Interesting little problem I discovered when trying to reflash with Dutty's latest ROM.
- I connect via USB and I do not get the standard USB 'ding' noise when I plug in.
- I checked system hardware properties, all of my USB drivers are working and no yellow flags.
- Active SYNC is configured just as it was when I first synced my phone a month ago to my PC
- I hard reset my tilt a few times with no solution.
I tried a few different computers and they all displayed the above problem.
The TILT charges fine when connected to my PC so I know its not a hardware issue...I did notice that the active sync icon under my connection manager was constantly grayed out and even after enabling it remained gray, its been a while since i synced with my PC and I do not remember if it only turns green only in the process of syncing or not...
Im pretty stumped on this one any ideas?
Settings >>> Connections >>> USB to PC >>> Deselect check box for Enable advanced network functionality
This sounds strange, but do you have multiple network cards in your computer? If I disable my primary network connection and enable the dirty connection my tilt wont connect to ActiveSync and the icon goes gray. As soon as I switch back it works again. It had me stumped for the longest time.
Could be related, maybe not.
check your Firewall Settings.. (if you have one). If you do, then i recommend that you delete the entry for activeysync, rapimgr.exe and add the rule.. i get this once in a while
man... turned out to be the USB port on the phone, everything looks normal but upon further inspection it appeared that the 3rd pin was slightly bent towards the back of the connector. It was a major pain in the butt gently bending it back without damaging the connector... what a headache!!
How did it get bent in the first place??? Thats the question
Many thanks for the tip. I had the same problem with my TyTN (charged over cable, synced only when using a 3rd party cradle) even though I took pretty good care of it. It was bent in the same direction as the other similar threads suggest, but the only thing that helped me was bending backwards the 3rd pin. It's a shame that I damaged the connector in process, but that's better than not being able to properly sync the bloody expensive device that already cant play video and lags in camera/menus
I always thought iPaq's were badly engineered with 2210's falling apart but is seems that HTC outperformed them here. At least HP didnt try to save a few cents on the sync/charge port. Way to go HTC.
Hi Guys.
It might seem funny. I do not have a PDAphone but I have a problem with my HPiPAQ hx2795. And I would greatly appreciate any comments or tips.
Here is the story:
I was trying to update setup/ROM. the first three updates went well. The forth one, didn't go through; it was showing time-out. it happened twice, the third time, I noticed a message on the left lower corner of the device,saying Connect A/C to flash, I tried to do it quickly before getting time-out. I guess I didn't do it quick enough. Anyway I plugged in the power to the cradle and it started flashing the ROM then I got the time-out error again. The screen reset and stuck @100% not going any further. To make it worse to me, it was not detectable by MS ActiveSync at all. I tried the active chat with the tech support of HP they said all is left for me to do is "going to parrot mode (= USB /serial Mode) and if the OS is not corrupted then I can repeat the ROM update and fix it" which I did with no luck as even in parrot mode, the device would noticed that the USB is connected but the PC would NOT recognize the device.
While I was searching the internet, I came across your site, beautiful and very interesting. I saw some people is using a program called NVID.exe.
IS THERE ANY SOFTWARE LIKE NVID.EXE THAT I CAN USE IT TO SOLVE MY PROBLEM on this HPiPAQ.
I was wondering about using something like that to get the device detectable by PC again. Is is possible even theoretically?
Please HELP.
I greatly appreciate all your comments and tips in advance.
Did you tried to do a clean reset? Or to put the device in bootloader or white bootloader mode and try to connect and see if recognize it?
Hard reset: butons 1+4+reset
Clean reset: buttons 1+3+power+reset
White bootloader mode: buttons 2+4+reset
what you call it "white bootloader mode" they call it "parrot mode". and yes I did try that. In that mode it shows Pre-BL: 1.00.04 that shows USB is connected or USB Cable is removed; however; my Win XP cannot recognize the new USB device.
Is there any way to make PC recognize this "HPiPAQ hx2795 in Parrot Mode". I mean any driver for WinXP to recognize this USB device as reachable device (updatable ROM)? Maybe that could be the "MAGIC KEY" to solve all people's problem suffering from such an issue?
I hear about mytt11.exe alot in posts here and there. What does it do? Where can I find it in order to give it a try?
Coolluck
------------------
HPiPAQ hx2795-WM5, failed ROM update
Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve
I've got the same problem. I can't connect via AS:/
I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.
Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve
It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.
Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve
Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?
Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.
Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.
This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?
Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck
Can You Tried Different Usb Cable :d
i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us
I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.
Hi friends,
I am having a very weird situation here and I need your help.
My phone was working perfectly after the last time I have upgraded the rom which happened a couple days ago. Then yesterday I have discovered that my phone is turning on and off on its own. It turns on, then after a few seconds it turns off and then turns on again.
When I hard reset, it gets stuck at the smart mobility screen.
I can enter the bootloader screen by pressing the camera key and inserting the usb cable. The tri-color screen shows usb at the bottom left corner. When I run mtty, it says the usb port cannot open.
I know that it has sufficient power in the batteries (tried with two different batteries I have). However, when I plug it to a wall charger the charging light doesn't turn on.
So basically I have a tornado which cannot boot, mtty seems not able to recognize it. Is there any way to push an SPL, radio rom or OS rom to the phone? Is it possible to flash a tornado with an SDcard?
I really need some help here as I am out of ideas. thanks in advance.
Did you try hard resetting it? (While off holding both softkeys and then pushing the power button)? If so, flashing from card is possible...you just have to install the original ROM though. Google this: Tor_TMOUS_10140_191916_10900_SHIP.exe
Extract it then copy the nbf file to your memory card.
You may have to rename it and change the headers though...that I don't know
Here might help you by the way
http://forum.xda-developers.com/showthread.php?t=409286&highlight=original+rom
Good luck!
Your problem is more likely seems the power key is stuck.
thacen said:
Your problem is more likely seems the power key is stuck.
Click to expand...
Click to collapse
I am almost sure that this is not the case because I can use the power button for shutting the device off and restarting it, etc.
My only hope is to be able to flash from the SDCard now, as unforsakenrule mentioned. The problem is I need a step by step guide to do that.
burkay said:
When I run mtty, it says the usb port cannot open.
Click to expand...
Click to collapse
Did you disable the USB connection from ActiveSync properties?
I had had a similar problem which was solved after reinstalling the ROM.
NiTroGenious said:
Did you disable the USB connection from ActiveSync properties?
I had had a similar problem which was solved after reinstalling the ROM.
Click to expand...
Click to collapse
sure I did. The problem is no matter what the device is not recognized by the pc. mtty, activesync, tera term, etc. all fail whether usb connection is enabled or not. Weirdly, in the bootloader menu it says USB in the bottom left.
It really sucks, because I have the bootloader there but I cannot load anything to the device to recover it.
While it is in bootloader screen activesync couldn't connect or it could not detect your device. If you want to connect by teratermpro you need to disable USB connection from active sync otherwise teraterm could not connect your device.
I think your PC will not show you any connection symbol while connecting in bootloader but you may hear some sound while connecting or disconnecting.
One thing you can try is just try reflashing a stable rom by just running RomUpdateUtility. If it cannot find your device then check on your PC's Hardware device manager, if there is any unworking driver. if such driver is there just uninstall it and try connecting again.
May be it can solve your problem.
thanks for the advise, but I pretty much tried everything... everything except an SDCard flash. And that, I don't know how to do. I have been an HTC user for the last few years. This iMate SP5, which I owned a year ago, belongs to my sister now. I now have a Hermes, waiting for the prices to come down before ordering my touch pro. I flashed tens of roms in both devices, connected using mtty, teraterm etc. many times. This is the first time I am totally left clueless and I believe this is what we call a brick, indeed