Hi,
I tried to upgrade my Qtek S200 with the newest ROM release from PdaMobiz (the 16M pooling page one), but encountered some problems...
It's a Portuguese TMN Qtek (or at least it displays the operator logo when started), although the software is in English.
IPL is 2.09 and SPL is 2.15...
However, after upgrading it, it kept displaying the Operator logo with IPL and SPL, and freezed, so it never worked. When I tried to revert it, I wasn't able to do it, because every time I try to install a different ROM (all of them for the G3 device) it just installs the new ROM, and then goes to that screen and freezes...
It never gave me any error during the upgrading/downgrading, because when it checks the version of the ROM, it displays no information, so it just says that is going to replace the inexistant version with the new one...
Is there a step a missed (I didn't put it in bootloader mode before doing the first upgrade, but I had already done that before with other ROMs and it worked fine...)?
Now I'm stuck without knowing if I should have done an unlock CID before upgrading it, or if there is another steped I missed... Please help me out...
Thanks in advance,
Nuno
Tried this?
Read this in one of the threads and it solved his problem:
Extract the rom file you are using to flash your phone, to a folder on your pc, than Extract the file i attached ("ROMUpdateUtility-NoVendorID.zip") into this folder. than connect your phone to pc and double click on "ROMUpdateUtility-NoVendorID.exe".
I personally have not tried it, but I downloaded the prog just in case, Hope it helps.
Now it gives me an error...
Hi,
Just tried what you advised, but now it jusk keeps giving me the error 208, which is supposed to happen because I have other programs open on my computer... Tried rebooting, closing most aplications with task manager, and still it doesn't work.
Also tried to downgrade to lower ROM upgrade, but it gives me the error that I can't downgrade, only upgrade...
When I upgrade it with AKU 2.3, it goes all the way through the upgrade, and then when it reboots, it just keeps giving me the operator logo screen with the version info on the display.
If I try to reboot to bootloader mode, I'm not able, the only way to do it is by removing the battery...
I'm probably still doing something I shouldn't... It should be able to work the downgrade utility...
Anyone can help?
Thanks,
Nuno
Try this rom:
ftp://xda:[email protected]_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip
It shoud be ok.
If your prophet has spl end up with 2.xx.0001 check at
ftp://xda:[email protected]/Uploads/Prophet/
find out the rom which can solve for SPL 2.xx.0001.
Good luck
Thanks Chan! Problem solved!
I was starting to review all my steps ir order to see what I could have done wrong...
Would you advise me to upgrade now to the PDAMobiz latest ROM (the one with the biggest pooling page)?
Thanks again.
Nuno
1. Unlock cid
Since your prophet spl is 2.15, you have to follow this step.
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437
From file you can get from ftp://xda:[email protected]/Uploads/Prophet/
Your PC has to connect to network or internet (to have ip address), becuase in that script use ping command for delay 4 seconds.
It's just downgrade and unlock cid.
You may verify if cid unlocked, by backup rom to sd card. (use romupdate.exe with r2sd all command, check at wiki)
2. Upgrade to official rom
ftp://xda:[email protected]_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip
3. Upgade to pdamobiz, I suggest you to upgrade 12 Mb pagepool version. (even 8 mb version is ok). Because 16 mb has smallest ram space.
Good luck
All solved!
Again,
Thank you very much for your help!
After some tries, upgrading, downgrading, upgrading again, etc, I finally got it, so now its running the PDAMobiz version, which by the way, seems great so far!
Next time I'll come to you directly and then try to make things on my own...
Thanks again!
Nuno Eça
Hello , I am owner of imate kjam unlocked phone.
My IPL / SPL ver is 2.16.
MY GSM ver is 02.07.10.
My OS ver is2.16.9.1.
I cooked the Crossbow_Reloaded_1.7_Final using core pro.
It completed 100% ok but when i restart my phone the OS its the same.
What i am doing wrong ?
I followed all the instructions step by step without having any problem.The only error i get its when the phone starts up after the upgrade when its installed the programs i get the error \windows\autoconfig.exe does not exist.
Please help me.
Thanks
i had the same problem any ideas?
Your Phone is CIDunlocked. You need to be CIDunlocked b4 you can upload the Rom Properly
Qtek s200 (G3) with original rom, update to radio rom 2.69.21, works fine.
Next step, install RUU_Prophet_220734_2207114_024721_NVID and after Prophet_4.0.0.0.4S_PV, no problem, all ok.
Now all update (IPL 2.20, return to RUU_Prophet_220734_2207114_024721_NVID for install PV_4.0.0.0.5a_Cross) don't work! When launch the .exe file and enter in the bootloader appears error 260: unable to connect. Recovery not necessary, after put out the battery the qtek run normally.
Restart pc but same problem.
I have tried to install directly the rom PV_4.0.0.0.5a_Cross and it works, but if I try launch IPL 2.20 or RUU_Prophet_220734_2207114_024721_NVID same problem, error 260!
Help me pls^^
PS: sorry for bad english, I hope you have understood
Hi, Please any one can help me. I have HTC TYTN II with Windows 6.1 but now i want to install Windows 6.0. I hve also tried to install HARD SPL but it gives after 1%. but whe i try to boot it with Jump Spl then it gives error after 15%. So, any one can help me.
aditya4ibm said:
Hi, Please any one can help me. I have HTC TYTN II with Windows 6.1 but now i want to install Windows 6.0. I hve also tried to install HARD SPL but it gives after 1%. but whe i try to boot it with Jump Spl then it gives error after 15%. So, any one can help me.
Click to expand...
Click to collapse
Try downgrading to your providers official 6.0(Orange/at&t/HTC) then hardSPL, i read somewhere it works better on WiMo 6.0.
Don't Work
I hve try to downgrade back to Windows 6.0 but after 15 % it gives error i.e. Invalid Vendor ID. I hve downgrade with jump spl and if i directly downgrade with Orginial HTC or At & T then after 0 % it gives same Update Error.
Have you downloaded the correct official ROM for your device?
aditya4ibm said:
I hve try to downgrade back to Windows 6.0 but after 15 % it gives error i.e. Invalid Vendor ID. I hve downgrade with jump spl and if i directly downgrade with Orginial HTC or At & T then after 0 % it gives same Update Error.
Click to expand...
Click to collapse
Doubt
How should i Know which is my correct ROM and from where i can download bcoz i hve downloaded from this website only but on HTC official website there is only 6.1 version not 6.0 so plz help me. I want this in English lang.
Hi,
I've got two TREO750 devices. Following the same procedure I've updated both to WM6.5: from 5 to 6.1 to 6.5. The OS and FW versions are the same. Weird enough the software version of the devices are different: one uses TREO750-2.27 while the other is still on TREO750-1.15.
A closer look shows that the full 6.1 image flashes all parts of the software successfully (according to the update screen). So it *seems* to work but is not.
Any clues about how to fix this? Thanks for your help!
jeroengsm said:
Hi,
I've got two TREO750 devices. Following the same procedure I've updated both to WM6.5: from 5 to 6.1 to 6.5. The OS and FW versions are the same. Weird enough the software version of the devices are different: one uses TREO750-2.27 while the other is still on TREO750-1.15.
A closer look shows that the full 6.1 image flashes all parts of the software successfully (according to the update screen). So it *seems* to work but is not.
Any clues about how to fix this? Thanks for your help!
Click to expand...
Click to collapse
did you update the HSPL on the device before updating the rom ??
after you update with the Hard spl then you can flash with any ROM, This thread hspl ~ http://forum.xda-developers.com/showthread.php?t=334100
Hakim Rahman said:
did you update the HSPL on the device before updating the rom ??
after you update with the Hard spl then you can flash with any ROM, This thread hspl ~ http://forum.xda-developers.com/showthread.php?t=334100
Click to expand...
Click to collapse
The original poster would not have been able to flash custom ROMs without flashing the HSPL
The problem is the method of flashing, either through USB or MiniSD. Flashing through USB using Palm's Desktop Updater program is the only way for the software version to update itself. When flashing through MiniSD the Software Version cannot update due to the lack of Palm's payload file.