Treo 750 issue - Palm Treo 750

Hi
My 750v has these quirks
- when i want to put on standby by pressing red button, the screen goes away but lit after several seconds. No matter how may times I press it again it goes away and lit back again. Only when I soft reset, would the screen stay unlit when I press it.
- when I activate the Today screen the touchpad locked message appears. It takes a longer time for the message to go away when when I press the center button.
Mine is stock Palm ROM WM 6.0 from the corporate site. And I don't have a lot of apps on it.
Advise?

Turn your device brightness to 50% or above. It's a well known WM bug....

Related

Help! MY MDA does not boot

Hi,
I have upgraded my MDA to NO EVIL ROM Windows mobile 6 version from this forum. Device was working great for couple of weeks. Now suddenly it stopped booting. When I do soft reset the
S.N.E ... Presents screen comes up.
Then HTC Wizard screen comes up
The Touch No Evil screen come up and then it stays at the same screen. It does not respond even to power button now.
The radio light (green light) blinks. The system does not respond to even hard reset.
I am tosed. Please help. Any response to recover from this situation is usefull.
Thanks in advance...
From the sounds of it, something you have installed or configured isn't allowing the phone to finish booting. You basically have 2 choices at this point... Hard Reset or Reflash the phone.
When you say hard reset doesn't work, are you sure you are doing a hard reset? Pull the battery out and let the phone rest for a minute or so. Press the power button a couple of times (yes with the battery out) to discharge any power in the device. Then put the battery back in, and press the top two buttons on either side of the phone (Comm and Record), and while holding those in press and release the power button. After a couple of seconds you should have a black screen with white text asking you about resetting the phone. Press the Send key (the green phone key that you use to answer the phone) and you will have completed the Hard Reset. If you get errors then you need to tell us what they are. If you never get the black screen with white writing then you aren't holding the buttons down correctly.
To reflash the phone, put it in bootloader (press and hold the recorder button while pushing in and releasing the reset button (or while turing the phone on)). Once you get the tri color screen, hook up the USB cord and it should say USB in the lower left. Now you can flash it (even though the phone won't connect to ActiveSync).
Good luck and hope that helps.
Able to reboot
Thanks for the advise. After several tries, was able to hard reset and started booting and working OK.
I have not done any soft reset after this event. What should I look for to correct, if any errors.?. do you recommend that I reflash the ROM?. The only software, I had installed was Microsoft Voice recorder. I have not installed the same after the reboot.
Thanks
ANother issue
Now after resetting, I see my phone getting into vibration mode all the time. Even if I set to ring mode, it will automatically go back to vibration mode after some time. Any idea on how to fix the same?.
Thanks

White screen

The screen on my Kaiser is solid white every time it turns on--either by me pressing the power button or by my phone receiving a call or text. However, if I press the power button twice to turn the screen off then on again, it's normal. I've tried leaving the battery out for ten minutes, hard resetting my phone, flashing back to the last official AT&T WM 6.1 ROM and radio, and flashing to another WM 6.5 ROM (in my sig). Is there anything else I can try? Another SPL?

broken fuze. powers on as soon as battery is popped in

So I've had my fuze a little over a year now, no major issues. Used mostly energyroms, but about December time I switched back to a simple non-bloated stock rom for the stability.
Anyway today at work I was texting, and I press the power button to put the phone in standby. And the screen remains on and usable. I tried again and it would not go into standby (power button physically feels normal, it does not feel loose or abnormal.) So i let it sit for a few minutes, then i look at it and a message poped up asking if i wanted to turn the phone off (like as if i was holding the power button)so i press no, then it comes up again a few seconds later and aagain and again. So I soft reset the phone.
The phone resets but takes a LOT longer at the att/htc splashscreen, then it hangs at the htc screen and does not make it to the wimo screen, but instead an error screen saying:
"The device is unable to boot because you have either turned off the device incorrectly or tried to install an applicationa from an untrusted source, press SEND to reset your device or press any other button to cancel..."
I think it went through the hard reset this time because when it restarted it asked to calibrate the screen and install stuff. it resets again sometime after that, still takes forever at the splash screen and comes back up to the error, only this time no matter what button i press it wont go away and boot into wimo. It seems like none of my buttons work (they wont light up now) when i slide out the keyboard, it is not lit up like normally.
And heres the kicker, my only way to turn on/off the phone is to take out/put in the battery. As soon as I pop the battery back in the fuze turns on. Is my phone toast? Ive tried to hard reset and the phone does not reach the bootloader, it goes straight to the splash screen. Same with trying to reflash it from my comp, raphealwrapper cannot find my phone.
I've only recently encountered the exact same problem on my Touch Pro, but stock ROM and everything. As far as I can tell, our power buttons are busted and probably need to be serviced. One of the contacts must be stuck in the 'on' position somewhere inside :\ As a temporary fix, I've been using AEButton Plus and remapped double tap end call key to turn the screen off, and removing the stylus to turn it on.

Touch screen problem, like "auto-touch"

Hi, i bought Asus TF300T 1 month ago in Taiwan.
When I turn on the screen by pressing Power button, I use it 5-10 minute and the screen has some point "auto-touch", example: I reading book and Home button on Notification bar was touch, like someone try touch that button continuous (And more point in the screen have same problem). I must press Power button again to turn off the screen then try press 1 more to turn on it. And use 5-10 minute, problem return, again.
I tried hard reset it but it not change.
Any idea? I'm so sad and worry.

Nexus Won't Boot Up

Help! My nexus 5 won't turn on after only having it for about a year now.. It's not a boot loop!
Here's what's happening:
-My phone boots up to the google sign and then the 4 moving color dots... It never gets past this screen.
-If the phone is plugged in, the phone will continue this looping process all night.
-If the phone is not plugged in, it will only occur twice when the power button is pushed.
-If I attempt to access the bootloader, I only see the screen for a split second until the google screen reappears and the loop begins all over again.
-I can get past the 4 dot screen by repeatedly hitting the power button on an interval of roughly once per second.
-If I do this, the next screen to appear is the "Android is upgrading.." "optimizing 0 out of 130 apps."
-This screen will not progress through all 130 apps however, unless i keep pressing the power button at the interval of roughly once per second.
I used to successfully make it through the start up process this way and be okay for the day, but now my phone will shut off once the home screen is reached. It seems to me that the power button was a bit too sensitive, but I took the phone apart and it is working fine. I did drop my, which cracked the screen, about a month ago. About a week ago is when the problems began to occur. The insides look good though, just the screen which is cracked. Any ideas would be greatly appreciated!
I'm trying to hold out for the Nexus 5 (2015)!
Dead power button it is.
In Indian LG service centers they replace out of warranty handset's power button for 330inr roughly 5usd.
I had the exact problem and thought is discarding the phone, but the repair fixed it.
Thanks, I'll look into this. Maybe try to do it myself real quick.
It's not easy to replace yourself, ad the button is soldered to the board. Best give it to a pro lab.
Bang it on a hard surface like a table. That is a temporary fix when my power button starts to act up. You can try hitting it on the palm of your hand, but that doesn't really jar it enough.

Categories

Resources