Related
Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve
I've got the same problem. I can't connect via AS:/
I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.
Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve
It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.
Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve
Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?
Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.
Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.
This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?
Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck
Can You Tried Different Usb Cable :d
i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us
I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.
I have a strange problem with a HTC Touch PRO. Here is my problem:
- I insert the USB cable and the phone asks if I want to use mass storage or activesync
-the phone shows a connection on the screen
-The PC is not sensing anything, the activesync is not connected.
I think this problem appeared after I used a wrong usb cable...
Anyone knows anything what to try? or this is a hardware problem?
Did you select ACTIVESYNC?
There are 2 modes this phone can do..
1) Standard ActiveSYNC or
2) AS a MASS STORAGE DEVICE -like a flash drive...
You have to select ActiveSYNC to actually SYNC software/calendar, else it will show up as just another drive to drag/drop files..
Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?
laseru said:
Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?
Click to expand...
Click to collapse
The problem is likely with your operating system on your pc.
You can try things like, un-installing the HTC usb driver in device manager.
Check your firewall.
- allow activesync for trusted
- I know for ZoneAlarm you have to go to the adapters section and set the ipaddress (a new one is created when your phone is hooked up via USB) to be trusted.
If that doesn't fix issue perhaps its a corrupt install of ActiveSync. Try uninstalling and reinstalling.
laseru said:
Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?
Click to expand...
Click to collapse
I've had this happen to me. I've got so many USB to mini-USB cables and they are not all alike.
Sometimes, it would work and sometimes activesync would not recognize it.
CHANGE YOUR CABLE to another. Hopefully, you've labeled the original cable that came with the phone..
(also, look at the mini cable where it plugs into your phone. Make sure there are no loose pins and/or verify that the 'plug' is level.
Try a different USB port
Try unchecking "use advanced network configuration" in Async settings on the phone. Some computers (for various reasons) have a hard time communicating with the phone when it's configured as a network device - unchecking this will often allow Async to find and connect to the phone, at the expense of some other functionality.
coincendentally i am having the same exact issue, it started last night.
i have tried 3 different cords, on all 3 usb ports on my computer. same thing the phone asks what kind of connection i want whether i select disk drive ofr active sync noting happens. whats weird is that the phone is charging when its connected however the computer is not seeing it at all.
i have tried all the recommendations in this thread but nothing is working. anymore help would be greatly apprciated!
Me too I have tryed everything but none is working.
I think that this a hardware problem, and the problem started to happen after i used a non HTC cable, bad quality. I think some kind of controller is dead. So i started to live with that
When I connteced to the PC via USB, my TP also asked me how to connect (AS or as disc). But suddenly it doesn't ask anymore. I had to deactivate "advanced network configuration" to conntect to AS.
The checkbox "ask each time USB connects" is activated.
What can I do that the phone asks again when I connect it?
Thx.
I have the same thing going on... suddenly a few days ago my fuze only charges when I plug it in the desktop with a usb cable... I re-flashed and it worked about halfway through a sync and then started again... I've tried different cables... uninstalled all of the usb drivers, and reinstalled then updated them... Disconnected the power supply... tried every setting on my phone, and in windows.... I've even uninstalled the last batch of windows updates that came out last week... nothing seems to work...
really simple solution.
decheck advanced network config. plug in cable wait till you see usb connected. a small box. after that choose for example activesync
internet share
This happened to me last night and I figured out that after you toggle your internet sharing you can sync up again. Idk why it works out like that but it worked for me.
This sound reasonable, because the last thing I did before was selecting the "internet sharing" option in the menu when you connect to USB.
But what do you mean with "toggle your internet sharing"? Can you please describe it.
Thx.
try this
okay - first see if you're getting an active connection with your pc , not from the network connections window, but by running mymobiler. I was getting a connection through mymobiler, but active sync wasn't recognizing the device. If mymobiler works, Call your phone. it will drop your connection with mymobiler when you answer the call. then hang up the phone call. (all the while leaving your cable plugged into your phone. When the call has been disconnected your activesync will recognize the connection and sync up again. I don't know why this works, but I've been able to duplicate the results several times.
Same htc ****+ wm. Bought an iphone 3g. Everything must be tuned in windows mobile! It doesn't work how it should!
None of this seems to be working... I've even flashed new roms and it stops working halfway through the sync... it doesn't even appear as though windows recognizes the device... it makes no noise or pop-up when I connect it...
Still charges though... Don't know what is going on...
Reinstall Mobile Device Manager!
modulusman said:
None of this seems to be working... I've even flashed new roms and it stops working halfway through the sync... it doesn't even appear as though windows recognizes the device... it makes no noise or pop-up when I connect it...
Still charges though... Don't know what is going on...
Click to expand...
Click to collapse
I've experienced this issue multiple times, as I use my TP to sync with many stations. The solution is way more simple than you think and it has nothing to do with cables!.
You probably use Win Vista so all you need is to uninstall "Windows Mobile Device Center", restart the PC and install a fresh copy from MS site.
http://www.microsoft.com/downloads/details.aspx?FamilyID=83D513EA-9DF9-4920-AF33-3A0E2E4E7BEB&displaylang=en
If you're on XP, do the same with the Active sync solution for XP.
Good luck!
yeah this happens to me every now and then. the advanced network configuration option really helps, but sometimes i just need to plugin/unplug the usb cable from teh phone/cable or cable/computer a couple more timesbefore it picks it up...
goodluck!
hello my htc touch pro does not connect with activesync but the phone works perfectly
usb?
bluetooth?
tried other usb ports if usb ?
tried another computer?
yes i have tryed all tha no differance it will not work with active synce i tryed a hard restaand all what i could think of
1. check the manual
2. get newest activesync from microsoft
3. check settings (connection - usb to pc)
4. keep in mind, that it does not work with vista (at least it's not that easy)
5. if all that does not help, google or post again... we should find a solution
Also, do you synch another phone on this same computer? XP/winmo hasn't previously allowed synching two mobile devices. However i see they are offering a mobile "suite" that will help with this. (at winmo site).
When i first got my fuze i went thru this very same thing. Because my kaiser was already being used on the same computer.
yeah my kasier syncs fine
You should backup your data and upgrade your ROM. Which one are you using now? My experiences says it may solve a lot of troubles...
had this same problem a while back. make sure you don't have activesync on your computer looking for the old partnership and try going to settings>connections(tab)>USB to PC and unchecking "enable advanced network functionality" or if that is unchecked, try re-checking it.
I haven't plugged my fuze into any PC's for a couple of months - last time I did it was with a Windows 7 machine and it worked fine....
Well - now I'm trying to get the thing to sync with an XP machine. When I plug it into the usb, I see the fuze is charging - but activesync never comes up and nothing on the pc indicates that is saw me do this.
I've tried with 3 different XP machines here today - and none of them realize I've plugged anything in when I connect my fuze?
Soo...must be something with my fuze? Anyone have any ideas?
Only thing I saw was in settings/connections/usb to pc
there is an option for "enable advanced network functionality" - which I have disabled.
FYI I'm running WM 6.5 on it....
All previous reports of this issue ended with bad USB port on Fuze but you may want to search and read a couple of the threads first.
Interesting.
I can't seem to find any of these treads - can you point me to any?
Seems rather odd that if the port was bad that the phone would still charge though....
Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Here is one recent thread and I know I saw another that mentioned the device would charge but not sync.
Here are many more threads regarding AS issues.
Bruce Inman said:
Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Click to expand...
Click to collapse
I'm using WM 6.5 - and there I see:
settings/connections/USBtoPC
..that brings up a window which has settings on the behavior of the device when you connect it to a pc via USB. The options are to a) ActiveSync or b) DiskDrive
If you select a) ActiveSync you can "enable advanced network functionality"
There is also an option at the bottom that will cause it to ask which connection type to use when you connect.
I've tried all possible combinations - my pc does nothing when I connect, but I *do* see the fuze charging...freakn strange!
Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.
Bruce Inman said:
Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.
Click to expand...
Click to collapse
MyMobiler uses activesync to connect so that won't really be of any help at this point...
I was considering doing a hard-reset - but MAN I have about 140 apps installed and configured so I really hate doing that. What would be nice is if I could just find the driver and try that.
So that I suppose is my next question - anyone got the driver? hahaha
I use Pocket Controller which can use an IP address instead, I assumed MyMoblier was similar.
Copy the enclosed .dll to your windows directory using something like total commander because it is a cooked in system file. It still may not allow it though.
You should also look into Sashimi restoral program, as it is not uncommon to have to hard reset occassionally.
Good luck!
Is a firewall blocking it?
Each time I want to sync my Fuze, I have to disable my firewall. For some reason, even when I open the correct ports, my Fuze will not sync to Windows Mobile Device Center on my Vista Ultimate (32-bit) laptop.
Once it connects, I can turn the firewall back on and everything works fine. New and changed items will continue to sync until the Fuze is disconnected from laptop.
You may have already checked this and/or things may be different with XP and AS, but since I didn't specifically see it in the post, I thought I would throw it out there.
Bad cable???
I decided to try a different mini-usb cable and it worked.
Here is what is strange though - the bad cable:
1. Still charges the phone when connected to a PC
2. Works fine with my external 500gig USB hard drive (which also is powered via the cable)
3. ...but no computers see the phone with this cable - or see it as a storage device.
Because of #1 and #2 above - I assumed the cable must be good. I had another cable so I figured I'd give it a shot - and sure enough with this cable it works with all the computers.
I guess there must be one bad pin or something with the cable - or something??? Guess it must use different ones than the external hard-drive apparently.
Oh well - at least it works and rather it be a $2 cable than my $200 phone...hahaha
Thanks everyone for the suggestions....
For what it's worth if anyone stumbles across this post in the future, I had a similar issue happen where it would bring up the usb menu on my fuze when you plug it in, but the computer wouldn't see it.
I had recently swapped the display/touchscreen, and it was one of the strips of metal ground/shielding tape inside the thing being mispositioned that did it.
Put it back together with everything in the right place and boom! works.
If you've taken the phone apart, those pieces of shielding tape are very important to get back exactly like they were, I've also seen lcd issues from it.
It's easier if I just post a link to the thread over at smartappsworld so I'm not stuck re-writing it all. http://smartappsworld.com/thread-t...-getting-error-692-hardware-failure-in-modem
I still have not been able to resolve these issues. Tethering worked without problems on my Q9M, but on the TP2 it gives me error 692 -There was a hardware failure in the modem - . Internet sharing isnt cooperating either. New hardware wizard in XP pops up for Generic RNDIS device. When I tried to feed it some drivers for Internet Sharing (pulled by another xda member in another thread here somewhere), XP gives me some bogus error about a missing entry in one of the .inf files that I pointed it towards. It doesnt specify which file, then it closes and there is a big yellow ( ! ) over Internet Sharing device in network devices (Driver not installed).
Thats a quick run through of the issues I'm dealing with. I really need this working as this is my only way to connect my PC to the internet. I live in boonie land where cable is nowhere in my neighborhood and dsl is too far to connect.
Yes I searched. I spent a great deal of time going through xda forums and Google... before I decided to post here. Thanks for anyones help in advance.
T.C.
I have not had a problem tethering my tp2 with verizon using Win XP Pro x64, or XP home x86.
The way that works for me is:
Run the internet sharing program, Not the VZW access manager crap.
Tell it to connect
After it connects, then plug in usb from pc to phone
The pc recognizes it as another network connection
It gets its IPs and all no problems.
Open up your choice of browser and off you go.
I have never had to install drivers to do any of this, and also it doesnt use active sync when doing it this way.
hope this helps.
I pulled the internet sharing program out of the Windows folder (made a shortcut ). The problem is when I connect to the PC. The install new hardware wizard comes up for Generic RNDIS device. This is after I clicked "Connect" in IS. I have clicked cancel , then it says install failed, your new hardware may not work properly. IS disconnects and Activesync starts syncing. I tried it the first way , letting AS sync once then turning IS on, same problem.
I dont use VZ Access Manager. I was forced to uninstall that and Activesync when suddenly the PC wouldnt recognize anything while the phone was plugged in. After that, the phones internet wouldn't work either so I then had to restore the phone to factory defaults via a hard reset. After resetting, I found that 228 wouldn't program the phone. The next day I nearly took it in to VZW. tried 228 again and it worked finally. Got my phone internet back and I'm back to trying to get IS working. I didn't install VZAM, but I do have the USB driver installed.
Are there certain files that are needed on XP for this? I am still running 32bit XP Pro if that makes any difference. Service packs maybe? I'm up to the point where I'm about to go out and buy a WiFi card and try connecting it that way. Something Has to work here.
The generic RNDIS ( Remote Network Driver Interface Specification ) drivers are part of the ActiveSync install and are needed for TCP/IP between the PC and the phone.
Install ActiveSync.
Plug in the phone.
Don't cancel the New Hardware Found - let it install the drivers.
Set up a sync relationship with the PC if you like - not needed.
When you tell ICS to connect, it should drop any other connection to the PC (Hard Drive, Active Sync) and make the Windows connect sound. Then you should see the network negotiation icon in the System Tray as it sets up the internet sharing.
When I dont cancel New Hardware wizard, it doesn't find any drivers to install. This is if I let it search for drivers automatically, and after Activesync is installed. See what the problem is here? What should normally work, doesn't. Are there key files missing in the copy of Activesync that is included on the CD from VZW? What am I missing here? When I turn Internet sharing on, on the phone, it always says something like ''Check USB cable connection'' and it never changes. The hardware wizard never finds the drivers, and when I try to point it towards driver files, it says theres an entry missing and wont install.
Grr..if you read through the other thread link above, you know how long i have been trying to get it to work. Frustrating!!
Wallking HotSpots
THE-COPS said:
It's easier if I just post a link to the thread over at smartappsworld so I'm not stuck re-writing it all. http://smartappsworld.com/thread-t...-getting-error-692-hardware-failure-in-modem
I still have not been able to resolve these issues. Tethering worked without problems on my Q9M, but on the TP2 it gives me error 692 -There was a hardware failure in the modem - . Internet sharing isnt cooperating either. New hardware wizard in XP pops up for Generic RNDIS device. When I tried to feed it some drivers for Internet Sharing (pulled by another xda member in another thread here somewhere), XP gives me some bogus error about a missing entry in one of the .inf files that I pointed it towards. It doesnt specify which file, then it closes and there is a big yellow ( ! ) over Internet Sharing device in network devices (Driver not installed).
Thats a quick run through of the issues I'm dealing with. I really need this working as this is my only way to connect my PC to the internet. I live in boonie land where cable is nowhere in my neighborhood and dsl is too far to connect.
Yes I searched. I spent a great deal of time going through xda forums and Google... before I decided to post here. Thanks for anyones help in advance.
T.C.
Click to expand...
Click to collapse
I myself use WalkingHotSpots http://www.walkinghotspot.com/. It is 24.99 for a lifetime license and currently they allow you to use the license over and over when you upgrade your phone. I used it first when I had the Touch Pro and now I am using it with my TP2. It is a program that allows me to add up to 5 connections and use my TP2 as a Hotspot. Now of course it would requre you to have your TP2 connected and charging via wall outlet. But basically it will allow me to connect 3G using my WiFi. I just used it Tuesday night while at church to connect back to my business server and resolve some databases issues. My laptop was running at an excellent speed and I was online over 2 hours with no drop connections. The walking hotspot website says that it will not work with Verizon but I can personally say that it does. I do not have the Internet connection software installed on my TP2 so I am going all WiFi for my connection. I added a password and name for my Walking HotSpot so no random joe could just drive by and conect lol and I was up and running in about 10 minutes. They don't offer a free tiral but you can try it for 1 month for 6.99 and if it doesn't work you will not have wasted 25.00. Just choose to use it for a Touch Pro and you should be able to get the download. I have had it over a year now and it has come in very handy especially when I go home to visit Mom as she has no internet and walking hot spots runs my husband's laptop and mine without any issues. So whatever you ultimately do I hope you get it worked out
WMWifiRouter
I use WMWifiRouter on my phone for internet sharing. It works great. This may be an alternative for you.
http://www.wmwifirouter.com/
(the site appears to be down at the moment)
I just loaded a program called PdaNet and was really amazed at how easy it was to install. Hooked up on Verizon @ 2.4mbps - actually faster than my DSL!!!
I've only tried it a couple times but I recommend going to here http://www.junefabrics.com/pdanet/index.php and download a trial version.
WMWiFiRouter
I second the vote for WMWiFiRouter. I used it on my Mogul and now on my TP2 (both with Sprint) -- no issues whatsoever -- more importantly, no tethering fees.
For me now, when i use USB or Bluetooth over ICS, my browser has to go to 3g.vzwdun.com. It didn't use to do that before. How can I keep the device from reporting that I'm tethering...