[Q] hepl me with my ipaq 4700 - General Questions and Answers

yesterday when i tried to update the room in my ipaq 4700 I entered in bootloader mode but the installation of the new room fail then i tried to quit bootloader mode but nothing happens after three hours of doing this my batery run out of power but then I realized that my ipaq wasn't charging and now it seems to be death can you help me please

Related

IPAQ 6340 boot & phone problem

Hi all,
Once upon a day, i rebooted my ipaq 6340, after the progress indicator is on the end, it takes more then 1 hour! until the win mobile screen shows up.
My ipaq also behaves like this when doing a hard reset.
I can put the ipaq in bootloader mode, when i put it in the craddle it says USB BL, when i take it outside the craddle there still stands USB BL
The official rom update, doesn't work. After rebooting it hangs (again for + 1 hour) and the updater application does a timeout.
Unofficial rom updates (like the one in the sticky thread) also doesn't work. (The hosts pc screen stays at : veryfying the information on your ipaq pocket pc ... please wait)
Other things with this ipaq which also go wrong : if i try to activate the phone (via ipaq wireless, sim contact, mini tasktray above on the today screen etc), the ipaq locks up.
Any help, official patches, unoffical patches, programs to mod the rom by usb telnet or whatever, ideas, etc extremely appreciated.

[ HELP ] HP Ipaq 512 - Unable to go beyond HP Boot screen.

Hello,
I have a HP IPaq 512 its just over a year old but some time back it froze and I restarted the phone and now it wont go pass the HP Boot screen.
I have tried to hard reset the IPaq using the Center key and the red key but that didn’t work. I got the message for soft reset and got the conformations asking if I was sure… I said yes but again it froze at the HP logo Screen.
I am unable to flash the rom since it’s not recognized by my (WIN XP) pc as a USB device. (Since it doesn’t boot completely)
I have been to HP Service center and the cost they gave me to repair was more than double its buying price.
Could any one please help me this problem here please?

HELP PM300 S200 Rom Device Issue

Have S200 G3 in Tri Color screen that gets to 50% on ROM load before it starts shutting off n on. It does the same thing if it is plugged into a pc via usb cable w/ battery installed after a short period of time.
It does not turn off n on it it is simply sitting there w/ the battery installed. Only when it is plugged in w/ a USB.
Does some 1 have access to info on phone recovery via flash card and Rom that I can use.
If not steps on resolving the problem long enough to load a basic Rom on the unit.

[Q] iPaq 3630 ROM update failing at 98% no USB communication

I did an update withthe ROM and utility off the HP site which then came up with a message about lost comms on the USB port. I left ist sitting in the cradle connected for about an hour but nothing was happening so I unplugged it from my win7 machine and tried with an XP machine. Still no luck.
I have tried the reset, combinations of power contacts iTask and reset button and power calender iTask and reset but nothing changed, it still had a blue screen with no back light. I pulled the battery lead and the screen changed slightly but nothing else.
Any ideas how it can be resurected?
I have followed the instructions from forum.brighthand.com ipaq-h3600-h3900-series 273231-h3630-bricked and that has shown how to get the iPaq ready and what software to restart the process with (host11) but everything goes fine up to 98% when I get a message 'lost USB communications' and it stops.
Does this mean I have bad sectors in my ROM chip? How can I fix this?
Is there a linux ROM which would fit in less than 98% of 16 Mb?
Please help.

[Q] Galaxy 5 stuck in 'ramdump mode'

Hey guys
I couldn't get an answer to my question in any topic, so I decided to post here and ask for help.
I bought a Galaxy 5 from my neighbor and I didn't test it 'cause it was with the battery discharged.
I charged the battery to 100% I tried to turn on my galaxy.
But every time I try to turn on the smartphone, It get stuck on a screen with samsung logo and with the text: "Ramdump mode (arm9 mode)".
I just tested it in 4 computers but everytime I connect the phone to usb it just starts to charge the battery.
I can enter in download mode to put a stock rom on it, but it doesn't help me so much 'cause if my phone isn't recognized in the PC and in Odin, I can't do nothing.
So that's the situation: My smartphone isn't recognized by the computer (windows don't at least show any message about usb device connected). When I plug it in usb it just starts to charge.
So I'm asking for help.
Is there any way to put a bootable android in my microSD that starts automaticlly the installation when I turn on the phone ?
Thanks
Anyone haver a solution for this problem?

Categories

Resources