Hello Everyone
I have an qtek s100,t-mobile version,windows mobile 2003
I have to change rom because i Will give it as a present so....I downloaded a rom to take on the phone(http://forum.xda-developers.com/showthread.php?t=490948) but when i take the phone to bootloader mode,it says usb down the screen but it doesnt connect with pc(activesync-windows xp)
what can I do??
Related
Hi everybody.
Today i tried to upgrade my O2 xda mini with GERMAN ROM installed. I would put italian ROM 1.12. I follow all the instruction reported in forum but after few minutes Maupgrade_NOID have stop and the xda is turn in Bootmode.
I have Vista and Mobile Center Device with USB connection untick.
Now seems like Xda have no ROM installed and the flash via SD don't work. I have no Backup of Original ROM
Someone can help me please?
Sorry for my poor english
Christian
1. enter bootloader mode
2. connect the usb to pc
3. any rom install via Maupgrade_NOID (no sd boot - direct usb conn.)
All Ok
Fortunately it was only a problem with the PC O.S.
In Vista there are many problem of compatibility
I Installed XP and all gone very good....
ROM Upgraded in italian and XDA mini work perfectly!!!!!
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Flashx4u said:
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Click to expand...
Click to collapse
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
The problem SOLVED!
ZRimaZ said:
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
Click to expand...
Click to collapse
So ,finally I found the solution with this issue and problem with my Prophet's restarting after it's registering to the cellular network (I wrote about it in another treeds as well).
After I tried to reflash my Prophet with different WM6 ROMs, different Radio ROMs, reassembled and cleaned it, reflashed to original WM5 ROM and nothing helped, I just came to an idee to replace the battery, unless Prophet indicated that still it's a lot of power (min 50%)...I ordered the battery and when I received it and replaced, everything is running as it should be!!!!
Hello there,
I tried to flas my MDA and now it stays in bootloader (1.01). Whatever I do: it stays there! (hard/factory reset and what not). Whenever I want to install a new rom by a RUU application, this goes wrong as well!Any help would be much appreciated!
Ive the same problem @ the moment! I tried to do a Rom update and then an error appeared and the installation failed and the recovery afterwards aswell! Now my Universal stucks in the bootloader mode showing USB v. 1.01! How can I get out of this mode! I tried the hard reset, like joenie described but i didnt work!
Aalsen said:
Ive the same problem @ the moment! I tried to do a Rom update and then an error appeared and the installation failed and the recovery afterwards aswell! Now my Universal stucks in the bootloader mode showing USB v. 1.01! How can I get out of this mode! I tried the hard reset, like joenie described but i didnt work!
Click to expand...
Click to collapse
I have the same problem sometimes when I change ROM version, the installer reboots the PDA in USB mode and nothing, the installer display an error and crash. The PDA in not recognized correctly in USB mode.
It is due to your PC (Activesync crashes in silent mode and disable WM device drivers) and not the UNI!!!
Try restart activesync (open it), unplug and replug the UNI and restart installer, the installer will not recognize the actual ROM version but it should be working...
If it fails try to restart the PC or uninstall and reinstall activesync and retry installation...
Be carrefull because in USB boot mode the UNI cannot charge the battery, if the battery is down, you cannot restart installation (And cannot disable boot mode).
I was affraid the first time of USB boot lock (It was the panic, UNI bricked...) but now, I know the problem and I resolve it fastly (restart activesync).
Good luck!!!
Hey thanks for all the advices! i found a really good tutorial how to unbootloader it. But the actuall problem is that windows vista is not having any active sync like Windows XP. I now you can download a windows mobile device manager and I tried the deactivation of the USB port over this one, but it didnt work! Is there any other methode oder way how to get access to the phone to change the status?
Thank You very much!
Aalsen
Aalsen said:
Hey thanks for all the advices! i found a really good tutorial how to unbootloader it. But the actuall problem is that windows vista is not having any active sync like Windows XP. I now you can download a windows mobile device manager and I tried the deactivation of the USB port over this one, but it didnt work! Is there any other methode oder way how to get access to the phone to change the status?
Thank You very much!
Aalsen
Click to expand...
Click to collapse
Can you add here the link of the tutorial???
May be try remove usb devices in the device manager of Vista and reboot the PC to redetect the UNI USB drivers.
well lad's and gent's..
I found out what my real problem was
It was a broken USB-cable :|.. wtf!!!
Well anyway. I think you guys are great! all the posts/helps!!
It some else to do???
I try to flash my JASJAR and I brick it........The instaler send my an error and I stuck in bootloader but the instaler window says to cool reset the Universal and the Bootloader was gone and the universal now is death, can't turn on and no Boot...Its bricked and I still crying!!!!.....
Well I have installed a new Rom yesterday on my Q9000...
I whas using my laptop which has Vista on it. Dont know what happend but I got an error msg on my laptop...Tried to reboot my Qtek but it whas hanging on the bootup screen(the 1st screen which shows all Rom/ext rom and Radio version). No matter what I did it refused to bootup...
When plugging in my Qtek on to my laptop, the bootloader screen changed from serial to Usb...
Finally I tried it on the desktop wich still runs on XP and it did the Romupgrade without any pain...
I did several Romupgrades on my Herald all on my Vista laptop without any problems...I don't really understand what or why, maybe because the Qtek is older than the P4350 that it is less compatible with Vista?
Bottom line, I now have a Qtek 9000 which is fast ...
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
pommie said:
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
Click to expand...
Click to collapse
Hi,
The answers you seek are in the WIKI.
Hold the backlight + power button whilst resetting the device. This will put you back into bootloader mode, you can then reflash the Rom.
I would also advise that you SuperCid your device before flashing any Roms, if you haven't done so already.
Again this is documented in the Wiki.
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Cheers,
Beasty
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
pommie said:
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
Click to expand...
Click to collapse
The problem is Vista!
Search the forum and you will find a post with a fix (old drivers) for Vista, or just use a Windows XP or previoous MS OS to flash your device.
I would suggest XP if you plan to keep flashing in the near future
do i need to super cid my htc universal in order to upgrade to ranju v77. my universal is branded dopod 900 and can use with any simcard. thanks
lucky for me, i also got a pc with xp sp2 but my pda works with ranju v77 thnx man.
only from nokia phones i can't send file with bluetooth, phones like samsung works fine
I would like to change my rom to another, but i have a problem.
I cant connect anymore the blackstone to the pc with the windows mobile device center ( i have windows 7). In device manager is not show the mobile device connected. i dont know what can i do to fix it.
So, i tried to upgrade the rom with the microsd, i copied blacimg.nbh and restarted the device by hold volume and power button, but it not flash.
I think becouse i have SPL
how can i change the spl without connect the blackstone to the pc?
thanx
claudioz said:
I would like to change my rom to another, but i have a problem.
I cant connect anymore the blackstone to the pc with the windows mobile device center ( i have windows 7). In device manager is not show the mobile device connected. i dont know what can i do to fix it.
So, i tried to upgrade the rom with the microsd, i copied blacimg.nbh and restarted the device by hold volume and power button, but it not flash.
I think becouse i have SPL
how can i change the spl without connect the blackstone to the pc?
thanx
Click to expand...
Click to collapse
You need to downgrade your usb drivers. Follow this guide on step-by-step procedure on how to flash a rom including how to downgrade drivers
http://forum.xda-developers.com/showthread.php?t=505377
Also, any further queries, please post in that thread