i flashed from SD my eten X650 with the original rom from X500 by a mistake.
is there someone to help me solve this problem.
it can boot now from sd.
BUT
if i press(camera+power+reset0buttons my pc recognize it likeMICROSOFT USB SYNC devise but it can conected with microsoft active sync
please help me and ican pay someone if he make it work again with 50€
bear79 said:
i flashed from SD my eten X650 with the original rom from X500 by a mistake.
is there someone to help me solve this problem.
it can boot now from sd.
BUT
if i press(camera+power+reset0buttons my pc recognize it likeMICROSOFT USB SYNC devise but it can conected with microsoft active sync
please help me and ican pay someone if he make it work again with 50€
Click to expand...
Click to collapse
Just flash it with the rom for the X650 and you'll be back to your old self. The fact that it can still boot is a good thing since apparently you did not brick the device.
when i try too boot my X650 my screen becomes white and nothing hepens.
then i connect it with pc and recognize it.
i thing that i can flash it.
any other solution?
thanks
Flash from your pc then if your pc recognizes it. By pressing camera+power+reset0buttons i'm guessing you are talking about the bootloader.
yes.for bootloader menu i am saing.
how i can boot it from pc?
if you are stuck in bootloader, then your pc will not recgonise the devise for activesync (or for the RUU software), i think you have to use mtty
i think thay mtty is only for HTC or i am wrong?
This is exactly why we are always telling people to read before doing these things, so that they do not mess up their devices.
Anyway, get your device in bootloader mode and connect it to the PC. You must kill Active Sync (I am assuming that you are using Windows XP and not Vista). In order to kill ActiveSync, you must open the Task Manager and kill the processes called rapimgr.exe and wcescomm.exe.
Once you've done that, you must run the upgrade/rom upgrade utility program in your computer and follow the instructions on the screen. [highlight]Please make sure that the rom that you are using is specific for your device.[/highlight] Otherwise, you will brick your device for certain...
Note that upgrade instructions are, under most cases, device specific. Make sure that you follow the instructions in your upgrade precisely. Most rom cooks post either Readme.txt files along with their roms or they post very precise instructions in the forums. What I just gave you here is a very general set of instructions that normally work for most devices. I do not have an Eten (never have), so I am uncertain if these instructions will be useful to you. Follow them under your own discretion. [highlight]I am not responsible for any damage to your device.[/highlight]
Good luck...
it ask me again to connect wiyh active sync
Ignore. was moved
HELP mE please
soo no solution has found
bear79 said:
soo no solution has found
Click to expand...
Click to collapse
Just read my post. If the device is in bootloader, it should not try to connect to activesync, the pc should only see a USB device. Look for a rom upgrade for your phone and look at the upgrade instructions and follow them exactly. Your phone is not bricked, it only needs to be re-flashed.
i have tried that but nothing heppens.
when i try too put it in bootloader menu my sreen becomes white.
is this bricked phone?
Yes if you cannot get into your bootlaoder, it is bricked.
Related
Hi,
I've a little problem.. yesterday the rain shocked my htc p3651..
Today I was able to make a backup (it works 'cause I tried with wm6 emulator).
Now when I turn on my pda I see the RGB screen and:
POLA*** MFG
SPL-2.20.Olinex
CPLD-2
and if there's the MicroSD inserted it tells "No Image File!" for a while.
I tried with hard reset: I held both lower buttons with the stylus in.. then I released the stylus helding buttons.. but no hard reset.
I really don't know what I've to do.. please help me!
Thanx
It sounds like the rain caused your device to short na dump the rom. I would try to reflash your phone with a rom of your choice and see if that works. Make sure that you take the battery off and blow dry it for a while to ensire that it is dried out. Good luck.
Hyden121 said:
It sounds like the rain caused your device to short na dump the rom. I would try to reflash your phone with a rom of your choice and see if that works. Make sure that you take the battery off and blow dry it for a while to ensire that it is dried out. Good luck.
Click to expand...
Click to collapse
Thanx 4 the answer. Please can u tell me a guide for reflashing it? It's the first time and I don't know where I've to begin from..
Well the tri colored screen is the boot loader screen. If you are using Vista then launch windows mobile device center and plug in your phone. Download a rom and launch it. It should hopefully read your device. Then just click next through the rest of the prompts and see if you can get that rom on there. If you are using windows XP then you will need to launch Active Sync. It really is fairly simple after you do it the first time... If your device is not unlocked then you need to fsearch the forums to find out how to unlock it.
Hyden121 said:
Well the tri colored screen is the boot loader screen. If you are using Vista then launch windows mobile device center and plug in your phone. Download a rom and launch it. It should hopefully read your device. Then just click next through the rest of the prompts and see if you can get that rom on there. If you are using windows XP then you will need to launch Active Sync. It really is fairly simple after you do it the first time... If your device is not unlocked then you need to fsearch the forums to find out how to unlock it.
Click to expand...
Click to collapse
Thanx again. I use XP and let me ask to you the last question: is it possible to do it directly from MiniSD?
I know there is a way to flash a rom from the mini sd card but I have never done it. Search the forums. I know I have seen it covered there.
go to xda-wiki and click on polaris. there youll find what your looking for.
I tried.. with 2 or 3 ROMs (original too) but still start with bootloader..
I've done it from MicroSD 'cause USB doesn't work.. does it nees some particular drives? Now is Microsoft USB Sync..
Thanx a lot
so you cant enter bootloader? but you have activesync 4.5 installed on your pc?
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
I think you have been bricked your device...
dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!
I had already done those steps to get no results.
its my badluck.
If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid
I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards
Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,
Mtty is not detecting my device
it says can't open usb port
One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards
have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.
Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards
ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck
noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.
my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail
i cant believe i did this but i have a sprint tp2 and i accidentally install the wrong rom, i installed 1.8b_Sense_2.5_2012_Full, and after the update the phone wont turn on so i cant even do the bootloader. and hard reset either, nothing is responding. is there any way i can get out of this with a working phone?? would the people at sprint be able to help? and please no smart ass comments im really bummed out about this right now
It should be ok if you only install a gsm rom. If you installed a gsm unlocker than it is bricked. Just push the bootloader buttons with the phone off. If it doesn't go to bootloader it is bricked.
i installed the rom but i think the damn thing CAME with the radio unlocker inside the rom. i cant get into bootloader...
please help
If you can't get into bootloader and it wont turn on it is bricked.
Not to hijack the thread, but on the subject of bricking the phone...
I tried to install Hard SPL using SSPL Manual (downloaded from a link on ppcgeeks.com). I ran it from the phone, and the screen blanked as normal, but no USB device was detected after doing so and the manual Hard SPL would not work either.
I tried to reset and remove the battery. The phone will not turn on, will not enter boot loader mode, nothing! EXCEPT for one thing, when I plug in USB now, it is detected as a Qualcomm CDMA Technologies MSM. No driver though (Win 7 or Win XP).
Is there any way to recover from this?
Hi!
Download and install this:
_ftp://up.ppcgeeks.com/Touch%20Pro%202/Stock%20ROMs/RUU_Rhodium_W_Sprint_WWE_1.21.651.3_RS_1.96WF_NV_SPCS_1.42_0430_PRL60652_Ship.exe
I think it help you.
ted2001 said:
Hi!
Download and install this:
_ftp://up.ppcgeeks.com/Touch%20Pro%202/Stock%20ROMs/RUU_Rhodium_W_Sprint_WWE_1.21.651.3_RS_1.96WF_NV_SPCS_1.42_0430_PRL60652_Ship.exe
I think it help you.
Click to expand...
Click to collapse
Hi, I have the exact same issue as the member above. I tryed to go to the ftp site you reccomended, but can't download. Can you please help! I cant sleep or think of anything else. Can't believe I did that to my phone.
go here and then to touch pro 2 stock roms. ftp://up.ppcgeeks.com/
Thanks for the replies.
I can't load the stock ROM since the phone is not recognized by ActiveSync. While you can see it when you connect USB, it isn't actually usuable as there is no driver loaded for it. And many drivers I've tried for it do not work either.
I did try [to install the ROM] though just to make sure there was no magic going on behind the scenes, but no go.
EDIT: Grammer fix
This mode was accidentally entered when I'm trying to boot my htc hd7 and press camera button together with volume up (around 20sec while the phone booting). For your information, my htc hd7 having problem with zune application and my device manager recognize it as unknown devices (yellow exclamation mark).
It was caused when I've sideloading USBModeSwitch.xap and change from ZUNE to DIAG mode. After the phone restarting, the apps has been revoke then i've no chances to install the apps again to fix it back to ZUNE mode.
Now the phone can operate as usual but cannot recognize by zune (yellow exlamation mark in device manager in PC).
The good news is, the phone had recognized by pc when entering this mode. and the devices manager detect the phone under Portable Devices -> Schubert. Can we sideloading apps using this mode? If yes... it was a good news for those having the same problem with me. But the question is.. HOW.
Note: After the incident, I already flash the phone. but still unable to be detected by ZUNE Desktop in normal state. it can operate, can install from market place as usual but cannot sync with zune desktop. Can somebody help me on this? Sorry for my English. You may refer with my attachment for the images and the XAP application.
Note 2: Never try the USBModeSwitch.xap if your phone is not fully unlock or will facing the same problem with me. hope someone can fix this issue. because lot of friends are stuck in this doom.
same problem here....
an hd7 too...
First, are your phones unlocked? I assume they are. Otherwise you wouldn't be able to deploy this USB-whatever.xap.
You may try deploying smth after running WPConnect (Phone has to be connected already). This small consoleapp does some funny stuff with the phone/PC connection. So maybe your devices will be recognized this way.
Best you start WPConnect from commandline, to have a look at the output, which should be smth like "[Devicename] successfuly connected..." or such.
C~
tried it, doesn't help
the phone is not unlocked anymore... that is the problem in my case ;-)
but i was able to install the HTC Diagnostic Drivers...
but i dont know if i can use it to disable Diag-Mode...
And you are not able to re-unlock your phone (via official or Chevron)? Have you tried to unlock after connecting - closing Zune - running WPConnect?
This is just a mere guess, but hey, who knows it maybe work
we cannot lock our devices as neither zune nor WPConnect realize that the phone is connected (because of it is in Diagnostic-Mode)
but thanks for your reply ;-)
Oberoth said:
we cannot lock our devices as neither zune nor WPConnect realize that the phone is connected (because of it is in Diagnostic-Mode)
but thanks for your reply ;-)
Click to expand...
Click to collapse
Yup that's true. I try to used ansar ROM, flash it, but nothing change. I wonder if we can custom a rom and implement the extract file of USBModeswitch.xap to the rom. so that the phone will boot with usbmodeswitch installed in it, using this step, we're able to switch the mode from diag back to zune.
This the final technique might can help for now. For the ROM, i can only break/extract until I've got the 2 OS file:- 2_os.nb.extra (±2.4MB) and the other one is 2_os.nb.payload (±181MB). Ok, until then, I was stuck. if not... we can extract the XAP directly to the OS folder, then repacking back the ROM. the 2_os.nb.payload file was unable to extract to bin file. Error shown:- "no boot partition". Maybe I'm using the old WinMo tools to extract it.
ahhh.... gosh... stuck in this step. any help and guide will be much appreciated.
AzmanIshak said:
Yup that's true. I try to used ansar ROM, flash it, but nothing change. I wonder if we can custom a rom and implement the extract file of USBModeswitch.xap to the rom. so that the phone will boot with usbmodeswitch installed in it, using this step, we're able to switch the mode from diag back to zune.
This the final technique might can help for now. For the ROM, i can only break/extract until I've got the 2 OS file:- 2_os.nb.extra (±2.4MB) and the other one is 2_os.nb.payload (±181MB). Ok, until then, I was stuck. if not... we can extract the XAP directly to the OS folder, then repacking back the ROM. the 2_os.nb.payload file was unable to extract to bin file. Error shown:- "no boot partition". Maybe I'm using the old WinMo tools to extract it.
ahhh.... gosh... stuck in this step. any help and guide will be much appreciated.
Click to expand...
Click to collapse
Hi,
from your writing i can read that you have the needed knowledge to make this thing...
so how long do you think will it take to get the two files...
and if you get these files, how can we flash that ROM without HSPL or SSPL?
thanks for your answer ;-)
our problem is... there's still no kitchen for WP7 (temporary). So.. we have to wait Da_G or Ansar.Ath.Gr work. they might have some tools that can help us. I knew.. lot of our friend already stuck in this mode as well. So... there's no sync with zune for us... no music transfer via usb.. and we have to forget all the thing that we can do using the USB cable except for charging it. lol~ how sick...
yeah...
i can only listen to radio in the morning when i drive to school...
i hate the most of the breakfast-shows
i have another idea instead of waiting for an C-ROM...
but that is only possible with a clean, Chevron-Unlocked and USB-Switch installed WP7 phone...
so nothing personally...
and we need to wait for the update...
the whole clean system would be backed up and could be used for our WP7 devices to get the USBSwitch-App onto our phone (holding camera-key when starting to install backup)
would be great if there is anybody who makes it...
hi
ask the autor of this http://forum.xda-developers.com/showthread.php?t=922000
maybe he can help ,his tool use usbmodeswitch.
im active in his thread too, but he didn't answer at all...
I have actally done this myself sadly the only option I had was to sync all my contacts with Windowslive and reset the HD7 by holding both volume keys while powering it on from a cold boot.
AzmanIshak said:
This mode was accidentally entered when I'm trying to boot my htc hd7 and press camera button together with volume up (around 20sec while the phone booting). For your information, my htc hd7 having problem with zune application and my device manager recognize it as unknown devices (yellow exclamation mark).
It was caused when I've sideloading USBModeSwitch.xap and change from ZUNE to DIAG mode. After the phone restarting, the apps has been revoke then i've no chances to install the apps again to fix it back to ZUNE mode.
Now the phone can operate as usual but cannot recognize by zune (yellow exlamation mark in device manager in PC).
The good news is, the phone had recognized by pc when entering this mode. and the devices manager detect the phone under Portable Devices -> Schubert. Can we sideloading apps using this mode? If yes... it was a good news for those having the same problem with me. But the question is.. HOW.
Note: After the incident, I already flash the phone. but still unable to be detected by ZUNE Desktop in normal state. it can operate, can install from market place as usual but cannot sync with zune desktop. Can somebody help me on this? Sorry for my English. You may refer with my attachment for the images and the XAP application.
Note 2: Never try the USBModeSwitch.xap if your phone is not fully unlock or will facing the same problem with me. hope someone can fix this issue. because lot of friends are stuck in this doom.
Click to expand...
Click to collapse
can you tell me what rom was on the phone and what rom you flashed After you F*****up your phone ?
I want to know what Radio was on it , I think that tool does something with the radio rom on the phone , it could help the flash an older rom using a goldcard with an older radiorom in it.
edit:
maybe it is the spl , try to flash a rom with a lower/higher spl number.
ceesheim said:
can you tell me what rom was on the phone and what rom you flashed After you F*****up your phone ?
I want to know what Radio was on it , I think that tool does something with the radio rom on the phone , it could help the flash an older rom using a goldcard with an older radiorom in it.
edit:
maybe it is the spl , try to flash a rom with a lower/higher spl number.
Click to expand...
Click to collapse
Hi Ceesheim, thanks for reply. I'm not remember my preveous ROM, by the way
currently only RUU_Schubert_hTC_Asia_WWE_1.23.707.01_Radio_5.51.09.06a_22.30.50.09U_Signed_by_ansar that can be flash to my phone.
AzmanIshak said:
Hi Ceesheim, thanks for reply. I'm not remember my preveous ROM, by the way
currently only RUU_Schubert_hTC_Asia_WWE_1.23.707.01_Radio_5.51.09.06a_22.30.50.09U_Signed_by_ansar that can be flash to my phone.
Click to expand...
Click to collapse
thats a modded rom (don't use it)
try this one :
http://forum.xda-developers.com/showthread.php?t=853945
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
xboxmod said:
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
Click to expand...
Click to collapse
ok... will test it now. thanks!
I'll report to you after complete. thanks again~
xboxmod said:
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
Click to expand...
Click to collapse
I already download and install to my PC. but cannot flash to my phone.
Currently the only ROM that my HD7 can flash is with this number: 1.23.707.01
Make a goldcard and then flash it
Sent from my HD7 T9292 using Board Express