Database Info

Any problem using Mail2Web lately?

Hi,
Just to check anyone facing problem using Mail2Web lately especially this week?
On my side I'm having problem synching my set to Mail2Web
Thanks

RE
Sorry, I mean using 3G/GPRS?
Thanks

Mail2Web
possibly check yr settings in Active Sync, sometimes the schedule gets mixed up by synciing with yr PC,....btw, is the 'heartbeat' interval with Mail2Web still at 30 seconds, in other words is your phone sending and receiving data every 30 secs ? Mine was getting data 'heartbeats' continuously which was killing my battery and my data usage was 6kb/minute, just for the heartbeat, regardless of my registry settings. I've switched to another exchange server, and it uses 4kb per HOUR, and battery life not affected at all !!!!

YES YES YES
I am glad it is not only me. Mine started working again 5 minutes ago, but I don't know if it is something I did, or a host file I made with the ip address in it. I was always able to sync over wifi though. Maybe cingular DNS lost them.

FOSA said:
Just to check anyone facing problem using Mail2Web lately especially this week?
Click to expand...
Click to collapse
Yes, since yesterday no sync via GPRS is possible (o2 Germany).
With wifi via my home cable connection syncing is possible.
When using https://mobile.exchange.mail2web.com in Pocket IE via GPRS I get a certificate warning and after that a login page with a cisco logo, http-connections work fine.
Unfortunately I need a secure connection for active sync :-(

Certificates
That makes sense, that is what the error code points to. Anyone else up and running? What ever it was, I am glad it is fixed.

there is a problem.....I confirm...tried syncing with 4 differrent operators..every time got the error message " Sync cannot be com,pleted.Try again Later" :shock:

I can't sync via gprs either.
I'm on T-Mobile's network in the USA. I can surf the web via GPRS, but syncing via activesync and mail2web is not working via GPRS. Certificate error, which means its an issue on their end...
It IS working via any WiFi connection though...

...wow...
I submitted a trouble ticket at http://services.mail2web.com/About/Contact/
I used "mail2web exchange email" in the subject drop down box.
They replied w/n 10 minutes...!!! Thats better than my Verizon, T-Mobile and Direct TV customer service...and I PAY for those...!
The message:
"Greetings,
Please try doing a hard reboot of your device, by powering your device
off and then on again.
If you are using SSL with your account, please try then turning off your
SSL in your device and sync with the severs, then turn SSL back on and
try to sync again.
If this does not help, please verify that the time and date settings on
your device are correct, as this can also cause an issue when using SSL.
If you continue to experience difficulties syncing your device with your
account, please let me know and I will look in to the issue further.
If you need any further assistance, please do not hesitate to contact
our 24/7 support team at [email protected].
Thank you for choosing mail2web.com!
Regards,
Marya
Customer Support"

...and wow...it worked...!
Try turning OFF the SSL option in your Active Sync Exchange options. Then hit the sync button.
I feel bad, like I should be paying for this...lol...its a rare thing that a CRS over email can INSTANTLY solve a tech issue for me...!
Gotta give em credit for this one...
I am still having an SSL email issue and they are looking into it...but I dont have an issue w/ sending non-ssl email for a few days...
Give it a try...

Specific Steps:
Go to your Active Sync Screen, then:
-- Menu
-- Configure Server
-- UN-CHECK the "this server requires an encrypted (SSL) connection" box
-- dismiss the password warning if you get one
-- Next, then re-enter your password (removing the SSL kills your password)
-- Keep hitting "next" then "finish"
-- Hit the "sync" button
This worked for me. I got my full gprs syncing back...
Again, hats off to them...

Doesn't work for me. Do you use GPRS?

Sync without SSL doesnt work either
Hi, urksaddy
Are you using SSL to synconize? Because, if I swith to Sync without SSL, the active sync shows that the sync couldn't reach the Server and an error code of 80072f78 is given. What server and Domain did you use for the sync without SSL?
thanks in advance.

No SSL
Mine is working without SSL only, switching it back on does not let it sync.

Doesn't work for me either, because my O2-Wap-Flatrate in Germany needs SSL-Connection!
The MS-Support-Code is 0x80072F17

Re: Mail2Web
kashortie said:
possibly check yr settings in Active Sync, sometimes the schedule gets mixed up by synciing with yr PC,....btw, is the 'heartbeat' interval with Mail2Web still at 30 seconds, in other words is your phone sending and receiving data every 30 secs ? Mine was getting data 'heartbeats' continuously which was killing my battery and my data usage was 6kb/minute, just for the heartbeat, regardless of my registry settings. I've switched to another exchange server, and it uses 4kb per HOUR, and battery life not affected at all !!!!
Click to expand...
Click to collapse
What exchange server did you switch to? always looking for an alternative.
thanks,

Direct Push mail
I eventually unwillingly switched from Mail2Web because of the heartbeat interval ( possibly to do with the firewall settings at their server ) the device/server connection was pulsing every 30 secs, using data in ídle'mode and draining my battery. Ï mailed them often and they couldn't/wouldn't resolve it ( but I agree, they always reply fast, !! ) 4Smartphone is an alternative, althought there is a U$ 3.99 per month fee, I calculated it to be cheaper than the "ïdle"data cost per month with Mail2Web. (2kb every 30 secs adds up if you're connected 24/7 !! ) and i'm not on an unlimited plan ! Battery life is also a big issue for me when i'm "on the road". Interesting off topic, for anyone using a non-windows device, push mail is coming to 'normal' mobile phones. Search net for Tricastmedia and/or "Alwayssend" due July 06

thanks for the info, I keep hoping Mail2web will resolve the heartbeat issue, however they seem happy the way it is.

i have mail2web and got no problems connecting.
HOWEVER, my battery life has decreased dramatically once I started using the service. How do I know the pulse interval?
Also, i really dont know if this is an issue with activesync or with mail2web, but sometimes it takes FOREVER to get an email. Sometimes more than FIVE minutes. this way its even more effective to turn on automatic check every five minutes on outlook. Its really not push at all!
I used to have "chatter mail" on my treo 650, and any account that supports IMAP idle (a LOT of providers support it, many of them free) makes it true push. It would take, on everage, 2 to 6 seconds to receive an email. Now THATS push!

urksaddy said:
Specific Steps:
Go to your Active Sync Screen, then:
-- Menu
-- Configure Server
-- UN-CHECK the "this server requires an encrypted (SSL) connection" box
-- dismiss the password warning if you get one
-- Next, then re-enter your password (removing the SSL kills your password)
-- Keep hitting "next" then "finish"
-- Hit the "sync" button
This worked for me. I got my full gprs syncing back...
Again, hats off to them...
Click to expand...
Click to collapse
Thanks your information , when I took off SSL it work fine.

[SOLVED] Exchange not Syncing Over the Air on All 6.1 ROMs

The Problem: I cannot get Exchange to sync correctly when using any 6.1 ROMs.
AT&T Tilt
AT&T SIM
Exchange 2003
Radio: 1.58.26.20
I really need to be able to Exchange sync in order to accomplish my job. From reading though the many 6.1 threads and searching around, I have found that people seem to be occasionally running into this problem, but there hasn't been any resolutions mentioned yet. The problem for me is that synchronization will not occur in ActiveSync. At one point, it would sync my contacts even though it said the sync failed. Others have reported that it will sync contacts and calendar but not email.
The Active Sync error code that I get after flashing a new 6.1 ROM and setting up Exchange the normal way is:
Result: Synchronization could not be completed. Try again later.
Support Code: 0x80830003
Here is a list of things that I have tried so far from searching and asking around that did not work:
1. Didn't work: Installing "remove hidden proxy" .cabs.
2. Didn't work: "What, exactly, are you having issues with? It's not an Exchange 2k3 incompatibility, as mine is synching fine. I did have to go into Settings > Connections > USB and turn off advanced network capabilities, though."
http://forum.xda-developers.com/showpost.php?p=1940649&postcount=1155
3. Verify the following Exchange setting (already checked): "On the Exchange server, launch Internet Services Manager. Right click on the Microsoft-Server-ActiveSync virtual directory and choose Properties. Select the Directory Security tab. Click the Edit button in the Secure Communications section and select the option to 'Ignore client certificates.'"
http://download.microsoft.com/downl...ices-Deploying_Microsoft_Mobile_Messaging.doc
4. Verify the following Exchange setting (not running Exchange 2007): "I also had trouble syncing with Exchange. I run Exchange 2007 and had to enable the option to allow the enrolment of non-supported devices in my ActiveSync policy. With WM5.0 or 6.0 it always worked flawlessly."
http://forum.xda-developers.com/showpost.php?p=1938858&postcount=1025
5: After trying kewlair's suggestion:
"The first issue I had was the initial setup. I set up my account properly, but ActiveSync would report that it cannot sync at this time. I knew that I had to uncheck the Use Proxy for this Connection option to solve this issue, but I couldn't find where to get to that setting for the MEdia Net connection that was being used. I finally found it in Settings -> Connections -> Advanced Tab, then tap the Select Networks button and where it says "Programs that automatically connect..." select MEdia Net instead of My ISP and then you can tap the Edit... button and remove the proxy server selection."
http://forum.xda-developers.com/showpost.php?p=1957501&postcount=3
...attempting to force a sync gives this. I also tried changing "Programs that automatically connect..." to My ISP with the same result:
ActiveSync tries to connect using either MEdia Net or My ISP and then says:
"Cannot Connect
Dialed: Cannot connect for an unknown reason. To check your connection settings and change them if needed, tap Settings. If the problem continues, reset your mobile device according to your manufacturer's documentation and try again."
ActiveSync Reports: "Waiting for network"

Right i am pissed so i might be being a ****, but, it would help if you told us
a) what version of exchange you are running.
b) whether you are using ssl to sync with the server
c) whether you are talking about syncing when connected to the pc, over gprs or such, or both.
Rob

Yeah, I have noticed some issues as well. I'm using dutty's official 6.1 release.
The first issue I had was the initial setup. I set up my account properly, but ActiveSync would report that it cannot sync at this time. I knew that I had to uncheck the Use Proxy for this Connection option to solve this issue, but I couldn't find where to get to that setting for the MEdia Net connection that was being used. I finally found it in Settings -> Connections -> Advanced Tab, then tap the Select Networks button and where it says "Programs that automatically connect..." select MEdia Net instead of My ISP and then you can tap the Edit... button and remove the proxy server selection.
The second issue I have found is that after a while (not sure on specific time) ActiveSync just seems to stop working, almost as if it is hung up. When I go to the ActiveSync window and tap Sync, it does absolutely nothing. Basically the only way i've found to get it to start working again is doing a soft reset.
Hopefully this will help you or other people out, because it took me FOREVER to figure this out. I am curious if anybody else is having problems with ActiveSync stopping responding with 6.1 also.

Same here
Hello,
I am having the same problem here.
I am using DCS 1.5 and windows Vista (Windows Mobilde Device Center). It has been working beautifully for a week..
But now I cannot connect the device to my computer through USB. When I do the charge led is on, but the device is not seen by vista.
I checked off "enable advanced network functionnality" in the USB to PC settings.... But nada!
Any help from otehrs would be appreciated.
Juju

I'm sorry, I might not have been clear. ActiveSync on the device hangs up, not on my computer. I haven't had any issues with ActiveSync on my computer so I think this is a different issue.

rjefferis said:
Right i am pissed so i might be being a ****, but, it would help if you told us
a) what version of exchange you are running. Exchange 2003
b) whether you are using ssl to sync with the server. No SSL.
c) whether you are talking about syncing when connected to the pc, over gprs or such, or both. The PC sync works fine, but over the air it does not.
Rob
Click to expand...
Click to collapse
See answers.

kewlair said:
Yeah, I have noticed some issues as well. I'm using dutty's official 6.1 release.
The first issue I had was the initial setup. I set up my account properly, but ActiveSync would report that it cannot sync at this time. I knew that I had to uncheck the Use Proxy for this Connection option to solve this issue, but I couldn't find where to get to that setting for the MEdia Net connection that was being used. I finally found it in Settings -> Connections -> Advanced Tab, then tap the Select Networks button and where it says "Programs that automatically connect..." select MEdia Net instead of My ISP and then you can tap the Edit... button and remove the proxy server selection.
The second issue I have found is that after a while (not sure on specific time) ActiveSync just seems to stop working, almost as if it is hung up. When I go to the ActiveSync window and tap Sync, it does absolutely nothing. Basically the only way i've found to get it to start working again is doing a soft reset.
Hopefully this will help you or other people out, because it took me FOREVER to figure this out. I am curious if anybody else is having problems with ActiveSync stopping responding with 6.1 also.
Click to expand...
Click to collapse
Lots of good info there. Thanks and I will let you know if this works the next time I flash.

kewlair said:
I'm sorry, I might not have been clear. ActiveSync on the device hangs up, not on my computer. I haven't had any issues with ActiveSync on my computer so I think this is a different issue.
Click to expand...
Click to collapse
juju-35's is a different issue. I agree. I am talking about over the air sync/push. I will try to edit the thread title to be more clear.

Camp said:
juju-35's is a different issue. I agree. I am talking about over the air sync/push. I will try to edit the thread title to be more clear.
Click to expand...
Click to collapse
Sorry for the confusion, I thought you were talking USB since you mentionned the PC to USB thing. Still annoying though . I will repost in the DCS thread!

Direct push works without issues over AT&T's network on 3.0 Sleuth. My job depends on it working too. I've used it over MEdiaNet and My ISP connections although you need to be able to use my ISP to get it to work correctly (without 7minute delays). You can tell if its using the correct connection by waiting for direct push to connect after a reset then tapping on the big 3G icon. It should say its connected using My ISP (this assumes you let the connection wizard discover your provider and set you up of course).
The only difference between your settings and mine is that my email system uses SSL.
Certs aren't an issue if your exchange implementation doesn't need SSL.
I would really like to see the exact activesync error code you are getting btw.

Sleuth255 said:
Direct push works without issues over AT&T's network on 3.0 Sleuth. My job depends on it working too. I've used it over MEdiaNet and My ISP connections although you need to be able to use my ISP to get it to work correctly (without 7minute delays). You can tell if its using the correct connection by waiting for direct push to connect after a reset then tapping on the big 3G icon. It should say its connected using My ISP (this assumes you let the connection wizard discover your provider and set you up of course).
The only difference between your settings and mine is that my email system uses SSL.
Certs aren't an issue if your exchange implementation doesn't need SSL.
I would really like to see the exact activesync error code you are getting btw.
Click to expand...
Click to collapse
It also happened to me on your newest 6.1 ROM Sleuth, thanks for chiming in here. I can only work on this issue during the weekend because come Monday I have to reflash to a working 6.0 ROM. I just reflashed with Dutty's newest 6.1 ROM and here are my updates (updated in first post also):
The ActiveSync error code that I originally got with all of the 6.1 ROMs is:
Result: Synchronization could not be completed. Try again later.
Support Code: 0x80830003
After trying kewlair's suggestion:
"The first issue I had was the initial setup. I set up my account properly, but ActiveSync would report that it cannot sync at this time. I knew that I had to uncheck the Use Proxy for this Connection option to solve this issue, but I couldn't find where to get to that setting for the MEdia Net connection that was being used. I finally found it in Settings -> Connections -> Advanced Tab, then tap the Select Networks button and where it says "Programs that automatically connect..." select MEdia Net instead of My ISP and then you can tap the Edit... button and remove the proxy server selection."
I get this ActiveSync error code. I also tried changing "Programs that automatically connect..." to My ISP with the same result:
ActiveSync tries to connect using either MEdia Net or My ISP and then says:
"Cannot Connect
Dialed: Cannot connect for an unknown reason. To check your connection settings and change them if needed, tap Settings. If the problem continues, reset your mobile device according to your manufacturer's documentation and try again."
ActiveSync Reports: "Waiting for network"
Thanks for all the help so far everyone.

Anyone else have any other ideas that I can try?

Have you tried not letting the network communication run and enter the att network connections manually. Just say No to configure your network config. I have had issues with the network communications auto setup.
1) Set up My Isp to use either wap.cingular or isp.cingular (depending on you data plan) and not setup the proxy.
2) Set up the work connection as medianet to use wap.cingular with the proxy setting
3) Set up MMS connection using the correct setting and using work connection (medianet) with proxy.
It really sounds like your issue is related to the network settings. If you look up your active sync error code on google all seem to point to the ATT proxy issues.
Good Luck

All
I use push Mail and have tries Sleuths and duttys 6.1 ROM without issues
SSL based Authentication
Cheers

Mario said:
All
I use push Mail and have tries Sleuths and duttys 6.1 ROM without issues
SSL based Authentication
Cheers
Click to expand...
Click to collapse
Same for me DCS 1.5 and now 1.7 with SSL no problem at all

Everyone does not need to post that yes it does work. Mine works as well as 99% of other people. This thread is just for the OP and any others whose does not work.
Yes, It does work for 99% to 99.9% of people!

eagle 1 said:
Everyone does not need to post that yes it does work. Mine works as well as 99% of other people. This thread is just for the OP and any others whose does not work.
Yes, It does work for 99% to 99.9% of people!
Click to expand...
Click to collapse
Thx but in that case error code would help. Because not working could come from many factor.
More strange is not working config when "upgrading" from WM6 to WM6.1 with STRICTsame config...
So if people could put more details it will help

The error code indicates that your exchange server is set to use client certs btw. Here's the exact recommendation to fix:
1. On the Exchange server, launch Internet Services Manager. Right click on the Microsoft-Server-ActiveSync virtual directory and choose Properties. Select the Directory Security tab. Click the Edit button in the Secure Communications section and select the option to “Ignore client certificates.”
Click to expand...
Click to collapse
This is a server-side fix though. If you're not the IT staff that did this, then you need to get them to give you the client cert again.
your upgrade to WM6.1 caused your client side cert to disappear. The cert store on WM6.1 contains different certs in the root store as well which could cause WM6.0 to have the cert your exchange server requires but not this beta version of WM6.1.
Exchange installations which require client side certs are very rare btw which is why everybody is saying "works great here". Generally, server certs are used instead (require SSL must be checked in this case)

eagle 1 said:
Have you tried not letting the network communication run and enter the att network connections manually. Just say No to configure your network config. I have had issues with the network communications auto setup.
1) Set up My Isp to use either wap.cingular or isp.cingular (depending on you data plan) and not setup the proxy.
2) Set up the work connection as medianet to use wap.cingular with the proxy setting
3) Set up MMS connection using the correct setting and using work connection (medianet) with proxy.
It really sounds like your issue is related to the network settings. If you look up your active sync error code on google all seem to point to the ATT proxy issues.
Good Luck
Click to expand...
Click to collapse
Solved. Thanks for everybody's help on this issue. eagle 1's answer above helped me find out what was wrong.
It was a really simple solution, but I have never had to mess with any of these settings on any of my previous WM devices. The solution was: The "Connection Setup" wizard did not set up my connection settings correctly. I had to set BOTH "Programs that automatically connect..." drop down options in the advanced connection settings to MEdia Net.
Thanks again to everyone that helped out.

surprising that you got a 0x80830003 error instead of the more common 0x8500200B (failed to contact server) message

Stopping win 6.1 using GPRS/EDGE connection

Hi, Ive just been checking my phonebill and noticed since upgrading to the 6.1WM my phone using the internet access (GPRS/EDGE). I cant physically see whats running in task manager, but it def is accessing the internet at certain stages. I have no email set up apart from windows live (Hotmail) and that is all signed out of? How to i stop this?

Have you already tried the following? The same helps to end GPRS/EDGE connection by using the Call End key (Red key) once you finished using the Internet. In fact, in many cases, the connection closes automatically after being idle for some time.
Go to: HKLM-->Comm-->ConnMgr-->Planner-->Settings-->SuspendResume
and delete ~GPRS! value.

maybe it is rss hub ? it can be configured to update rss each time it detects a connection.

In Dr. Gonzo's rom there is a util in the System folder called NoData. I use this to disable my gprs connection because I never use it and its pay per use. Its very simple to enable when you want to use data.

ok, ill take a look? What does HKLM mean?

It means you need to edit the registry on your phone, HKLM means "HKey Local Machine". I have just done this as it was leaving the data connection active on the standard WM6 HTC ROM, and it worked.
Thanks!

Thanks for the help.

Cannot connect to 802.1x PEAP MSCHAPv2 network

I cannot connect my AT&T Fuze to my work wireless network. This network requires the following settings:
Network Authentication: Open
Data Encryption: WEP (key is automatically provided)
Authentication: 802.1x Protected EAP (PEAP)
Inner Authentication: Secured password (EAP-MSCHAP v2)
Problem #1 - When I add the wireless network to the Wi-Fi settings, I select EAP type as "PEAP." I try to press the <Properties> button to set the inner authentication to MSCHAPv2, but receive an error message "Cannot log on to the network. This network requires a personal certificate to positively identify you." However this network does not require personal certificates.
Problem #2 - So I ignore that and press <Finish>. I am prompted for my credentials (username/password/domain). I enter them and press <OK>. No good. I am then repeatedly prompted for my credentials. [UPDATE: I just tried it for the 53rd time and just this once I was able to magically connect.]
I have read through many posts of similar complaints. I disabled server certification validatin by adding the ValidateServerCert value to the HKLM\Comm\EAP\Extension\25 key even though I have successfully installed the appropriate root certificate on the device. I also added the ValidateServerCert value to the \26 key just in case. I also set the wireless power mode to Best Performance.
What makes this particularly annoying is that I configured a coworkers iPhone to connect to the network. It was a giant pain because I had to install some sort of enterprise configuration software on a server and email her a mobile configuration profile from this application. Well the joke is on me because my WM6.1 phone cannot even connect.
Advice on what to do next? Thanks for your assistance.

I have the exact same problem... anybody found some sort of solution?
In case you still have the problem:
http://www.securew2.org/
Their program helped me overcome my issues with peap. Hope it works for you too
(taken from http://forum.xda-developers.com/showthread.php?t=284534&page=2 )

Thanks! Just how i tried - and too workng!

In case you still have the problem:
http://www.securew2.org/
Their program helped me overcome my issues with peap. Hope it works for you too
Click to expand...
Click to collapse
I am the OP. I was looking at SecureW2 as a last resort, as I am generally opposed to installing 3rd party applications to perform what should be core OS functions. Too many potential issues down the road. Fortunately I overcame my problem #2 stated above. On a separate post, somebody captured network traffic and determined that credential request/response was getting out of sync b/c the access point was not allowing enough time to respond. So after entering credentials and checking the "Save" box, I just banged away on the <OK> button as fast as possible. Eventually I connected. At this point the credentials are cached so I immediately connect from then on. I have tried this on two different HTC Fuze devices to my company's 802.1x PEAP MSCHAPv2 wireless network and it works great.
I also verified that since I installed the proper root certificate on my Fuze, I do not need to disable certificate validation by changing the ValidateServerCert registry value.
So the Windows Mobile 6.1 networking has two problems that will hopefully be fixed in a future update to make this easier for everyone.

So all you do is hit the OK button as fast as possible?

just making short login ans password

So all you do is hit the OK button as fast as possible?
Click to expand...
Click to collapse
Yes if you are experiencing problem #2 in the original post, repeated login prompts even though you know the credentials are correct.
just making short login ans password
Click to expand...
Click to collapse
The length of the username and password do not matter. And most credentials used with corporate networks are subject to complexity rules so cannot be arbitrarily short.

I found another solution, well the It guys from my Uni did.
Apparently you just have to increase the Wifi power setting to max. Otherweise the phone cannot process the peap crypto processes as it is limited by power saving mode.
http://social.microsoft.com/Forums/en-US/windowsmobile/thread/101f89b3-87fc-4cef-ac92-ece1aca9c12f/

i have the same problem. i dont understand how you overcame it

as0r: Changing the wifi power setting did not resolve problem #2 described in my original post, repeated login prompts.
jvar11889: How far did you make it, are you experiencing at problem #2 described in my original post, repeated login prompts? Is your required wifi configuration the same (802.1x PEAP MSCHAPv2)? I have succeeded on two different Fuzes, multiple times.

as0r said:
I have the exact same problem... anybody found some sort of solution?
In case you still have the problem:
http://www.securew2.org/
Their program helped me overcome my issues with peap. Hope it works for you too
(taken from http://forum.xda-developers.com/showthread.php?t=284534&page=2 )
Click to expand...
Click to collapse
I used this solution and worked for me!
Tried all the other tips mentioned, like for example the "power trick", without any luck!
However i have just flashed my TP from stock norwegian ROM to ROMeOS, dont know if this had any influence, but sercurew2 did the trick!
Its not really a 3rd party software, more like and integration into windows mobile!
Follow the instalations and setup guide from the site!
And Thanks for posting this, i have tried to get it working for more than 2 weeks now

Its not really a 3rd party software, more like and integration into windows mobile!
Click to expand...
Click to collapse
I disagree because the release notes clearly list the DLL's installed on your device. There is nothing inherently wrong with 3rd party software; I just like to reduce complexity by only installing additional software when I can't get what I want using the buillt-in features. If this was the only way I could connect to my 802.1x network, I would certainly install it.
I'm glad you are up and running. I have a hard time believing Microsoft is not aware of these problems. If they are serious about WM competing with iPhone and Android, Microsoft needs to jump on top of problems like this.

rlsmith999 said:
I disagree because the release notes clearly list the DLL's installed on your device. There is nothing inherently wrong with 3rd party software; I just like to reduce complexity by only installing additional software when I can't get what I want using the buillt-in features. If this was the only way I could connect to my 802.1x network, I would certainly install it.
I'm glad you are up and running. I have a hard time believing Microsoft is not aware of these problems. If they are serious about WM competing with iPhone and Android, Microsoft needs to jump on top of problems like this.
Click to expand...
Click to collapse
I agree with you! MS should do something about this! However, i talked to the EU HTC Support team, and they said a new ROM / Fimrware is due to be released end of February! Maybe there will be some kind of fix to this problem? Have heard that the HTC TP have some kind of problems installing certificates or something like that (havent read this myself, just heared it from someone working in a Cell Phone shop).
Hope you'll post here if you find a better solution!
Good luck!

zemlol said:
I used this solution and worked for me!
Tried all the other tips mentioned, like for example the "power trick", without any luck!
However i have just flashed my TP from stock norwegian ROM to ROMeOS, dont know if this had any influence, but sercurew2 did the trick!
Its not really a 3rd party software, more like and integration into windows mobile!
Follow the instalations and setup guide from the site!
And Thanks for posting this, i have tried to get it working for more than 2 weeks now
Click to expand...
Click to collapse
I am glad it helped you, but it stopped working for me a couple of days ago. Would you mind posting your config?
Cheers

Try and go into the securew2 settings tab !
And check for "prompt for username and password" ?
It switches on and off sometimes!
What config info you want?

hi boys...
i have the same problem... I cant connect to wifi of my university because his used a protocol that not compatible of andoid...
this is the guide of my University for linux sistem...
Sicurezza wireless: WPA e WPA2 Enterprise
Autenticazione: EAP Protetto (PEAP)
Identita anonima : anonymous
Certificato della CA: (Nessuno)
Versione PEAP: Versione 0
Autenticazione interna: MSCHAPv2
utente : il proprio indirizzo di mail studenti (esempio [email protected])
Password: ( la password del servizio wifi inserita in fase di attivazione)
now the problem is that my liquid ask me only password, and only for this not possible to connect.
anyway help me...

Same here
i have the same issue as well. i have tried all kinds of solutions. adding the reg key, securw2, advanced config tool and many more but nothing has worked. i even flashed a new 6.5 rom and that didnt work either. my fellow techs have i-phones and they find this pretty funny so i would love to get it to work. I like htc and dont really want to go to iphone so hopefully someone out there has the solution that works.

treo 750 and the "built-in" ms voip client

hello all,
1. I have been unsuccessfully trying to install the ms voip client that's been deliberately cut out of all roms for 750's
I followed all the possible instruction sets similar to, say, here:
http://forum.xda-developers.com/showthread.php?t=401608&highlight=voip
Everything seems to install ok and you can even configure the thing to go through 3g, but it just doesn't want to actually start working.
Problem number one - no internet tab in phone settings
Problem number two - the today plugin is always in the "off" state.
My thoughts on this:
These problems might be coming out of the fact that 750's don't have wi-fi which seems to be the default behaviour for the voip client.
Also, according to here:
http://msdn.microsoft.com/en-us/library/aa923501.aspx
hklm\comm\rtc\ doesn't look like it has enough settings
2. On top of it all i'd like to bring g.729 codec support to the attention.
All i've been able to dig up is that you have to put the .acm file in the right place -> add some registry settings:
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\CODEC_G729]
"Prefix"="ACM"
"Dll"="g729.acm"
"Order"=dword:0
"Flags"=dword:2
-> and then configure the use somewhere in \\hklm\comm\rtc\
Has anyone successfully installed and used it?
Let's bring all these things together so it all starts making sense.
Thank you for your time.

I have the same problem.
No matter what I install, the "internet" option never becomes available in the phone settings.
I believe this may have to do with "PLMOCPL.cpl" being used as the phone settings CPL instead of "cplmain.cpl" on the Palm.
I have changed a setting under "HKLM>System>State>VoIP>Phone". I changed "Network Preferences" from 0 to 1, which i think is what the control panel does anyway.
Now instead of "Internet Calling: Off", I get "Pennytel: No Service".
Anyonw else come up with anything? Any way to edit the cpl to include the internet settings?