Database Info

Possible Stupid Question. Lost USB connectivity.

Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve

I've got the same problem. I can't connect via AS:/

I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.

djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?

Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.

Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve

It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.

Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve

Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?

I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?

ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?

Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.

Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve

ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.

Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.

This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?

Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck

Can You Tried Different Usb Cable :d

i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us

I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.

Activesync won't recognize Raphael,...

hello everyone,
I cannot get Activesync to recognize my htc touch pro no matter what i do,... i've uninstalled and reinstalled shut everything off then on, followed all of MS's advice, and nothing works,...
Any suggestions,...? No problems connecting my tytn II and my hermes,...
thanks,
ek

Are you running any firewall software? If so, this is relevant to you.

start>>settings>>connections>>usbtopc>> un check the "enable advanced network functionality"

sorry attnoob, was trying for your quick fix, but it didn't work,... thanks anyway,... now will go to the firewall issues noted above, but i already opened the ports as per ms's recommendations in help,...
will try other suggestions and get back to you,...

ok, so allenh, read all the info at the link you sent me, and actually did all these things yesterday, but it didn't work,... also, something strange happens when i hook the device to the PC in that, the device immediately goes to the 'internet sharing' program you use when tethering, it establishes a connection with the internet, and there is a comments saying 'check usb cable connection' and this never happened with the tytn II,...
your help is appreciated,...
ek

Check the USB cable
It seems the USB cable the Tilt uses and the one the Raphael/Fuze use are different, If i use the cable that i usued with my tilt the computer would not recognize the Fuze it will charge it though, only if i use the usb cable that came with the Fuze it works fine.

Are you using the stock ROM or a cooked ROM. Some of the new cooked ROMS are having this problem.

Also, are you using Vista or XP. The problems seem to be with XP.

my fuze seems to also be having this issue... i can hear my laptop do the little noise saying something is attached but my phone never pops up with the screen anymore asking what i would like to do. sometimes i get lucky and it will randomly connect to active sync but would not give me any warning whether it was going to work or not.

btw, it didnt start doing this until i flashed NATF's v2.1 and also loaded a custom theme and toolbars and such.... it worked after i loaded NATF's rom, just randomly stopped at some point after that.

if you are putting on a new rom then put the phone in bootloader mode it worked for me

LostcauseZ06 said:
my fuze seems to also be having this issue... i can hear my laptop do the little noise saying something is attached but my phone never pops up with the screen anymore asking what i would like to do. sometimes i get lucky and it will randomly connect to active sync but would not give me any warning whether it was going to work or not.
Click to expand...
Click to collapse
My Fuze is doing this too, excep every single time. I can't get Activesync to work through USB. And I'm running the stock ROM. Internet Sharing automatically connects.

Okay, I set Internet Sharing to Bluetooth PAN (instead of USB), which kept it from automatically starting when I plugged in the USB. This let ActiveSync and the 'choose a connection type' startup on my Fuze and everything has been fine.

Try your PC Network settings
Hi,
I have the same problem recently. My AS does not want to recognize my Raphael. What I did was go to the network setting of the PC (Network Connections) and disable the 1394 adapter. Then my AS now can recognize my Raphael. The next unsolved thing is how to make the connection stable enough to make happen the syncing.
Drax

Hi, I had similar problem. Once upon a time the connection between my Touch Pro (WM6.5.3) and PC stopped working. Activesync did nothing and after a minute gave error message with troubleshoot guide. So I opened control panel ---> device manager (with mobile connected via USB), where I found "Windows mobile based device" between network adapters. I opened it and under it's advanced settings I found "network address" which was set to "unavailable". So I changed it to 192.168.2.2 and now it works again ;-)
Hope it helps someone ;-)

LG Incite CT810 - Problem with USB

So I got my shiny new LG Incite at Best Buy yesterday. I knew I was getting it a while ago, so I downloaded a bunch of games and apps to load it up with as soon as possible. I get home from the store, play around with it and let it charge for a while, then I try to connect it to my computer (After installing ActiveSync 4.5 from the included disk, as well as both of the USB drivers on the disk). Windows comes up with that "found new hardware" stuff and asks where to look for the driver to install. I tell it to look on the CD, as well as the directories where the USB drivers from the disk were installed. It looks like it's working at first, but then I get this error:
(Error: "The data is invalid.")
Then it gives me the message balloon about how there was an error during installation and my new hardware may not work properly, etc. Now when I go to Device Manager, a number of things showed up with that little yellow exclamation point that I'm pretty sure were not there before, but I could be wrong:
- IEEE 1394 Bus host controllers: VIA OHCI Compliant IEEE 1394 Host Controller
- Network Adapters: Unknown device, WAN miniport (L2TP), WAN miniport (Network Monitor), and Windows Mobile-based Device
- Ports (COM & LPT): Communications Port (COM1)
So I tried reinstalling the drivers from a link I found in a thread on these boards (after clicking uninstall for "Windows Mobile-based Device" and having it tell me that the device is necessary to boot up the computer), but the same thing keeps happening. I also tried having ActiveSync scan for devices, but it never finds anything (Just says that USB is "available").
Please help, I really want to start putting pictures, music, and all that good stuff on my brand new phone
(btw, I'm pretty sure the problem is with the software/drivers on the computer, because when I plug in the USB cable the phone starts to charge. Other than that, nothing happens on the phone.)

If at all possible, I would try using the phone with another computer. For quite some time I was only able to sync data with my laptop and not my desktop, so I knew it was a software issue and not the phone itself.

would say it's down to
dead activesync install and no uninstalling it is not enough one have
to remove all traces of it in registry too
and it could also be an issue with usb drviers for the motherboard

chad.pflughaupt said:
If at all possible, I would try using the phone with another computer. For quite some time I was only able to sync data with my laptop and not my desktop, so I knew it was a software issue and not the phone itself.
Click to expand...
Click to collapse
Well, I'm not going to have another computer until September at least, so I really want to get it working on this computer, but I guess I could test it out on a friend's pc to see if my computer is the problem.
Rudegar said:
would say it's down to
dead activesync install and no uninstalling it is not enough one have
to remove all traces of it in registry too
and it could also be an issue with usb drviers for the motherboard
Click to expand...
Click to collapse
Know of any links or tutorials that would tell me all of the registry entries I'd have to remove?

(Sorry for the double post, but no one was replying...)
So I found my bluetooth adapter for my PC, and after I installed the proper software I could connect to my phone no problem. After that, I just used the bluetooth adapter's software to transfer files to my phone via FTP. (ActiveSync still just sat there, even when I set my phone to sync with bluetooth instead of USB, and I allowed wireless connections in ActiveSync)
So I'm glad I can finally transfer files, but I still want to get USB working. No one has any ideas at all?

(Triple post... sorry)
Ok, something happened to the bluetooth drivers and software now. I turned my computer off for the night after using bluetooth to transfer files to my phone, but when I turned on my pc today and clicked the shortcut to start the bluetooth software, I got a message saying that the program the shortcut was linking to no longer existed. Sure enough, the folder was gone from my Program Files directory. Now, every time I try to reinstall it, I get an error 183 that installation was interrupted.
So now I'm back to having no means of transferring files to my phone.
Please, any suggestions at all will be helpful to me at this point. I'm at my wits end!

Any progress on this?
I have a similar problem. I think usb sync worked on my laptop at one point, but hasn't for at least a week.
I was able to fix the problem at least temporarily by disconnecting the device, deleting it from ActiveSync and reconnecting. ActiveSync happily added it back and resynced everything. Now I can install the new Xcite ROM.

Still nothing...
Now my computer doesn't do anything at all when I plug my phone in, not even make a noise or ask about drivers. My phone, however, still recognizes that it's plugged in.
At least I got bluetooth working again, but still, USB would be nice.
It's hard to believe that out of every member on this forum, no one has even the slightest idea of where to start...

Menu - settings - connections - USB to PC.
Uncheck Enable advanced ...
OK TO ALL AND READY

PC's don't see my Fuze no more?

I haven't plugged my fuze into any PC's for a couple of months - last time I did it was with a Windows 7 machine and it worked fine....
Well - now I'm trying to get the thing to sync with an XP machine. When I plug it into the usb, I see the fuze is charging - but activesync never comes up and nothing on the pc indicates that is saw me do this.
I've tried with 3 different XP machines here today - and none of them realize I've plugged anything in when I connect my fuze?
Soo...must be something with my fuze? Anyone have any ideas?
Only thing I saw was in settings/connections/usb to pc
there is an option for "enable advanced network functionality" - which I have disabled.
FYI I'm running WM 6.5 on it....

All previous reports of this issue ended with bad USB port on Fuze but you may want to search and read a couple of the threads first.

Interesting.
I can't seem to find any of these treads - can you point me to any?
Seems rather odd that if the port was bad that the phone would still charge though....

Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Here is one recent thread and I know I saw another that mentioned the device would charge but not sync.
Here are many more threads regarding AS issues.

Bruce Inman said:
Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Click to expand...
Click to collapse
I'm using WM 6.5 - and there I see:
settings/connections/USBtoPC
..that brings up a window which has settings on the behavior of the device when you connect it to a pc via USB. The options are to a) ActiveSync or b) DiskDrive
If you select a) ActiveSync you can "enable advanced network functionality"
There is also an option at the bottom that will cause it to ask which connection type to use when you connect.
I've tried all possible combinations - my pc does nothing when I connect, but I *do* see the fuze charging...freakn strange!

Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.

Bruce Inman said:
Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.
Click to expand...
Click to collapse
MyMobiler uses activesync to connect so that won't really be of any help at this point...
I was considering doing a hard-reset - but MAN I have about 140 apps installed and configured so I really hate doing that. What would be nice is if I could just find the driver and try that.
So that I suppose is my next question - anyone got the driver? hahaha

I use Pocket Controller which can use an IP address instead, I assumed MyMoblier was similar.
Copy the enclosed .dll to your windows directory using something like total commander because it is a cooked in system file. It still may not allow it though.
You should also look into Sashimi restoral program, as it is not uncommon to have to hard reset occassionally.
Good luck!

Is a firewall blocking it?
Each time I want to sync my Fuze, I have to disable my firewall. For some reason, even when I open the correct ports, my Fuze will not sync to Windows Mobile Device Center on my Vista Ultimate (32-bit) laptop.
Once it connects, I can turn the firewall back on and everything works fine. New and changed items will continue to sync until the Fuze is disconnected from laptop.
You may have already checked this and/or things may be different with XP and AS, but since I didn't specifically see it in the post, I thought I would throw it out there.

Bad cable???
I decided to try a different mini-usb cable and it worked.
Here is what is strange though - the bad cable:
1. Still charges the phone when connected to a PC
2. Works fine with my external 500gig USB hard drive (which also is powered via the cable)
3. ...but no computers see the phone with this cable - or see it as a storage device.
Because of #1 and #2 above - I assumed the cable must be good. I had another cable so I figured I'd give it a shot - and sure enough with this cable it works with all the computers.
I guess there must be one bad pin or something with the cable - or something??? Guess it must use different ones than the external hard-drive apparently.
Oh well - at least it works and rather it be a $2 cable than my $200 phone...hahaha
Thanks everyone for the suggestions....

For what it's worth if anyone stumbles across this post in the future, I had a similar issue happen where it would bring up the usb menu on my fuze when you plug it in, but the computer wouldn't see it.
I had recently swapped the display/touchscreen, and it was one of the strips of metal ground/shielding tape inside the thing being mispositioned that did it.
Put it back together with everything in the right place and boom! works.
If you've taken the phone apart, those pieces of shielding tape are very important to get back exactly like they were, I've also seen lcd issues from it.

Don't really know where to start.

I'll try and make this short. Phone charges fine on comp. or charger. Phone works some what fine. Bluetooth seems to be getting quieter and quieter, but thats not the main issue. WMDC isnt working. I uninstalled it and restarted, I downloaded a newer version, I even tried about 5 cables and still the computer isnt even seeing any device what so ever. I was going to task 29 and reflash but now I'm affraid if the phones not even being recognized. Is there some setting or something that happened to of gotten changed that block my phone other than the obvious -virus protection.
Using windows 7. Any help would be appreciated. Thank you.

Try a different usb port. I have had issues where the port I normally use for charging/syncing refuses to recognize my phone. I just use a different port and everything works fine. Even the first port starts working again. Windows 7 does seem to reinstall drivers again when I use switch ports, so patience is required.

Tried many different ports. Can't do a hard reset because : 1- I have some info and text that needs to be sync'd and : 2 my end button doesn't work anymore. Actually it was sticking so I kinda disconnected it. I would try to do a reflash from a SD card but like I said, I have stuff that I need sync'd and I'm not really sure if the phone just isnt going bad or software. I guess either way it wouldn't matter. Would like to learn how to sync with wifi.

I believe there is a wifi-sync method/program, but am not aware of the specifics. You could save your information to your sd card and simply use a usb reader to transfer the information that way. Or you can use the blutooth explorer on the phone to transfer to another blutooth device. Or I believe Google has a sync service so you can sync you information to your computers anytime and anywhere.
You can remap the "end" function to another key.
Your phone's usb port could have a cracked connection as mine disconnects while synced if I move the phone too much.

WMDC does not recognize the Mobile Device "MSW Vista and Later OS"
Try this procedure(s);
Settings, All Settings, Connections, USB Connections, clear the "Fast File Transfer" check mark under the Active Sync option. Restart the device and before connecting to the PC Double check to see if the the fast file transfer is still clear. then go ahead and try to see if your PC sees your device. Good Luck.
"ALEXANDER OF PERSIA"