Database Info

Possible Stupid Question. Lost USB connectivity.

Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve

I've got the same problem. I can't connect via AS:/

I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.

djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?

Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.

Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve

It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.

Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve

Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?

I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?

ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?

Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.

Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve

ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.

Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.

This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?

Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck

Can You Tried Different Usb Cable :d

i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us

I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.

Strange problem with USB connectivity

I have a strange problem with a HTC Touch PRO. Here is my problem:
- I insert the USB cable and the phone asks if I want to use mass storage or activesync
-the phone shows a connection on the screen
-The PC is not sensing anything, the activesync is not connected.
I think this problem appeared after I used a wrong usb cable...
Anyone knows anything what to try? or this is a hardware problem?

Did you select ACTIVESYNC?
There are 2 modes this phone can do..
1) Standard ActiveSYNC or
2) AS a MASS STORAGE DEVICE -like a flash drive...
You have to select ActiveSYNC to actually SYNC software/calendar, else it will show up as just another drive to drag/drop files..

Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?

laseru said:
Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?
Click to expand...
Click to collapse
The problem is likely with your operating system on your pc.
You can try things like, un-installing the HTC usb driver in device manager.

Check your firewall.
- allow activesync for trusted
- I know for ZoneAlarm you have to go to the adapters section and set the ipaddress (a new one is created when your phone is hooked up via USB) to be trusted.
If that doesn't fix issue perhaps its a corrupt install of ActiveSync. Try uninstalling and reinstalling.

laseru said:
Yes i did it in every way and the computer is not sensing the connection with the phone.
Anyone know what kinf of hardware is responsible for the connection with the pc?
Click to expand...
Click to collapse
I've had this happen to me. I've got so many USB to mini-USB cables and they are not all alike.
Sometimes, it would work and sometimes activesync would not recognize it.
CHANGE YOUR CABLE to another. Hopefully, you've labeled the original cable that came with the phone..
(also, look at the mini cable where it plugs into your phone. Make sure there are no loose pins and/or verify that the 'plug' is level.

Try a different USB port

Try unchecking "use advanced network configuration" in Async settings on the phone. Some computers (for various reasons) have a hard time communicating with the phone when it's configured as a network device - unchecking this will often allow Async to find and connect to the phone, at the expense of some other functionality.

coincendentally i am having the same exact issue, it started last night.
i have tried 3 different cords, on all 3 usb ports on my computer. same thing the phone asks what kind of connection i want whether i select disk drive ofr active sync noting happens. whats weird is that the phone is charging when its connected however the computer is not seeing it at all.
i have tried all the recommendations in this thread but nothing is working. anymore help would be greatly apprciated!

Me too I have tryed everything but none is working.
I think that this a hardware problem, and the problem started to happen after i used a non HTC cable, bad quality. I think some kind of controller is dead. So i started to live with that

When I connteced to the PC via USB, my TP also asked me how to connect (AS or as disc). But suddenly it doesn't ask anymore. I had to deactivate "advanced network configuration" to conntect to AS.
The checkbox "ask each time USB connects" is activated.
What can I do that the phone asks again when I connect it?
Thx.

I have the same thing going on... suddenly a few days ago my fuze only charges when I plug it in the desktop with a usb cable... I re-flashed and it worked about halfway through a sync and then started again... I've tried different cables... uninstalled all of the usb drivers, and reinstalled then updated them... Disconnected the power supply... tried every setting on my phone, and in windows.... I've even uninstalled the last batch of windows updates that came out last week... nothing seems to work...

really simple solution.
decheck advanced network config. plug in cable wait till you see usb connected. a small box. after that choose for example activesync

internet share
This happened to me last night and I figured out that after you toggle your internet sharing you can sync up again. Idk why it works out like that but it worked for me.

This sound reasonable, because the last thing I did before was selecting the "internet sharing" option in the menu when you connect to USB.
But what do you mean with "toggle your internet sharing"? Can you please describe it.
Thx.

try this
okay - first see if you're getting an active connection with your pc , not from the network connections window, but by running mymobiler. I was getting a connection through mymobiler, but active sync wasn't recognizing the device. If mymobiler works, Call your phone. it will drop your connection with mymobiler when you answer the call. then hang up the phone call. (all the while leaving your cable plugged into your phone. When the call has been disconnected your activesync will recognize the connection and sync up again. I don't know why this works, but I've been able to duplicate the results several times.

Same htc ****+ wm. Bought an iphone 3g. Everything must be tuned in windows mobile! It doesn't work how it should!

None of this seems to be working... I've even flashed new roms and it stops working halfway through the sync... it doesn't even appear as though windows recognizes the device... it makes no noise or pop-up when I connect it...
Still charges though... Don't know what is going on...

Reinstall Mobile Device Manager!
modulusman said:
None of this seems to be working... I've even flashed new roms and it stops working halfway through the sync... it doesn't even appear as though windows recognizes the device... it makes no noise or pop-up when I connect it...
Still charges though... Don't know what is going on...
Click to expand...
Click to collapse
I've experienced this issue multiple times, as I use my TP to sync with many stations. The solution is way more simple than you think and it has nothing to do with cables!.
You probably use Win Vista so all you need is to uninstall "Windows Mobile Device Center", restart the PC and install a fresh copy from MS site.
http://www.microsoft.com/downloads/details.aspx?FamilyID=83D513EA-9DF9-4920-AF33-3A0E2E4E7BEB&displaylang=en
If you're on XP, do the same with the Active sync solution for XP.
Good luck!

yeah this happens to me every now and then. the advanced network configuration option really helps, but sometimes i just need to plugin/unplug the usb cable from teh phone/cable or cable/computer a couple more timesbefore it picks it up...
goodluck!

More ActiveSync Problems... I'm desperate, PLEASE help.

Hi:
I have a Fuze I have been using for several months. At some point it stopped connecting via USB to Active Sync. I was still able to sync via bluetooth.
Since the official ATT ROM is about to be released I decided to troubleshoot the USB/ActiveSync problem.
Well, I checked all connections, deleted and reinstalled partnership, tried different cables, different USB ports, uninstalled and reinstalled ActiveSync, unchecked the advanced network functionality box, turned Firewall on and off. Other usb devices are working fine, and I am able to connect the phone as storage/file transfer, just not ActiveSync.
I have searched and searched, and tried everything I can find, but now after so much messing with it, I am unable to connect to ActiveSync at all. When I try to pair it via bluetooth to my phone ActiveSync doesn't even show up as a service anymore.
When I connect via usb, I get the same error unable to establish a connection, and it suggests I check my Firewall.
I have added ActiveSync to my Firewall etc..., as well as completely disabling my Firewall. Still nothing. I have tried all the steps suggested by ZoneAlarm.
I am using Windows XP, ZoneAlarm Security Suite 8.0.298.035.
ANY ideas would really, really be appreciated.
Thanks!

Activesync is one of M$'s WORST inventions! Before WM6, The only way to connect your computer was via activesync (there was no "drive" option that i knew of)
I HATE activsync, never have gotten it to work. Thank GOD Google sync is around, sync up my contacts and calendar over the air.
Honestly, I'd say avoid activsync at all costs. But one other option MAY be to create a new user account on your computer and try activsync with that user.
I could also say ditch windows for ubuntu, but i have yet to find any easy way to sync my Fuze with ubuntu

Hi Cass:
Thanks for the reply. Well creating a new user did enable me to once again sync via bluetooth, but still no luck with the usb connection
Is it possible to install a ROM update via bluetooth?
Thanks!

i am not expert and I have not had that problem wth my fuze, but have you tried doing a hard reset?

cincy1020 said:
Hi:
I have a Fuze I have been using for several months. At some point it stopped connecting via USB to Active Sync. I was still able to sync via bluetooth.
Since the official ATT ROM is about to be released I decided to troubleshoot the USB/ActiveSync problem.
Well, I checked all connections, deleted and reinstalled partnership, tried different cables, different USB ports, uninstalled and reinstalled ActiveSync, unchecked the advanced network functionality box, turned Firewall on and off. Other usb devices are working fine, and I am able to connect the phone as storage/file transfer, just not ActiveSync.
I have searched and searched, and tried everything I can find, but now after so much messing with it, I am unable to connect to ActiveSync at all. When I try to pair it via bluetooth to my phone ActiveSync doesn't even show up as a service anymore.
When I connect via usb, I get the same error unable to establish a connection, and it suggests I check my Firewall.
I have added ActiveSync to my Firewall etc..., as well as completely disabling my Firewall. Still nothing. I have tried all the steps suggested by ZoneAlarm.
I am using Windows XP, ZoneAlarm Security Suite 8.0.298.035.
ANY ideas would really, really be appreciated.
Thanks!
Click to expand...
Click to collapse
uninstall activesync, reboot,make sure activesync files were deleted, reinstall activesync, turn the firewall off (for testing purposes), (turn off MS firewall service in services) and try to reconnect then.

Need a little more information in order to help you. Information that would help is:
- Version of Operating System Service Pack
- Version of Active Sync
- Anti-Virus software
In the interim; can I assume that these KB articles did not help?
http://support.microsoft.com/kb/915152/en-us
http://support.microsoft.com/kb/912240/en-us
I've run into similar issues with other USB devices; and the solution is usually one of two:
1) Too many USB device entries
When a device is not connected to the PC, it doesn't display in the Device Manager. To display those hidden devices, follow the steps in this KB article:
http://support.microsoft.com/kb/241257/en-us
Once the hidden devices are displayed (usually semi-transparent looking) you can right-click on each one and remove it. If you see any hidden devices with an Exclamation, you need to remove those as well.
For the moment, keep to USB related devices - in other words, don't go removal happy ... some hidden devices are meant to be there.
2) Driver Signing
It's also possible that you have a driver signing issue. You can temporarily disable driver signing by right-clicking on My Computer and selecting Properties ... the option is found on the Hardware tab.
Don't leave it permanently disabled; set it Warn, at the very least, to avoid malicious installation of Trojan or other similar programs.
HTH,

You don't need activesync to install a ROM from the computer. Hold the power, volume down button, and press the reset button with your stylus. This will take you into bootloader mode. Keep holding the buttons after pressing the reset button until the tricolor screen comes up. Then plug the phone into the computer. It should say "USB" at the bottom, which shows that it is connected to the computer. Then flash away.
You can try it out and let us know if it works. Just soft reset after you confirm it works.
You could also flash via SD card, but that's more work and requires unlocking phone.

Thank you all so much!
I have not been able to try any of your suggestions, because I had an unexpected work issue arise, but I will definitely try then within the next couple days, and report back here.
Thanks again!

I have problems syncing with WMDC and my Fuze. When it becomes persistent, I end the partnership, uninstall WMDC, and then reinstall it. It then works for a while.

studentjunk said:
You don't need activesync to install a ROM from the computer. Hold the power, volume down button, and press the reset button with your stylus. This will take you into bootloader mode. Keep holding the buttons after pressing the reset button until the tricolor screen comes up. Then plug the phone into the computer. It should say "USB" at the bottom, which shows that it is connected to the computer. Then flash away.
You can try it out and let us know if it works. Just soft reset after you confirm it works.
You could also flash via SD card, but that's more work and requires unlocking phone.
Click to expand...
Click to collapse
Junk:
You are my hero!! Your advice worked perfectly. I was able to update to the new ROM without using ActiveSync.
Thanks so much!!
And thanks to those of you who replied. I didn't try the other suggestions, since Junk's worked perfectly for me.

PC's don't see my Fuze no more?

I haven't plugged my fuze into any PC's for a couple of months - last time I did it was with a Windows 7 machine and it worked fine....
Well - now I'm trying to get the thing to sync with an XP machine. When I plug it into the usb, I see the fuze is charging - but activesync never comes up and nothing on the pc indicates that is saw me do this.
I've tried with 3 different XP machines here today - and none of them realize I've plugged anything in when I connect my fuze?
Soo...must be something with my fuze? Anyone have any ideas?
Only thing I saw was in settings/connections/usb to pc
there is an option for "enable advanced network functionality" - which I have disabled.
FYI I'm running WM 6.5 on it....

All previous reports of this issue ended with bad USB port on Fuze but you may want to search and read a couple of the threads first.

Interesting.
I can't seem to find any of these treads - can you point me to any?
Seems rather odd that if the port was bad that the phone would still charge though....

Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Here is one recent thread and I know I saw another that mentioned the device would charge but not sync.
Here are many more threads regarding AS issues.

Bruce Inman said:
Let me ask you this, you say that you changed your PC to USB settings to Enable Advanced network functionality, I thought this setting was in Active Sync. USB to PC setting should be to "enable faster data transmission". Have you played with both settings?
Click to expand...
Click to collapse
I'm using WM 6.5 - and there I see:
settings/connections/USBtoPC
..that brings up a window which has settings on the behavior of the device when you connect it to a pc via USB. The options are to a) ActiveSync or b) DiskDrive
If you select a) ActiveSync you can "enable advanced network functionality"
There is also an option at the bottom that will cause it to ask which connection type to use when you connect.
I've tried all possible combinations - my pc does nothing when I connect, but I *do* see the fuze charging...freakn strange!

Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.

Bruce Inman said:
Have you tried to connect through an emulator like MyMobiler?
Its most likely a driver issue on your phone.
Hate to say it but.....
If all else fails, Hard Reset, flash back to stock ROM (if you've flashed a cooked ROM) and this should restore the corrupt driver.
Click to expand...
Click to collapse
MyMobiler uses activesync to connect so that won't really be of any help at this point...
I was considering doing a hard-reset - but MAN I have about 140 apps installed and configured so I really hate doing that. What would be nice is if I could just find the driver and try that.
So that I suppose is my next question - anyone got the driver? hahaha

I use Pocket Controller which can use an IP address instead, I assumed MyMoblier was similar.
Copy the enclosed .dll to your windows directory using something like total commander because it is a cooked in system file. It still may not allow it though.
You should also look into Sashimi restoral program, as it is not uncommon to have to hard reset occassionally.
Good luck!

Is a firewall blocking it?
Each time I want to sync my Fuze, I have to disable my firewall. For some reason, even when I open the correct ports, my Fuze will not sync to Windows Mobile Device Center on my Vista Ultimate (32-bit) laptop.
Once it connects, I can turn the firewall back on and everything works fine. New and changed items will continue to sync until the Fuze is disconnected from laptop.
You may have already checked this and/or things may be different with XP and AS, but since I didn't specifically see it in the post, I thought I would throw it out there.

Bad cable???
I decided to try a different mini-usb cable and it worked.
Here is what is strange though - the bad cable:
1. Still charges the phone when connected to a PC
2. Works fine with my external 500gig USB hard drive (which also is powered via the cable)
3. ...but no computers see the phone with this cable - or see it as a storage device.
Because of #1 and #2 above - I assumed the cable must be good. I had another cable so I figured I'd give it a shot - and sure enough with this cable it works with all the computers.
I guess there must be one bad pin or something with the cable - or something??? Guess it must use different ones than the external hard-drive apparently.
Oh well - at least it works and rather it be a $2 cable than my $200 phone...hahaha
Thanks everyone for the suggestions....

For what it's worth if anyone stumbles across this post in the future, I had a similar issue happen where it would bring up the usb menu on my fuze when you plug it in, but the computer wouldn't see it.
I had recently swapped the display/touchscreen, and it was one of the strips of metal ground/shielding tape inside the thing being mispositioned that did it.
Put it back together with everything in the right place and boom! works.
If you've taken the phone apart, those pieces of shielding tape are very important to get back exactly like they were, I've also seen lcd issues from it.

Don't really know where to start.

I'll try and make this short. Phone charges fine on comp. or charger. Phone works some what fine. Bluetooth seems to be getting quieter and quieter, but thats not the main issue. WMDC isnt working. I uninstalled it and restarted, I downloaded a newer version, I even tried about 5 cables and still the computer isnt even seeing any device what so ever. I was going to task 29 and reflash but now I'm affraid if the phones not even being recognized. Is there some setting or something that happened to of gotten changed that block my phone other than the obvious -virus protection.
Using windows 7. Any help would be appreciated. Thank you.

Try a different usb port. I have had issues where the port I normally use for charging/syncing refuses to recognize my phone. I just use a different port and everything works fine. Even the first port starts working again. Windows 7 does seem to reinstall drivers again when I use switch ports, so patience is required.

Tried many different ports. Can't do a hard reset because : 1- I have some info and text that needs to be sync'd and : 2 my end button doesn't work anymore. Actually it was sticking so I kinda disconnected it. I would try to do a reflash from a SD card but like I said, I have stuff that I need sync'd and I'm not really sure if the phone just isnt going bad or software. I guess either way it wouldn't matter. Would like to learn how to sync with wifi.

I believe there is a wifi-sync method/program, but am not aware of the specifics. You could save your information to your sd card and simply use a usb reader to transfer the information that way. Or you can use the blutooth explorer on the phone to transfer to another blutooth device. Or I believe Google has a sync service so you can sync you information to your computers anytime and anywhere.
You can remap the "end" function to another key.
Your phone's usb port could have a cracked connection as mine disconnects while synced if I move the phone too much.

WMDC does not recognize the Mobile Device "MSW Vista and Later OS"
Try this procedure(s);
Settings, All Settings, Connections, USB Connections, clear the "Fast File Transfer" check mark under the Active Sync option. Restart the device and before connecting to the PC Double check to see if the the fast file transfer is still clear. then go ahead and try to see if your PC sees your device. Good Luck.
"ALEXANDER OF PERSIA"