The screen on my Kaiser is solid white every time it turns on--either by me pressing the power button or by my phone receiving a call or text. However, if I press the power button twice to turn the screen off then on again, it's normal. I've tried leaving the battery out for ten minutes, hard resetting my phone, flashing back to the last official AT&T WM 6.1 ROM and radio, and flashing to another WM 6.5 ROM (in my sig). Is there anything else I can try? Another SPL?
Related
Hi,
I have upgraded my MDA to NO EVIL ROM Windows mobile 6 version from this forum. Device was working great for couple of weeks. Now suddenly it stopped booting. When I do soft reset the
S.N.E ... Presents screen comes up.
Then HTC Wizard screen comes up
The Touch No Evil screen come up and then it stays at the same screen. It does not respond even to power button now.
The radio light (green light) blinks. The system does not respond to even hard reset.
I am tosed. Please help. Any response to recover from this situation is usefull.
Thanks in advance...
From the sounds of it, something you have installed or configured isn't allowing the phone to finish booting. You basically have 2 choices at this point... Hard Reset or Reflash the phone.
When you say hard reset doesn't work, are you sure you are doing a hard reset? Pull the battery out and let the phone rest for a minute or so. Press the power button a couple of times (yes with the battery out) to discharge any power in the device. Then put the battery back in, and press the top two buttons on either side of the phone (Comm and Record), and while holding those in press and release the power button. After a couple of seconds you should have a black screen with white text asking you about resetting the phone. Press the Send key (the green phone key that you use to answer the phone) and you will have completed the Hard Reset. If you get errors then you need to tell us what they are. If you never get the black screen with white writing then you aren't holding the buttons down correctly.
To reflash the phone, put it in bootloader (press and hold the recorder button while pushing in and releasing the reset button (or while turing the phone on)). Once you get the tri color screen, hook up the USB cord and it should say USB in the lower left. Now you can flash it (even though the phone won't connect to ActiveSync).
Good luck and hope that helps.
Able to reboot
Thanks for the advise. After several tries, was able to hard reset and started booting and working OK.
I have not done any soft reset after this event. What should I look for to correct, if any errors.?. do you recommend that I reflash the ROM?. The only software, I had installed was Microsoft Voice recorder. I have not installed the same after the reboot.
Thanks
ANother issue
Now after resetting, I see my phone getting into vibration mode all the time. Even if I set to ring mode, it will automatically go back to vibration mode after some time. Any idea on how to fix the same?.
Thanks
Hi
My 750v has these quirks
- when i want to put on standby by pressing red button, the screen goes away but lit after several seconds. No matter how may times I press it again it goes away and lit back again. Only when I soft reset, would the screen stay unlit when I press it.
- when I activate the Today screen the touchpad locked message appears. It takes a longer time for the message to go away when when I press the center button.
Mine is stock Palm ROM WM 6.0 from the corporate site. And I don't have a lot of apps on it.
Advise?
Turn your device brightness to 50% or above. It's a well known WM bug....
Hi, I have been flashed TAEL ROM, radio last month. Everything running fine until early of this morning.
I have not do any changes recently.
suddenly this morning I could not turn on the phone from standby. So I soft reset it, right after soft reset, it keep on reboot itself after reach TAEL ROM screen, sometimes after Windows Mobile screen.
I tried to get into bootloader screen but the nothing happened.
the reset button seems like cannot function now.
I press and hold vol down button then press on Reset but phone have no respond at all...
Anyone have experienced this and solved it?
Thank you!!
Try pulling out the battery for a while. That fixes this problem sometimes.
I would try a hard reset, if things do not improve.
Had to do one yesterday and it took me some time to find out how it's done for this phone so if you're not familiar with it here it comes:
1) Turn off the phone (take out battery for 5 sec, then put it back in)
2) Hold volume DOWN button and press the centre of the circle (enter button)
3) While holding those 2 buttons, power up the phone (and keep pressing this combination until you enter into bootloeader)
4) When in bootloader (I normally keep the volume DOWN and Enter button pressed, until I see the message in bootloader saying that in order to hard reset I should press volume UP, or any other key to cancel).
Hope this helps, and remember that you'll loose everything (programs, contacts, SMS, etc) if you do this.
Good luck.
Remove your sim and sd card before doing the hard reset..right?
It's not necessarily REQUIRED, but it is recommended.
Hi,
I think this is a wierd one. I have a Vodafone Touch Pro and it will go into bootloader (strangely by vol down and power button only, so does my other one despite what the internet states), it will even hard reset (which completes) but will not start up on power at all. I push the power button, even hold it down and nothing, not even a vibrate, slight glow from screen, key glow or flashing lights. Phone does not charge, judging by the lack of a glowing ring either.
What I have tried:
Leaving battery out over night
Hard reset
Flashing OEM Vodafone ROM (completed fine)
Tried putting battery back on charge
Tried leaving on charge (battery in and battery out)
Could anyone help me out with this?
I know my old HTC Vox never started up with the slide open, could it be something simple like a stuck switch?
Many thanks,
Tristan
Anyone have any ideas?
So I've had my fuze a little over a year now, no major issues. Used mostly energyroms, but about December time I switched back to a simple non-bloated stock rom for the stability.
Anyway today at work I was texting, and I press the power button to put the phone in standby. And the screen remains on and usable. I tried again and it would not go into standby (power button physically feels normal, it does not feel loose or abnormal.) So i let it sit for a few minutes, then i look at it and a message poped up asking if i wanted to turn the phone off (like as if i was holding the power button)so i press no, then it comes up again a few seconds later and aagain and again. So I soft reset the phone.
The phone resets but takes a LOT longer at the att/htc splashscreen, then it hangs at the htc screen and does not make it to the wimo screen, but instead an error screen saying:
"The device is unable to boot because you have either turned off the device incorrectly or tried to install an applicationa from an untrusted source, press SEND to reset your device or press any other button to cancel..."
I think it went through the hard reset this time because when it restarted it asked to calibrate the screen and install stuff. it resets again sometime after that, still takes forever at the splash screen and comes back up to the error, only this time no matter what button i press it wont go away and boot into wimo. It seems like none of my buttons work (they wont light up now) when i slide out the keyboard, it is not lit up like normally.
And heres the kicker, my only way to turn on/off the phone is to take out/put in the battery. As soon as I pop the battery back in the fuze turns on. Is my phone toast? Ive tried to hard reset and the phone does not reach the bootloader, it goes straight to the splash screen. Same with trying to reflash it from my comp, raphealwrapper cannot find my phone.
I've only recently encountered the exact same problem on my Touch Pro, but stock ROM and everything. As far as I can tell, our power buttons are busted and probably need to be serviced. One of the contacts must be stuck in the 'on' position somewhere inside :\ As a temporary fix, I've been using AEButton Plus and remapped double tap end call key to turn the screen off, and removing the stylus to turn it on.