Hello,
I have a HP IPaq 512 its just over a year old but some time back it froze and I restarted the phone and now it wont go pass the HP Boot screen.
I have tried to hard reset the IPaq using the Center key and the red key but that didn’t work. I got the message for soft reset and got the conformations asking if I was sure… I said yes but again it froze at the HP logo Screen.
I am unable to flash the rom since it’s not recognized by my (WIN XP) pc as a USB device. (Since it doesn’t boot completely)
I have been to HP Service center and the cost they gave me to repair was more than double its buying price.
Could any one please help me this problem here please?
Related
I think my ipaq 3660 is dead, but I hope not, I was hoping to try and put linux on it. Here's the scenario, I bought it from a guy who says it was working till a rom upgrade went wrong (power cut ).It appears to charge up OK, with the light eventually going solid. Active sync finds it and identifies it correctly but can't connect, advising me to turn off usb connections to stop repeated attempts to connect.A hard reset results in a screen of black and green vertical lines with 2 rectangular boxes near the top which look like text boxes, but with no text.I have download a rom update from HP, but of course it won't install without active sync connecting.Does anyone have any ideas how to save it? I have succesfully upgraded my xda2 a number of times (now ce 6.1) so I have a limited ability.
Thanks in advance
I got some more info from handhelds.org, if I press and hold joypad button then press reset, I get a picture of a parrot, this I think is bootloader mode? It seems if I get this far perhaps all is not lost, it appears this is not uncommon with this ipaq. Unfortunately the solution seems to be to connect to a pc with a serial cable to copy over needed files, but my cradle is only usb, and I'm reluctant to spend anymore on what could still be a lost cause.
Any ideas?
Hi all,
Once upon a day, i rebooted my ipaq 6340, after the progress indicator is on the end, it takes more then 1 hour! until the win mobile screen shows up.
My ipaq also behaves like this when doing a hard reset.
I can put the ipaq in bootloader mode, when i put it in the craddle it says USB BL, when i take it outside the craddle there still stands USB BL
The official rom update, doesn't work. After rebooting it hangs (again for + 1 hour) and the updater application does a timeout.
Unofficial rom updates (like the one in the sticky thread) also doesn't work. (The hosts pc screen stays at : veryfying the information on your ipaq pocket pc ... please wait)
Other things with this ipaq which also go wrong : if i try to activate the phone (via ipaq wireless, sim contact, mini tasktray above on the today screen etc), the ipaq locks up.
Any help, official patches, unoffical patches, programs to mod the rom by usb telnet or whatever, ideas, etc extremely appreciated.
I did an update withthe ROM and utility off the HP site which then came up with a message about lost comms on the USB port. I left ist sitting in the cradle connected for about an hour but nothing was happening so I unplugged it from my win7 machine and tried with an XP machine. Still no luck.
I have tried the reset, combinations of power contacts iTask and reset button and power calender iTask and reset but nothing changed, it still had a blue screen with no back light. I pulled the battery lead and the screen changed slightly but nothing else.
Any ideas how it can be resurected?
I have followed the instructions from forum.brighthand.com ipaq-h3600-h3900-series 273231-h3630-bricked and that has shown how to get the iPaq ready and what software to restart the process with (host11) but everything goes fine up to 98% when I get a message 'lost USB communications' and it stops.
Does this mean I have bad sectors in my ROM chip? How can I fix this?
Is there a linux ROM which would fit in less than 98% of 16 Mb?
Please help.
Hi
I have a W500 I did a clean install of windows 8 onto, it booted fine a couple of times and now when I switch it on all I get is the windows key on the tablet blue and a black display. I can tell the tablet is on and is attempting to do somethings as I can see the usb dvd-drive I attached via the keyboard trying to read. I tried holding the windows button on the tablet and powering on but I have had no luck getting the device to even display the bios, I even disconnecting the msata drive to see if it would at least give me a message but I had no luck.
Can anyone help me to unbrick my Iconia W500?
Hello,
i brought a Mpman Converter 10 tablet past week, and i am facing some weird issues and seems no one want's or know to help me. Everything started with the offer, it was advertised that this tablet is running windows 10, but when i brought it i saw on the box it was written windows 8. I was thinking that no big issue and i downloaded windows 10 anyupgrade or what is the name, i left it over night to make the update. When i woke up the tablet was frozen i restarted the tablet but the OS was not starting, i tried startup repair with all the combination but nothing helped me. So i decided to download a windows 10 iso from microsoft and install on tablet, with a lot of issues because the manufacturer didn't gave me any cd with drivers nor on the website no driver is provided i contacted the manufacturer via e-mail but he was not handy at all and send me back to my reseller. My issue is that all the drivers are installed on the OS but the touch screen is not working corectly it got an Silead MSSL touch screen with the hardware ID: ACPI\VEN_MSSL&DEV_1680.
The issue is that the touch screen got an offset when i touch the screen and also seems that the x and y axis is reversed i tried all the drivers what were recommended by others for the similar touch screen.
I can't find any help i hope someone could give me some hints what to do next.
sensor is kionix. if you have driver in device manager problem is from intel (Intel(R) Trusted Execution Engine Interface). install version 1.0.0.1064 (date product 09.01.2014) by intel
Mp man converter 8
Hello. I have the same problème with my tablet mpman converter 8. And i tried to install reinstall windows but the problem persists