help to resurrect my axim x50mid
Hello folks, that's fine with you, then ....
Today I upgrade my axim x50 mid, was trying to update to wm5, but does not succeed in the process, I found a rom DiMa_K_A01_X50_WM5_EN.nb0, and changed her name to DiMa_B_A01_X50_WM5_EN.nb0 crc also like ...
The same finished the installation process and asked a hardreset, did the hard and then it was only with the black screen ... I tried every way to revive my toy .... but without success, then come to you asking for help resurrects him.
sorry my english bad.
Related
Hello everybody!!!
I need help with my Himalaya... Tried to upgrade it to WM5, successful for a while but after a soft reset, it wont boot up properly. It stays stuck on the Windows Mobile boot screen, with both the bluetooth and power/signal light turning on/off alternately. Hard resetting it does not help, the same symptoms are still happening. I had to reinstall the WM5 ROM several times but the same problem now occurs everytime I have to soft reset the unit. I had to downgrade to wm2003, ROM 1.72.00WWE, Radio v1.17.00, extROM v1.72.181.
Can anybody help me on this? Thanks!
how is it possible to update from wm2003 to wm2005?
www.buzzdev.net
get a rom and
a howto is in the zip
Recover crashed device.
seph1978 said:
Hello everybody!!!
I need help with my Himalaya... Tried to upgrade it to WM5, successful for a while but after a soft reset, it wont boot up properly. It stays stuck on the Windows Mobile boot screen, with both the bluetooth and power/signal light turning on/off alternately. Hard resetting it does not help, the same symptoms are still happening. I had to reinstall the WM5 ROM several times but the same problem now occurs everytime I have to soft reset the unit. I had to downgrade to wm2003, ROM 1.72.00WWE, Radio v1.17.00, extROM v1.72.181.
Can anybody help me on this? Thanks!
Click to expand...
Click to collapse
After upgrade, ensure you clear registry and format the storage. You may try to redo this by following the instructions in the last part of the installation document, as pasted below:
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
Click to expand...
Click to collapse
Also be aware that many backup software can corrupt an installation after recovery, even those that have a "Upgrade or Migration" feature. It is best to use PPCBckpContacts to restore your contacts and to use SMS BackupSoftware for your sms's, both can be found on this forum and both use standard databases instead of proprietary formats that could corrupt the WM5 databases.
on topic: i will have to bookmark this page in case i get the same problem when i upgrade
off topic:thanx rudega, u dnt know how amazed i am...just signed up to the forum cus i wanted to get the WM6 theme for my xda, then it said i needed wm5 so i cried abit, the i saw this post and laughed ha u cant update O2 website havent said anything...then i looked around this whole forum and realised i could. this is amazing really pleased. no more old looking 2003.
that post i wrote ealier must be amusing to all since everyone here knows u can upgrade to wm2005. i kinda regret it being my 1st ever post here.
thnx again. (hope this upgrade business isn't to dificult to do)
wow! lots of great responses to my thread... thanks a lot guys! i will try all the things that you instructed here. i will report what happens... you guys are the best!!!
it is working as of now!!! yahoo! thanks a lot pneuma! i've decided to use chandra shenkar's ROM... it IS a lot faster than the original WM5 that i've previously used. will give a heads up if things go wrong again!
hi i hav KROME NAVIGATOR wit win 2003 ROM version 1.72.00wwe radio version 1.17.00 well i hav tried to upgrade it manny times to wm05 & also 2003se but it gives error.. i used unlocker software from here in dowloads but it says its already unlocked .. plz any1 help me how to flash wm05 on ma PDA... i got it somtime ago.. i also hav a spv c550 smartphone too which i did upgrade to wm059 i used super CID tool to unlock the ROM for Flashin, but i can't get through this one plz help.. it be very helpfull... thanks in advance...
"well i hav tried to upgrade it manny times to wm05 & also 2003se but it gives error"
you may want to elaborate a bit on that
sheesh
Just did a soft reset and the problem just happened again. something must be wrong with my hardware! i had to do a hard reset to get back up again. comments anyone?
wow i remember this post i made month ago. since then my phone broke, was stuck with an acient nokia, no camera, not even a colour screen. luckily im back with a new windows mobile phone. anyway no one is gonna read this, but i thought i should take a trip down memory lane
First off I'd like to apologize for what must seem like a duplication of a thousand other "stuck in boot loader" threads, but I've got what appears to be a fairly unique situation here and none of the fixes I've found searching the forum have worked for me.
Yesterday I flashed Dutty's WM6.1 ROM using JumpSPL, everything went fine. Today I went to install one of Niki's radios using JumpSPL again, but it got stuck at 99%. I went through the recovery process (several times) and each time after that got stuck at 0%. I've tried soft and hard resets, every time it comes back to the tricolor boot loader. MTTY doesn't give me the USB port option, even if I disable any and all tasks related to Mobile Device Center. Stock AT&T ROM won't load, says "This update utility cannot be used for your PDA phone." I can't flash HardSPL, after I hit enter it doesn't do anything. I tried the Vista fix available on Modaco, but it's not compatible with 64-bit Vista so I'm SOL there too. I'm really at wits end here, could someone please point me in the right direction? I've read time and time again here that as long as you still get the tricolor screen your phone is not bricked, but I seem to be all out of options and nothing has helped.
The boot screen displays the following:
RUUNBH (Top right corner)
KAIS1*0
SPL-1.56.0000
CPLD-8
Please, any and all help would be greatly appreciated!
I don't believe JumpSPL is intended for radio flashing. Flash HardSPL and reflash with a shipped AT&T ROM.
I can't flash HardSPL for some reason, when I press enter in the prompt it brings up nothing happens.
Good job there slick! Did you purposefully ignore all the posts about safely flashing your device?
If you don't mind a little berating & a ton of sarcasm, I may be compelled to take an interest in helping you to fix the device (or to see how badly you've f'd it up & if it can be salvaged at least). Anyway, find me on MSN IM if you want & I'll walk you thru the steps for diagnostics & if possible, recovery.
You'll have to promise not to rush into doing any more stupid things though.
MSN/Live IM: ([email protected])
Yeah, yeah, gung ho, help the newbie, man this is getting old.
for I friend
Hi there ...
a friend of my has a same problem with his Vodafone VPA compact V, can I give him your hotmail ?
Or can you my little tutorial ?
thanks in advance .
Srdjank
T- Mobile MDA Vario
owner , when I am big I will have Tytn II
Managed to get it straightened out, for some reason MTTY 1.42 wasn't working properly with my system but 1.16 did the trick- Rebooted through there and flashed HardSPL then loaded my ROM without a hitch. Thank you everyone for being so responsive and helpful!
srdjank said:
Hi there ...
a friend of my has a same problem with his Vodafone VPA compact V, can I give him your hotmail ?
Or can you my little tutorial ?
thanks in advance .
Srdjank
T- Mobile MDA Vario
owner , when I am big I will have Tytn II
Click to expand...
Click to collapse
Ahhh, one more staisfied customer! Glad I could help out srdjank. Just remember that you can't treat a Kaiser like it's a Wizard. Similar yes, but there are different processes for safely flashing.
So far I've seen that Flashing Radios with JumpSPL is a sure recipe for bad memory blocks. Always, ALWAYS, HardSPL!
i also had the same problem when i tried to sim unlock my mda vario iii in progress screen the progress stuck at 95%. i would appreciate any help to recover the phone. thanks in advance
Hi!
To upgrade my i-mate JAMin from WM5 to WM6.5 I spent several hours to find out how to do.
This forum is very confusing for me.
I was not able to find out what should be done (step by step).
I know, I'm not an expert. I just want to upgrade my phone and use it again - hopefully without troubles.
Can anybody give me a hint in a clear and brief way?
Thank you in advance.
read carefully
i can give you my own guidelines but these guys made better ones already.. just need to read carefully
http://forum.xda-developers.com/showthread.php?t=350033
*skip the procedure 3 and 4 if your ROM has nk.nbf filename already
heres another one if you you need to recover your old device just in case you fail upgrading...
http://forum.xda-developers.com/showthread.php?t=310452
http://forum.xda-developers.com/showthread.php?t=353547
got errors before starting to flash? read the attached file...
thanks to owners of these posts!
hi marekPLPH, thank you for your information. I finished the upgrade successfully few minutes ago. Unfortunately there seams to be some problems (performance, refreshing the display etc).
I'll have a look within this user-platform here to find out how to downgrade from WM6.1 to WM5.
did you hard rest your device? com+cam button+soft reset button?
Hello,
sorry for my bad english
I have a problem with the Qtek S200, it bags every day. I recently installed romProphetManila2D again, I tried after that, with hard reset, but still buging. Do i re-install the same ROM, or what to do? I have Windows 6.1, G4 model.
Thank you
Did you do a HardSPL before flashing the rom
If you have not already done so have a deep read of the Prophet Wiki page as this will give you a lot of usefull info with regards to flashing
Hi guys
When i turn on my smartphone, it`s hang on splash screen. I was try to install Orange ROM and many other and always pops error 279 during upload ROM to device. I could make GoldCard, but i can`t second device with Windows Mobile and i don`t know how to read CID from my memory card in any other way. Each attempt update to new ROM (Ship) via micro-sd ends: "invalid certyficate". Do you have some ideas ???
I`m sorry for my bad english
Please, help me
if someone could help me?
You wrote, what you try update with an Orange ROM. Was it Shiped ROM?
Try download this one and try again. If it doesn't help, then i have no idea at this moment...
RUU_Vox_ORANGE_UK_1.35.61.1_4.1.13.60_03.18.90_Ship.exe
dear all good folks here-getting vox aka s710 in a couple of days-clueless about winmo.
anyone can pl suggest where to start n what all to do???have read a lot of stuff on this thread-most of it going above me since never used a winmobile.hence help in all forms welcome.
thanx.