Hi everybody.
Today i tried to upgrade my O2 xda mini with GERMAN ROM installed. I would put italian ROM 1.12. I follow all the instruction reported in forum but after few minutes Maupgrade_NOID have stop and the xda is turn in Bootmode.
I have Vista and Mobile Center Device with USB connection untick.
Now seems like Xda have no ROM installed and the flash via SD don't work. I have no Backup of Original ROM
Someone can help me please?
Sorry for my poor english
Christian
1. enter bootloader mode
2. connect the usb to pc
3. any rom install via Maupgrade_NOID (no sd boot - direct usb conn.)
All Ok
Fortunately it was only a problem with the PC O.S.
In Vista there are many problem of compatibility
I Installed XP and all gone very good....
ROM Upgraded in italian and XDA mini work perfectly!!!!!
Related
hello ,
i bought an i-mate jam , but the OS version language is in french. At first activesync worked correctly , but now i' m trying to connect the magician even on others pc and other version of activesyc ... but doesn' t work !!
So I red carefully all the threads and post of this forum and download rom and instructions for doing an upgrade to Italian Language Version :
I enter on the bootloader mode, I disactivate activesync , and now when I plug in the USB cable, I see a write USB v.1.02 sO i think the pc recognize the pda , but when I launch MaupgradeUt , does not recognize the i-mate ROM version, I tried many times , even with other pcs , but nothing !!!
BUT I'M NOT USING THE ORIGINAL USB CABLE OF I-MATE , BEACUSE WHEN I BOUGHT IT THEY DID NOT GIVE ME. I' M USING A MINI-USB CABLE OF BLACKBERRY , BUT IN THIS FORUM I RED THAT IS THE SAME ...
I ALSO DOWNLOAD THE LAST GUIDE FOR UPGRADING MAGICIAN ...
Does someone know where is the problem ? When I unplug the usb cable Do I have to hard reset any time after i enter the bootloader ?
Please help me, even becuse with this Rom I cannot use activesync for install programs ....
p.s. : the phone works correctly, the only problem is activesync
About the ROM upgrade - your cable is fine, if the PDA detects the USB connection (ie. shows 'USB' on screen) then the connection is fine. Try running romupdate.exe and getting it to backup your ROM by using the 'd2s' command (its somewhere in my guide... sorry I'm in a hurry so I can't give you the exact location yet). If this suceeds, then you should be clear to attempt an upgrade regardless of whether the update software detects your current ROM version or not - but keep that ROM image on the SD card just in case. The worst thing that will happen is that your ROM will be corrupted (this is rare), but even then it is a rather painless process to restore your original ROM since you have it backed up on your SD card.
About the ActiveSync problem - try soft resetting your Magician. If it still doesn't work, try a hard reset (but back up your data first, of course). ActiveSync can be rather glitchy sometimes.
hello ,
I tried the instructions you gave me on the post ,, i tried doing the backup rom with all the instructions of your PDF guide but :
- the phone gave me USB ver. 1.02 ,
disactivate the activesync ,
run romupdate.exe
- but on the port setting I had only two options COM1 and COM2 , but no way for \\.\WCEUSBSH001
Have I any possibility to change the ROM , maybe with a flash SD CARD method ?
IS IT POSSIBLE TO USE THIS GUIDE http://forum.xda-developers.com/showthread.php?t=235734&highlight=ROM+UPDATE OF THE SD CARD FLASH
WITHOUT DOING A ROM BACKUP ( ROMUPDATE DOES NOT WORK WITH MY PDA -)
- Today I even tried on my brother pc portatile , but here the " MaUpgradeUt_noID.exe " WAS about 3 hours saying me to not disconnect the pda .... but after 3 hours I unplugGed it , i did a soft reset and automatically installed all the applications ( hard reset)
instead on my pc it does not recognize the rom
- When I received the phone activesync was working fine , then I download an italian version rom from clubimate, I ran it , and give me " Country ID Error" , FROM THAT MOMENT ON MY PDA NEVER RECOGNIZE AGAIN ACTIVESYNC on any type of PC
is it possible that the wizard originale rom corupt my pda?
the only problem is the activesync
- BUT IF ON THE BOOTLOADER IT GIVES ME USB V.1.02 IS THERE A POSSIBILITY TO SOLVE THE PROBLEM?
- Is there a way to flash the ROM from the SD CARD ?
- Is there a probality that with a new ROM , activesync will work again ?
Thank you very very much toomuchdogfur for helping me , please I NEED A HELP , are about 4 days that this phone is making me crazy ...............
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Flashx4u said:
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Click to expand...
Click to collapse
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
The problem SOLVED!
ZRimaZ said:
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
Click to expand...
Click to collapse
So ,finally I found the solution with this issue and problem with my Prophet's restarting after it's registering to the cellular network (I wrote about it in another treeds as well).
After I tried to reflash my Prophet with different WM6 ROMs, different Radio ROMs, reassembled and cleaned it, reflashed to original WM5 ROM and nothing helped, I just came to an idee to replace the battery, unless Prophet indicated that still it's a lot of power (min 50%)...I ordered the battery and when I received it and replaced, everything is running as it should be!!!!
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
pommie said:
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
Click to expand...
Click to collapse
Hi,
The answers you seek are in the WIKI.
Hold the backlight + power button whilst resetting the device. This will put you back into bootloader mode, you can then reflash the Rom.
I would also advise that you SuperCid your device before flashing any Roms, if you haven't done so already.
Again this is documented in the Wiki.
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Cheers,
Beasty
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
pommie said:
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
Click to expand...
Click to collapse
The problem is Vista!
Search the forum and you will find a post with a fix (old drivers) for Vista, or just use a Windows XP or previoous MS OS to flash your device.
I would suggest XP if you plan to keep flashing in the near future
do i need to super cid my htc universal in order to upgrade to ranju v77. my universal is branded dopod 900 and can use with any simcard. thanks
lucky for me, i also got a pc with xp sp2 but my pda works with ranju v77 thnx man.
only from nokia phones i can't send file with bluetooth, phones like samsung works fine
Hello Everyone
I have an qtek s100,t-mobile version,windows mobile 2003
I have to change rom because i Will give it as a present so....I downloaded a rom to take on the phone(http://forum.xda-developers.com/showthread.php?t=490948) but when i take the phone to bootloader mode,it says usb down the screen but it doesnt connect with pc(activesync-windows xp)
what can I do??