So I've had my fuze a little over a year now, no major issues. Used mostly energyroms, but about December time I switched back to a simple non-bloated stock rom for the stability.
Anyway today at work I was texting, and I press the power button to put the phone in standby. And the screen remains on and usable. I tried again and it would not go into standby (power button physically feels normal, it does not feel loose or abnormal.) So i let it sit for a few minutes, then i look at it and a message poped up asking if i wanted to turn the phone off (like as if i was holding the power button)so i press no, then it comes up again a few seconds later and aagain and again. So I soft reset the phone.
The phone resets but takes a LOT longer at the att/htc splashscreen, then it hangs at the htc screen and does not make it to the wimo screen, but instead an error screen saying:
"The device is unable to boot because you have either turned off the device incorrectly or tried to install an applicationa from an untrusted source, press SEND to reset your device or press any other button to cancel..."
I think it went through the hard reset this time because when it restarted it asked to calibrate the screen and install stuff. it resets again sometime after that, still takes forever at the splash screen and comes back up to the error, only this time no matter what button i press it wont go away and boot into wimo. It seems like none of my buttons work (they wont light up now) when i slide out the keyboard, it is not lit up like normally.
And heres the kicker, my only way to turn on/off the phone is to take out/put in the battery. As soon as I pop the battery back in the fuze turns on. Is my phone toast? Ive tried to hard reset and the phone does not reach the bootloader, it goes straight to the splash screen. Same with trying to reflash it from my comp, raphealwrapper cannot find my phone.
I've only recently encountered the exact same problem on my Touch Pro, but stock ROM and everything. As far as I can tell, our power buttons are busted and probably need to be serviced. One of the contacts must be stuck in the 'on' position somewhere inside :\ As a temporary fix, I've been using AEButton Plus and remapped double tap end call key to turn the screen off, and removing the stylus to turn it on.
Related
Hi,
I have upgraded my MDA to NO EVIL ROM Windows mobile 6 version from this forum. Device was working great for couple of weeks. Now suddenly it stopped booting. When I do soft reset the
S.N.E ... Presents screen comes up.
Then HTC Wizard screen comes up
The Touch No Evil screen come up and then it stays at the same screen. It does not respond even to power button now.
The radio light (green light) blinks. The system does not respond to even hard reset.
I am tosed. Please help. Any response to recover from this situation is usefull.
Thanks in advance...
From the sounds of it, something you have installed or configured isn't allowing the phone to finish booting. You basically have 2 choices at this point... Hard Reset or Reflash the phone.
When you say hard reset doesn't work, are you sure you are doing a hard reset? Pull the battery out and let the phone rest for a minute or so. Press the power button a couple of times (yes with the battery out) to discharge any power in the device. Then put the battery back in, and press the top two buttons on either side of the phone (Comm and Record), and while holding those in press and release the power button. After a couple of seconds you should have a black screen with white text asking you about resetting the phone. Press the Send key (the green phone key that you use to answer the phone) and you will have completed the Hard Reset. If you get errors then you need to tell us what they are. If you never get the black screen with white writing then you aren't holding the buttons down correctly.
To reflash the phone, put it in bootloader (press and hold the recorder button while pushing in and releasing the reset button (or while turing the phone on)). Once you get the tri color screen, hook up the USB cord and it should say USB in the lower left. Now you can flash it (even though the phone won't connect to ActiveSync).
Good luck and hope that helps.
Able to reboot
Thanks for the advise. After several tries, was able to hard reset and started booting and working OK.
I have not done any soft reset after this event. What should I look for to correct, if any errors.?. do you recommend that I reflash the ROM?. The only software, I had installed was Microsoft Voice recorder. I have not installed the same after the reboot.
Thanks
ANother issue
Now after resetting, I see my phone getting into vibration mode all the time. Even if I set to ring mode, it will automatically go back to vibration mode after some time. Any idea on how to fix the same?.
Thanks
So this is a weird problem I just started having today.
After putting my phone away during practice, I came back to find that it had only 1% battery.
It died en route to my room, and when I first plugged it in to my PC, it turned on and worked normally. After a while it turned off.
Now, when I try to turn it back on, the htc Raphael screen comes up, and it makes a short vibration, then goes to black for about 1 second, and then repeats. It has been doing this nonstop.
However, it only does so when it is plugged in to a power source. When it is not plugged in, it is completely unresponsive.
I have the elite RC2 ROM that I flashed back in November.
Any suggestions?
hard reset to start things off.
Hold down the volume down button, center button and then press the reset button with the stylus until you see a screen that says something like "this operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel." then press volume up. Remember you will lose all data, phone numbers and anything else stored on the phone.
i know this problem
I have had several, i solve it taking press the power button long time during the boot.
Of course, the phone must be plugged in to a power source.
Problem solved.
I left it unplugged with the battery out overnight, and then plugged it in to charge, and it did not attempt to startup.
After letting it charge again it worked as normal.
I suppose the battery was so run down for some reason, that even plugged in, it did not get enough power to complete the boot.
It works now. About to flash Elite RC3 and a new radio.
I just received a new Fuze from AT&T as a warranty replacement (my old one was draining the battery quickly, overheating, etc.). I reverted the old one back to stock and that is ready to be sent back.
Now the issue: I opened up the new one. Powered on, seemed okay at the time (now I remember that I bumped it and it randomly reset at the carrier splash screen, didn't think much of it then, but clearly a problem). It seemed to work okay, so I flashed HardSPL and put on a custom ROM. Continued to work okay. Then I turned it off.
This morning, I go to turn it on, find it will not power on at all. Then I try again, after pulling the battery, and it starts booting, but then I jiggle it a little and it shuts off. Try it again, it freezes at the carrier screen. Basically it won't turn on.
Now I put the battery in the Fuze I'm sending back (which at least boots) and find that overnight, with the phone off, the battery dropped from 95% to less than 5%!
Basically I think this phone is a dud, but I need to get it back to stock SPL and ROM to send it back! I'm currently re-charging the battery in the old Fuze in the hopes I can get the new one to boot.
Any thoughts or solutions?
Still no luck in booting up even with a full battery...anyone have any ideas??
try this...it worked for me when i had a similar problem...!
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and CENTER buttons, then press the RESET button with the stylus tip.
3. Continue pressing the RESET, VOLUME DOWN and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
kaydash said:
try this...it worked for me when i had a similar problem...!
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and CENTER buttons, then press the RESET button with the stylus tip.
3. Continue pressing the RESET, VOLUME DOWN and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
Click to expand...
Click to collapse
Yeah thanks I would definitely try to do a hard reset...problem is the phone won't turn on
Any other thoughts? I am thinking I will just have to send the phone back to AT&T as is in the hopes that it really is bricked completely and that they won't turn it on to find a custom ROM and HardSPL.
That sounds like a bad idea; if they find out you hacked the new one, they're gonna be pissed that you sent in the previous phone for exchange.
So, you can't get it into bootloader, to at least flash back to the stock rom? You said it wouldn't boot up, but how about plugging it in and seeing if you can get in bootloader? That's what I'd do. You actually don't need the battery once you're in bootloader, if you have it plugged into a wall charger or connected to a PC through a usb cable.
Basically, the phone stays dark what ever I do. I can't get into the bootloader or anything, the screen and all lights won't come on, period. The battery works fine in other phones as well. Very puzzling.
Any other ideas? I suppose if they do manage to get the phone to power on, I can just play dumb about HardSPL...I've even read about people getting phonse with HardSPL back from the warranty department. The phone is probably bricked anyway from what I can see, so I guess if they manage to spark it to life, I will just have to play dumb...
Hi! So... I installed Magldr V1.13 many months ago and it has been very awesome. Yesterday, while sitting in class, my phone was in my pocket. (very rare occasion as I usually have it in a holster)
Anyhoo, it vibrated twice like it would for an email or text. I pushed the red (hangup) button to see the screen, and the screen stayed black but the buttons lit up. I repeated, same result. I took the battery out, turned back on and the phone stops loading after the "GO GO GO!". It just sits there.
I have taken the battery out and restarted it literally 12 times. I tried with and without SD card and Sim Card. I even tried holding in the yellow reset button. I don't know what else to do.
Any help is very much appreciated!
hope you find out the problem, I uesd to be in your situation, so sad
kimmy8705 said:
Hi! So... I installed Magldr V1.13 many months ago and it has been very awesome. Yesterday, while sitting in class, my phone was in my pocket. (very rare occasion as I usually have it in a holster)
Anyhoo, it vibrated twice like it would for an email or text. I pushed the red (hangup) button to see the screen, and the screen stayed black but the buttons lit up. I repeated, same result. I took the battery out, turned back on and the phone stops loading after the "GO GO GO!". It just sits there.
I have taken the battery out and restarted it literally 12 times. I tried with and without SD card and Sim Card. I even tried holding in the yellow reset button. I don't know what else to do.
Any help is very much appreciated!
Click to expand...
Click to collapse
Always it happens something like that out of nowhere. So I think the solution is only one. Factory Restart the phone and re-install everything from the begging. If you don't want to loose your stuff try to copy paste the stuff you got in your SD card.
L0rkh said:
Always it happens something like that out of nowhere. So I think the solution is only one. Factory Restart the phone and re-install everything from the begging. If you don't want to loose your stuff try to copy paste the stuff you got in your SD card.
Click to expand...
Click to collapse
I know right? This is the first time I have been without a phone this long since high school, lol. How can I factory reset it without being able to turn it on? I held down the volume down+home+power button and chose the wipe from that menu. It didn't do anything. I even held in the yellow button on the back, still nothing.
Ok. So I finally found a way to factory reset my phone even though I can't get it to really come on:
1. With your phone powered off, press and hold the VOLUME UP and VOLUME DOWN buttons.
2. While holding the volume buttons, press the END/POWER button briefly and then release it.
3. When you see a warning message on screen, release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the reset, or press any other button to cancel the reset.
Now, it's stuck on the "Stick Together" Tmobile logo
I rooted my HTC ONE S ( EUROPE ) a couple of months ago, everything was fine until yesterday when I went to unlocked my phone from my lock menu it and it displayed a message on my phone screen saying "hold power button or phone will shut down in 3 seconds" by the time i had realised that that message was there it had one second, so it turned off by itself and it wont come back on, it wont let me into recovery or the bootloader because the screen wont come on!! I've tried volume down and power and it doesnt work, the only thing it displays is a solid orange LED light when i put my phone on charge and my computer doesnt recognise it when i plug it into it? I cant contact my service provider ( o2 ) because i void the warrenty when i rooted. HELP?
Full charge your phone, unplug it and try again.
My phone used to do a really annoying thing when it ran out of batteries. The next time I went to turn it on I had to hold the power button for about 20 seconds. After the first 5 seconds, the soft-keys would start to flash. They continue to flash as you hold the power button. Then, after a while they stop flashing and the phone boots up. Like I said, it takes a while. Just keep holding the power button if you see the soft-keys flashing.
That doesn't seem to be a problem now that I'm on Beanstalk 4.4.