USB connection but not complete. Or is there a software problem in the device with the part that handles the USB port? If so is there a way out?
If your device changes from serial to usb then you can start the upgrade... 8.5 seems to be the best so for with my experience..
Are you aware that I have a non background lit screen? That the device charge light does not come on? That it does not respond to soft reset?
It only reacts to hard reset and to the insertion of the USB cable?
When I try to run MTTY which I thought that I was supposed to to clear something I get the message that it cannot find a USB port.
Given this state can I do the upgrade that you suggested? or are you assuming that my imate jasjar is fully functioning
what do you mean by .......8.5 upgrade
Okay thats sounds good so far, i have been researching about that problem you have. when the serial changes to USB thats good, it means you are ready to run the update just ignore the recognition of the usb pop up message. did you down load the 8,5 Tomal's? if so run it i will do the same this side, i have been testing the 8.71 it tereble do not use it Tomal must try to put some time on it because he forgot some of impotant features. if the device shows usb then no need for MTTY. you just run the update rom. let us know what happens. Its normal that the back light is of just upgrade. Here is the link for the 8.5 upgrade screen shots; http://forum.xda-developers.com/showthread.php?t=454906 The download link; http://vidmes.com/xda/Uni/ROMs/Tomal...WM61_20764.exe
Looks like the download link will not work just scroll down on this link and download the special build rom. (window Mobile 6.1 V8.5 Tomal) http://forum.xda-developers.com/showthread.php?t=454906
Is your memory card slot in use? Remove memory card prior to using mtty or boot loader mode.
Yes the storage card is out
the sim card is out
the device is connected to the pc
the screen on the device shows USB
I run tomal version 8.5
I get the message
error CEROM update error
then I follow the recovery instructions
on recovery I get
RUU has stopped working
eroor 101 connection error
note
someone says
"U must remove the Memory card b4 upgrade, (Very impotant)"
Does that make sense
My problems started with
I had the crossbow Mobile on the system before.
I did a system restore
then tried install tomal 8.5
and from there things went off the cliff
I am now going to try things on a XP loaded computer as a last resort
swiching to my office computer and with active sync I was able to install TOML 8.5
Problem was with vista apparently
Mtty Help me Please..
Guys,
Please help me, every time I try to use mtty, it always like this attachment. What should I do, I allready follow the instruction, but still the same.
I would try on an XP computer
I did it on XP computer.
orb3000 said:
I would try on an XP computer
Click to expand...
Click to collapse
make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
indrastrid said:
make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?
Click to expand...
Click to collapse
irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
Now, there are only two things...
1. USB Sync driver in your PC is not functioning correctly
2. You have physical problem in USB port at your device
just my two cents.
irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
set your uni in bootloader i.e. press power button + backlight and reset using your stylus.
make sure you have disabled USB connections in AS
my two cents
Related
Whenever I try to flash HadSPL Windows pops up saying it's installing some driver and then says it has finished installing and the hardware is ready to be used, but then the progress bar just sits at 0%, I believe this has to do with the driver on my system for when my Kaiser is in flash mode, can anyone point me to the correct driver?
HyoImowano said:
Whenever I try to flash HadSPL Windows pops up saying it's installing some driver and then says it has finished installing and the hardware is ready to be used, but then the progress bar just sits at 0%, I believe this has to do with the driver on my system for when my Kaiser is in flash mode, can anyone point me to the correct driver?
Click to expand...
Click to collapse
As long as the correct version of ActiveSync/WMDC (depending on your OS) is installed, Windows will have the required drivers for "HTC USB SYNC" or however it shows up in device manager.
I have ActiveSync 4.5 installed on Windows XP, I've tried uninstalling, re-installing, re-starting, uninstalling drivers, re-booting, the whole shebang, but my device still just sits at 0% when flashing.
HyoImowano said:
I have ActiveSync 4.5 installed on Windows XP, I've tried uninstalling, re-installing, re-starting, uninstalling drivers, re-booting, the whole shebang, but my device still just sits at 0% when flashing.
Click to expand...
Click to collapse
Which version of JumpSPL/SSPL are you using? Also, try a different USB port.
Did you perform step 6 in the instructions on the second post
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
http://forum.xda-developers.com/showthread.php?t=396922
I exactly know the problem and the solution
While flashing remove all other USB devices(e.g. external harddrive, flashdrive) remove all USB devices other than your kaiser.
Hope that helps,
Regards
this might help in some cases if it was power issue..but in the case descibed in this thread i will agree that our friend must try different usb (the one at the back of your notebook/pc) not at side or front, use the one fed from motherboard...
also try to
uninstall and reinstall active sync
put your device on bootloader and plug usb (install the driver)
perform hardspl
perform flashing
best luck
hardik119 said:
I exactly know the problem and the solution
While flashing remove all other USB devices(e.g. external harddrive, flashdrive) remove all USB devices other than your kaiser.
Hope that helps,
Regards
Click to expand...
Click to collapse
Got it to work, thank you all very very very much for your help, it's greatly appreciated!
Hi guys,
I've just installed the Windows 7 ultimate RC on my PC and am now unable to sync my Raphael. I've installed Windows Mobile Device Center, but when I plug in my phone I get a message saying 'USB Device not recognized'.
I've tried both the stock rom and the Energy 3.0 ROM.
Anyone experiencing this also? Any solutions?
Thanks!
Same problem. But I couldnt even install the WDC? Which version did you install?
Weird
I'm using Windows 7 RC 1 (build 7100) and it works flawlessly with my TP. Installed WMDC 6.1 without difficulties.
PROBLEM FIXED for me
zonez said:
Hi guys,
I've just installed the Windows 7 ultimate RC on my PC and am now unable to sync my Raphael. I've installed Windows Mobile Device Center, but when I plug in my phone I get a message saying 'USB Device not recognized'.
I've tried both the stock rom and the Energy 3.0 ROM.
Anyone experiencing this also? Any solutions?
Thanks!
Click to expand...
Click to collapse
Try deleting this via regedit
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SQMClient\Windows\DisabledSessions
I'm using Windows 7 build 7077 and everything is going fine
Could you specify as to whether that key is located in Windows 7 or your phones OS?
brycestejskal said:
Could you specify as to whether that key is located in Windows 7 or your phones OS?
Click to expand...
Click to collapse
Sorry.In Windows 7
uh oh. i'm thinking of wiping vista from my machine and just using rc1. should i hold off on doing this?
Happened to me not 5min ago
1. Find the device in “Device manager” and remove it
2. Re-Plug in the device
3. A windows should try to install the software (Little popup in the task bar)
4. Click on it when it fails and tell it to check windows update to find drivers
I just installed RC1 last night. TP syncing just fine.
running windows 7...wmdc installed fine...
IF YOU ARE HAVING PROBLEMS SYNCHING!!
make sure to go into your phone settings
-go to connections
-go to usb to pc
-uncheck enable advanced network functionality
k thanks for the help guys, can't wait to get rc installed!
Thanks for the replies!
I tried all suggestions posted here, but none work.
The funny thing is that even when I put my phone in USB Drive mode, it still isn't recognized.
Updating the driver through windows update still results in 'An unknown device, your drivers are up to date'.
Syncing works without problems on my WindowsXP laptop..
The Muffin Man said:
Happened to me not 5min ago
1. Find the device in “Device manager” and remove it
2. Re-Plug in the device
3. A windows should try to install the software (Little popup in the task bar)
4. Click on it when it fails and tell it to check windows update to find drivers
Click to expand...
Click to collapse
This really worded for me. I installed Windows 7 the first day it was available and I was never able to figure it out how to make it worked until today. Thank you "The Muffin Man"
Running windows 7 RC and first few days when plugged phone in nothing happened. Was in no rush to get sync working as dual booting with Vista and was just plugging to charge phone. Other day I got a prompt to install device centre 6.1 and never done anything to initiate this. Wonder if an auto update may have caused this?
Works perfectly for me and tried with both Energy 3.0 and Elite RC4 (WM6.1 and WM6.5 ROMS).
In Vista atm so don't have W7 build number to hand.
I had a similar issue a few weeks back on my xp rig. Turns out I just needed to re seat my micro sd card, worked instantly.
nhshah7 said:
uh oh. i'm thinking of wiping vista from my machine and just using rc1. should i hold off on doing this?
Click to expand...
Click to collapse
go for it.. everything works great.. love the device support! plug in ur printer and thats pritty much it
Uninstall the "Windows Mobile Device Center" in your Control Panel, and plug your phone in again
Well i'm one step closer to fixing this..
I went into my bios and disabled USB2 (switching back to USB1).
After reboot my device was recognized and synced without problems.
As soon as I enabled USB2 again the device was undetectable again, even though Legacy USB support was enabled.
All other USB devices work, both in USB2 as USB1 mode.
Needless to say I don't want to run in USB1 mode.
Since I didn't have any of these problems with WinXP I assume it's a windows 7 issue.. Anyone knows where I can report this?
zonez said:
Well i'm one step closer to fixing this..
I went into my bios and disabled USB2 (switching back to USB1).
After reboot my device was recognized and synced without problems.
As soon as I enabled USB2 again the device was undetectable again, even though Legacy USB support was enabled.
All other USB devices work, both in USB2 as USB1 mode.
Needless to say I don't want to run in USB1 mode.
Since I didn't have any of these problems with WinXP I assume it's a windows 7 issue.. Anyone knows where I can report this?
Click to expand...
Click to collapse
Sounds like a driver support issue with your USB device (Motherboard).
I just installed WMDC and it worked without any problems.
Hi I Have Uni And Have Tomal v9 - Using Windows XP To Flash. Later I Use Windows Vista To Flash Tomal v10 I Did Not Download The Driver And Now It Is Stuck On BootLoader. The PC Know The HardWare. Please Help.
Hope this helps
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
Also have a look here to learn how to flash in vista and more usefull stuff
http://forum.xda-developers.com/showthread.php?t=567017
Thanks. Orb3000.
No prob, hope it helped
didnt help me
(MAKE SURE NOT TO USE A USB HUB).
didnt get this
and usb does not show in drop down menu (((
wasimlhr said:
(MAKE SURE NOT TO USE A USB HUB).
didnt get this
and usb does not show in drop down menu (((
Click to expand...
Click to collapse
it means yu hav to connect yur uni directly to the pc usb port, not through a hub, to avoid unwarranted disconnection. it is just a precaution and does not necessarily mean that flashing cannot be done through a hub.
as to the second query, if the mtty process is what you meant, be sure to disable usb in the activesync connection setting in order for usb prompt to appear.. cheers...
Not workign
If you are on windows 7 and are struggling with MTTY not showing USB use this - forum.xda-developers.com/showthread.php?t=540290
I think the most important things are the drivers.
Good luck
hi, im a new user and i have a problem connecting my spv c600 to my pc(windows xp)via usb. every time i try to connect my device the pc detects at first but then says"a problem occurred during installation your new hardware might not work properly" i have activesync 4.5 installed but it does not detect. i was wondering if there is a free driver i could download to sort this problem .please i need your help because i want to upgrade the rom
Windows Mobile devices are connected either via RNDIS or Serial over USB. Usually the decice is in the mode to connect over RNDIS, but when the drivers are missing on the PC they must be installed there. Look for generic RNDIS drivers on windows XP. You could also try to switch the device to Serial over USB mode. This hides in a something like "enhanced functionality" on the USB connection. On is "RNDIS" while off is "Serial" mode.
where can this "enhanced functionality" be found, on the device or on the pc, please guide me i'm kind of new on this things
It is on the phone, probably somewhere in the settings menu. No clue about the menu on your phone as I use a cooked WM6 ROM. Possibly it is even only hidden in the registry somewhere. You will have to search XDA for this a little yourself - I cannot guide you through this.
thanx for yor help
HI all, I seem to have a problem getting my laptop (ubuntu 12.04) to recognize my phone as storage when connected via USB. Here's what happened. I have already enabled USB debugging and USB debugging notify. When I plugged the phone to my laptop I got the usual message on the screen of my phone an when I clicked on it there were 2 tick boxes: one to recognize the phone as camera (that by the way worked) and the other one that recognized the phone as storage: when ticked nothing happened on my laptop, so I unticked both and now that bloody message is not coming up anymore on my phone, I only got one which says "USB debugging connected". ANy idea?
thanks
Disable the USB debugging... It's not needed for storage connection.
Sent from my One using XDA Premium 4 mobile app
HI thanks, ok fair enough but somehow I seem to have messed up with it and I would like to fix it if I can: I can't get the usb debugging mode message up when I connect the phone and the laptop doesn't recognize it as storage, not only ubuntu but even windows! could it be a matter of drivers? If so where can I get them from?
thanks
Menu>Storage>*menu on the upper right corner*>USB computer connection>*check box MTP/PTP*
happygolucky919 said:
Menu>Storage>*menu on the upper right corner*>USB computer connection>*check box MTP/PTP*
Click to expand...
Click to collapse
Thanks. When I connect the device as PTP it gets connected but when I do it as MTP , computer shows the error that drivers are not installed.
I'm having a similar problem on my phone, there is no option to change USB computer connection, so phone not regonised when plugged into PC? Any ideas?
MTP is a proprietary and modern protocol, older or open source OS's will not support it out of the box. You will need the relevant drivers, not sure how to do it on older version of Ubuntu, may be worth looking in their forums (support is included in new version in the proprietary driver bundle). There are no drivers for Windows XP, but you can get them for Windows 7, I'll dig out the guide I have bookmarked somewhere.
IIIIkoolaidIIII said:
MTP is a proprietary and modern protocol, older or open source OS's will not support it out of the box. You will need the relevant drivers, not sure how to do it on older version of Ubuntu, may be worth looking in their forums (support is included in new version in the proprietary driver bundle). There are no drivers for Windows XP, but you can get them for Windows 7, I'll dig out the guide I have bookmarked somewhere.
Click to expand...
Click to collapse
Thanks. That would be of great help.
Dush123 said:
Thanks. That would be of great help.
Click to expand...
Click to collapse
Here are the three guides I have bookmarked relating to MTP, I think the first from Tom's Hardware should fix (download is in 3rd post).
http://www.tomshardware.co.uk/forum/50119-63-devices-working
http://forum.xda-developers.com/showthread.php?t=2390296
http://forum.xda-developers.com/showthread.php?t=2391236
Hope these help.
B
---------- Post added at 09:22 AM ---------- Previous post was at 09:21 AM ----------
Oh yeah the other thing I didn't mention is MTP honors your phones security, so if you have a secure lock it won't show up initially until screen is on and device is unlocked.
Same issue, no options under USB computer connection !
boringfrog said:
I'm having a similar problem on my phone, there is no option to change USB computer connection, so phone not regonised when plugged into PC? Any ideas?
Click to expand...
Click to collapse
Hi, boringfrog,
were you able to get the issue resolved ?
After the phone upgraded from 12.0-YNG1TAS17L to 12.0-YNG1TAS2I3, i am seeing the similar issue, my phone will only charge on a Laptop, i tried different cables, 2 laptops, uninstalled and re-installed drivers, nothing works, i did a dirty flash back to 12.0-YNG1TAS17L the issue still exists, i tried enabling and disabling ADB debugging etc...
Under storage options , under the three dots on the right i see the USB computer connection, upon hitting it , nothing happens, the storage page just refreshes... no options to mount as MTP....
Please help need to copy the data from phone to PC...
mkhanemkay said:
Hi, boringfrog,
were you able to get the issue resolved ?
After the phone upgraded from 12.0-YNG1TAS17L to 12.0-YNG1TAS2I3, i am seeing the similar issue, my phone will only charge on a Laptop, i tried different cables, 2 laptops, uninstalled and re-installed drivers, nothing works, i did a dirty flash back to 12.0-YNG1TAS17L the issue still exists, i tried enabling and disabling ADB debugging etc...
Under storage options , under the three dots on the right i see the USB computer connection, upon hitting it , nothing happens, the storage page just refreshes... no options to mount as MTP....
Please help need to copy the data from phone to PC...
Click to expand...
Click to collapse
Sorry it was a friends phone so I just returned it to him after try a few attempts. Can you not put your data into the cloud then you can access it on your PC? Good luck.
PC not recognizing OnePlus 2 after update to Oxigen 3.0.1
What seems to solve the problem is to pull down the notifications bar, which shows one notification which gives you multiple options for the USB. Please choose the file download option(usually the second option). Your OPT will show up on the PC.
Thanks and regards to all.