Related
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
thimiost said:
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
Click to expand...
Click to collapse
OK lets start at the basics...... In bootloader mode (tricolour screen) what text does it say at top of the screen?
Have you DEFINITELY Sim Unlocked and CID unlocked?
it says these things
kais130 mfg
spl-10.0.Olipof
cpld-8
Ok that confirms you have the capability to flash. I have seen in the past some people have managed to flash one time only using jumpspl but then their device reverts back to original bootloader...I was one of those people
Next question then...Can you boot the phone normally and gain an activsync connection to it?
yes
i can use my phone normally
only i cannot put a new image in
Are you using Xp or vista? If using vista it may be worth trying a reboot... sometimes it goes doolally with its usb ports. If you cannot see the phone through WMDC or activsync after a reboot it is worth going to SYSTEM (on your PC) viewing non present devices through device manager,( Drop to Command prompt and type... Devmgmt.msc set DEVMGR_SHOW_NONPRESENT_DEVICES=1 ) removing the relevant phone connection and then re attaching it so that windows re detects it.
If you can get a connection via actvisync (win XP) or WMDC (vista) to your phone then all should be ok. Uncheck the activesync/ WMDC "allow USB connections" and try again.
If this still doesn't work then search around here for MTTY. That will allow you to specify the usb connection to the device...amongst other things.
thank you for your time
i have win xp and activesync works nice
the problem is when bootloader starts
When you attempt flashing, do you do it from the device already booted into windows mobile or direct from bootloader?
Which ever way you have tried it, try ther other way.
Not teaching you to suck eggs but just in case you dont know.... To get direct to bootloader hold camera button and soft reset with stylus whilst holding camera button down and the tri colour screen should appear.
With device at the bootloader screen, Can you confirm that you hear the windows "noise" when you unplug and re plug the USB cable just as you would when plugging and unplugging the device normally. This will determine if the device has connection at the bootlaoder stage.
why not just flash using the microsd card. its much easier that way
yes it has connection
the thing is that i have already flashed as i told before with dutty's v4
now i can't
Usually Error 260's are related to the USB port functionality ( Port can't be opened etc).
The SD card method or MTTY should sort you out.
thx again
hope it works
at least the sd trick worked!!!!
now running on winmob 6.1
Glad to hear you sorted it.
almost
i cannot use my sd card cause i have to have it formated in order to put a new rom in
thimiost said:
i cannot use my sd card cause i have to have it formated in order to put a new rom in
Click to expand...
Click to collapse
disable USB connections in ActiveSync and flash.
This Link gives a list of eror codes for Hermes, and probably the same for Kaiser.
It's likely that you have a USB port error - maybe try changing the USB port you use or a different sync cable - or just stick to SD card flashing in the future - I keep an old 1gig card for this.
this IS the problem...i cannot flash...
it stays in the bootloader with the message i wrote
thimiost said:
it stays in the bootloader with the message i wrote
Click to expand...
Click to collapse
It happen to me before hardspl again fix it, not sure why
you mean use the sd method to do hardspl again?
OHHH lord dutty we need your new rom
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
pommie said:
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
Click to expand...
Click to collapse
Hi,
The answers you seek are in the WIKI.
Hold the backlight + power button whilst resetting the device. This will put you back into bootloader mode, you can then reflash the Rom.
I would also advise that you SuperCid your device before flashing any Roms, if you haven't done so already.
Again this is documented in the Wiki.
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Cheers,
Beasty
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
pommie said:
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
Click to expand...
Click to collapse
The problem is Vista!
Search the forum and you will find a post with a fix (old drivers) for Vista, or just use a Windows XP or previoous MS OS to flash your device.
I would suggest XP if you plan to keep flashing in the near future
do i need to super cid my htc universal in order to upgrade to ranju v77. my universal is branded dopod 900 and can use with any simcard. thanks
lucky for me, i also got a pc with xp sp2 but my pda works with ranju v77 thnx man.
only from nokia phones i can't send file with bluetooth, phones like samsung works fine
i flashed from SD my eten X650 with the original rom from X500 by a mistake.
is there someone to help me solve this problem.
it can boot now from sd.
BUT
if i press(camera+power+reset0buttons my pc recognize it likeMICROSOFT USB SYNC devise but it can conected with microsoft active sync
please help me and ican pay someone if he make it work again with 50€
bear79 said:
i flashed from SD my eten X650 with the original rom from X500 by a mistake.
is there someone to help me solve this problem.
it can boot now from sd.
BUT
if i press(camera+power+reset0buttons my pc recognize it likeMICROSOFT USB SYNC devise but it can conected with microsoft active sync
please help me and ican pay someone if he make it work again with 50€
Click to expand...
Click to collapse
Just flash it with the rom for the X650 and you'll be back to your old self. The fact that it can still boot is a good thing since apparently you did not brick the device.
when i try too boot my X650 my screen becomes white and nothing hepens.
then i connect it with pc and recognize it.
i thing that i can flash it.
any other solution?
thanks
Flash from your pc then if your pc recognizes it. By pressing camera+power+reset0buttons i'm guessing you are talking about the bootloader.
yes.for bootloader menu i am saing.
how i can boot it from pc?
if you are stuck in bootloader, then your pc will not recgonise the devise for activesync (or for the RUU software), i think you have to use mtty
i think thay mtty is only for HTC or i am wrong?
This is exactly why we are always telling people to read before doing these things, so that they do not mess up their devices.
Anyway, get your device in bootloader mode and connect it to the PC. You must kill Active Sync (I am assuming that you are using Windows XP and not Vista). In order to kill ActiveSync, you must open the Task Manager and kill the processes called rapimgr.exe and wcescomm.exe.
Once you've done that, you must run the upgrade/rom upgrade utility program in your computer and follow the instructions on the screen. [highlight]Please make sure that the rom that you are using is specific for your device.[/highlight] Otherwise, you will brick your device for certain...
Note that upgrade instructions are, under most cases, device specific. Make sure that you follow the instructions in your upgrade precisely. Most rom cooks post either Readme.txt files along with their roms or they post very precise instructions in the forums. What I just gave you here is a very general set of instructions that normally work for most devices. I do not have an Eten (never have), so I am uncertain if these instructions will be useful to you. Follow them under your own discretion. [highlight]I am not responsible for any damage to your device.[/highlight]
Good luck...
it ask me again to connect wiyh active sync
Ignore. was moved
HELP mE please
soo no solution has found
bear79 said:
soo no solution has found
Click to expand...
Click to collapse
Just read my post. If the device is in bootloader, it should not try to connect to activesync, the pc should only see a USB device. Look for a rom upgrade for your phone and look at the upgrade instructions and follow them exactly. Your phone is not bricked, it only needs to be re-flashed.
i have tried that but nothing heppens.
when i try too put it in bootloader menu my sreen becomes white.
is this bricked phone?
Yes if you cannot get into your bootlaoder, it is bricked.
Hello guys!
I've got a bit of a problem here, because now my mobile refuses to connect with activesync and therefore making it impossible to flash it.
I read the readme in the cid bypass folder, and didn't quite understand it, but as keen as I was on getting a new rom I did it all wrong.
I actually copied the cid bypass folder to my sd-card and ran haret.exe from the phone. A friendly penguin appeared along with some green text, and it rebooted and went black. I waited for a while, but had no patience so I rebooted it again. But after this it has been impossible to connect it with activesync! I've tried hard reset and different computers but nothing works!
I'm hoping someone on this forum can help me!
best regards
Try this.
turn your phone off and press the camera button in then plug it into the USB port
you should get a multi color screen. If you do then you can flash.
But go here http://forum.xda-developers.com/showthread.php?t=330909
Go to where it says EDIT and follow what it says.
Oh and when a dos box opens up and ask you things just press the return key each time.
good luck
hey man, I tried reflashing the original rom to my vox, with the manualstyle sd card flash. So now it's flashed with the original rom, but still activesync doesn't work! anybody have an idea on how to make this right?
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
zipuz said:
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
Click to expand...
Click to collapse
I am confused..is it working or not? one post you say it is but you cant sink..then you say its not.????
and dont use the flash off the mem stick..use windows..
ok, sorry for making confusing posts! I'm just excited about getting it to work.
So here's the situation:
From stock phone used with exchange (turned off the exchange part before doing anything)
1. I ran haret.exe from my phone, and it rebooted into a "black state" after which I rebooted it again
2. I tried to connect it to my computer using activesync, to be able to flash, but it wouldn't connect. Activesync doesn't respond to my phone.
3. I flashed the shipped rom to my phone from my sd-card in good hope that it would reset the whole process, but it still won't connect to activesync.
So here's my problem; I want to flash a cooked rom to my phone, but I'm unable to connect it to my computer via activesync, what to do?
deuse said:
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
Click to expand...
Click to collapse
tried with both ticked and unticked, still nothing
Turn off your phone then keep the camera button pressed in at the same time plug it into the usb port
your should show diff colors on the screen..if so follow what it says in this link.
http://forum.xda-developers.com/showthread.php?t=330909
and do it from the pc not your mobile...
it's restored, but no activesync still
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
ivanek666 said:
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
Click to expand...
Click to collapse
Have you been into settings and un-ticked the box in USB to PC?
Also if you are trying to sync to office you must create a new partnership
google is your best friend.
I have no problems with sync in XP/Vista?windows 7 and office 2007
I am using FMs 1.1 WM 1.1
deuse said:
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
Click to expand...
Click to collapse
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Try this
open sync then at the top chose files then click on DELETE MOBILE DEVICE
see what happens..but post back if you fix it to help other people
yogusmilu said:
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
Click to expand...
Click to collapse
I failed to mention that I've tried the hard reset as well, no luck.
I thought about the same thing Deuse, but there's no mobile device registered, so I'm not able to delete it.
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Looks like your cable is faulty. Try activesync connection through bluetooth (for testing, ofcourse you cant flash from bt ).
parthabhatta said:
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Click to expand...
Click to collapse
It's marked with an "!", will try it on my own pc next time I have it, worked there last time! if not, I'll have to live with