I've asked before but haven't come across anything that helps. My Fuze, with hardspl and the olipro unlocker and a 6.5 rom (TAEL) now doesn't show up on USB. I get the USB Device Not Recognized error with a listing of Unknown Device in the detail window. Cycling the high speed USB resets the connection but does not resolve the error. My old Tilt works fine on the desktop and on the laptop. The Fuze does not work on either. I was unable to replace the serialUSBfn.dll file even with Total Commander as the file seems to be in use. I hard reset the device and finally reflashed the phone by SD in an attempt to replace the file. This wiped my associations in ActiveSync so I can't sync or for that matter set up the phone for the first time over BT.
I also tried to get it to be available from the bootloader with no success.
I've checked the USB contacts on the phone, reset the power on the device and the PC, etc. I've found many tips but none that have helped.
So, my questions are, in no particular order are:
(1) is there a code element that is passed to the PC upon USB connection that I need to replace, such as a bootloader? Can this be done by SD flashing?
(2) If this is hardware problem and USB is dead, can my contacts be loaded in a single action by a data file import by email or SD?
(3) Can BT be used for an initial sync through any unusual process?
(4) Should I re-run hardSPL or the Olipro unlocker to reset anything?
(5) Does anyone have any other suggestions?
(6) Is this a dead phone that need to go somewhere for service?
Bob Simons said:
I've asked before but haven't come across anything that helps. My Fuze, with hardspl and the olipro unlocker and a 6.5 rom (TAEL) now doesn't show up on USB. I get the USB Device Not Recognized error with a listing of Unknown Device in the detail window. Cycling the high speed USB resets the connection but does not resolve the error. My old Tilt works fine on the desktop and on the laptop. The Fuze does not work on either. I was unable to replace the serialUSBfn.dll file even with Total Commander as the file seems to be in use. I hard reset the device and finally reflashed the phone by SD in an attempt to replace the file. This wiped my associations in ActiveSync so I can't sync or for that matter set up the phone for the first time over BT.
I also tried to get it to be available from the bootloader with no success.
I've checked the USB contacts on the phone, reset the power on the device and the PC, etc. I've found many tips but none that have helped.
So, my questions are, in no particular order are:
(1) is there a code element that is passed to the PC upon USB connection that I need to replace, such as a bootloader? Can this be done by SD flashing?
(2) If this is hardware problem and USB is dead, can my contacts be loaded in a single action by a data file import by email or SD?
(3) Can BT be used for an initial sync through any unusual process?
(4) Should I re-run hardSPL or the Olipro unlocker to reset anything?
(5) Does anyone have any other suggestions?
(6) Is this a dead phone that need to go somewhere for service?
Click to expand...
Click to collapse
When you attempt bootloader mode does USB show up on the tricolour screen?
bootloader now shows serial, not usb
since I attempted to set it up on BT to try to sync it that way, it now says serial, and in fact the mobile device shows up on My Compuer and I can see all folders and so on. If it matters, the SIM is out in the Tilt at present. Prior to setting up BT pairing it had been showing USB.
with usb cable attached, bootloader mode says nothing. pulling the cable in bootloader mode, it then shows serial.
These problems started after I set Activesync to exchange mode: does this change a hardware setting that is not reset by flashing or pulling the battery?
Not sure if it will help.
If you can I would rerun Hard SPL and Olipro. That is where I would go. I am no expert but hey, no one else is responding.
Bob Simons said:
since I attempted to set it up on BT to try to sync it that way, it now says serial, and in fact the mobile device shows up on My Compuer and I can see all folders and so on. If it matters, the SIM is out in the Tilt at present. Prior to setting up BT pairing it had been showing USB.
with usb cable attached, bootloader mode says nothing. pulling the cable in bootloader mode, it then shows serial.
These problems started after I set Activesync to exchange mode: does this change a hardware setting that is not reset by flashing or pulling the battery?
Click to expand...
Click to collapse
Try another USB cable.
Have you ever flashed w/ microSD? See how 2 do it in the first threads in this forum...
Try this procedures:
1st - HSPL;
2nd - Stock ROM;
3rd - Cooked ROM...
Hard Reset after each step
See if it worked
try to go to settings>connections> USB to PC; then uncheck (Enable advanced network functionalty).
then try again.
I've tried multiple cables and have changed the settings
as I say in the post.
Related
Hi all I know there's been many a post about being stuck in the bootloader and I even went to the wiki to see what to do.
Firstly, when following the wiki (http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader) on the mtty_utility there is no option for USB only comm 1, 2, or 3 (am i being stupid?).
Secondly, I had a guess and tried all the comm's and eventually comm three seemed to be the only one working, but when I type in the commands it does not do anything.
Any help would be greatly appriciated as I would hate to see my uni go its been so good to me.
Thanks in advance
Jo
Please help
The USB option is at the very bottom of the list. Unless your PC isn't registering the ports, you should be able to get MTTY to work for that part at least.
Thanks for the reply but there wasn't a USB option, I've tried everything, I think it may be to do with vista continuously wanting to run mobsync.exe whenever I plug the uni in but there's no way to stop it.
I've tried ending it as a process but mtty still doesn't have the option of USB.
If you have any ideas please post them, am I right in beleiving that you cannot charge in bootloader mode? Or is that just off the USB?
Thanks
Jo
P.S. The laptop I'm using can read other things through the USB ports, and I have tried every port just to double check that they are not all on the same line (ie an internal hub).
I think it may have something to do with Vista... I'm not sure as I don't have a Universal...
If you have access to XP it may be faster and easier...
I think you may be right
I shall wait untill my housemate gets back in, if it doesn't work in safemode!
Cheers for your help anyway!
I shall keep all informed just in case anyone else ever has this problem
Got it working!
Right finally got it working! It took some time but I managed to revive it!
1) Connect your device in bootloader (Hold light button, power button, and reset),
2) Open Windows Mobile Device Center and in connection settings uncheck Allou USB Connections,
3) Goto contol panel-administrative tools-services and start windows mobile device connectivity and windows mobile device 2003 connectivity,
4) goto device manager and find your device and update the driver to the one that can be found here: http://forum.xda-developers.com/showthread.php?t=313001&highlight=vista (it is the one in the modem folder, do not follow their instructions, it will not work in this case),
5) Open task manager and kill wmdc.exe, or anything with wm infront of it, also kill mobsync.exe
6) Goto: http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader and follow the instructions (you should be able to see USB as an option now).
In mtty it took a couple of commands before it actually executed then once finished it looked as though it were completely dead, but connect the uni to the comp again in bootlaoder mode and all should be well!
With Reference to:
http://forum.xda-developers.com/showthread.php?t=291723
PS could someone put this in the wiki under the title "If mtty does not have the USB option in vista" I'm being a dunce and don't really know how to do it
I am running WM 6.1 (Michyprima Full) and I wanted to flash to another ROM, however for some reason my phone will no longer connect to activesync on the desktop (tried two pcs). It can sync just fine via exchange.
Nothing has changed on the mobile device or the desktop; ActiveSync on the mobile device is set to allow connection via USB and activesync on the desktops is set to use USB to sync.
I know the underlying connection is ok because the device will start charging from the USB cable when it is hooked up.
What can I do to fix this situation so I can flash to a new ROM? I do not need to save anything on the device... I have tried soft-resetting.
EDIT: Also when I list USB connected devices on the desktop PC, I see one called "Windows Mobile-based Device"
did you use a ram cleaner
i used a ram cleaner and my device dosent get recognised by pc.let me know if you find a solution.
padanfain said:
I am running WM 6.1 (Michyprima Full) and I wanted to flash to another ROM, however for some reason my phone will no longer connect to activesync on the desktop (tried two pcs). It can sync just fine via exchange.
Nothing has changed on the mobile device or the desktop; ActiveSync on the mobile device is set to allow connection via USB and activesync on the desktops is set to use USB to sync.
Click to expand...
Click to collapse
Have you tied going to Start/Settings/System (or Connections) and running USB to PC? Try unchecking 'Enable enhanced network' then OK back to the start screen and try reconnecting.
If that doesn't work, try a hard reset with the current ROM, and see if that fixes it. If so, you can then flash the new ROM.
If it still doesn't work, I think you can flash using a memory card or the Flash Drive without needing to access the PC.
padanfain said:
I am running WM 6.1 (Michyprima Full) and I wanted to flash to another ROM, however for some reason my phone will no longer connect to activesync on the desktop (tried two pcs). It can sync just fine via exchange.
Nothing has changed on the mobile device or the desktop; ActiveSync on the mobile device is set to allow connection via USB and activesync on the desktops is set to use USB to sync.
I know the underlying connection is ok because the device will start charging from the USB cable when it is hooked up.
What can I do to fix this situation so I can flash to a new ROM? I do not need to save anything on the device... I have tried soft-resetting.
EDIT: Also when I list USB connected devices on the desktop PC, I see one called "Windows Mobile-based Device"
Click to expand...
Click to collapse
Have you tried completely uninstalling ActiveSync from your computer, reboot, download and re-install ActiveSync. Its worked for me - sometimes the USB drivers become corrupt.
When I try and hit ok to commit the change of unchecking the advanced network functionality (it was checked before), the device just sits there with the spinning thinking wheel. Doing a soft reset and going back into the usb to pc shows the box still checked.
I will try a hard reset.
padanfain said:
When I try and hit ok to commit the change of unchecking the advanced network functionality (it was checked before), the device just sits there with the spinning thinking wheel. Doing a soft reset and going back into the usb to pc shows the box still checked.
I will try a hard reset.
Click to expand...
Click to collapse
I think thats the only answer at present- the inability to change the A/S settings on the device suggest something's got corrupted somewhere
I was able to get it to sync after a hard reset.
However, when I attempted to load Michy's light ROM the device rebooted and sat at "Loading..." with a white screen. The wrapper then said error connection failed.
If I soft reset the device it comes back to the loading... screen; if I hard reset the device, it comes back to the loading screen after the hard reset. How can I fix this?
blast. left the stupid sd card in while i did the first flashing.
Removed SD card, re-hard resetted, then re-ran the ROM updater.
Sometimes its OK, sometimes it isn't- just one of those little mysteries I guess!
Glad its OK now. Michy's Lite ROM is excellent
Solution for deleted active sync notification called replog
YES...you guys definitely ERASED your Active sync NOTIFICATION file called replog. As someone suggested...he ran his CLEANER...then the problem begun.
It is true that Hard Reseting the device will get you back that file, but there is an easy way to do it...I can't find the original article but this file I will post will RE-CREATE that deleted replog notification file that is needed by active sync to work.
So next time you try and clean-up...just make sure you won't delete any file named replog
To use this FIX, just place it on your SD Card and run the file. If you want you can create an icon at Windows>Start Menu>Programs>to whatever folder... that will work too for easy access.
Just a word of caution...DON'T RUN THE FILE MORE THAN ONCE...why? Because it will re-create the file again. Although it won't hurt in any way except eat up internal memory, but you don't want any duplicated file... right?
My pc says my connection settings in my phone need to be changed. I don't remember changing anything and I don't know what to change them to.
My phone tells (after a failed connectoin) me there is a connection error and opens MEdia net settings. I don't know what that would have to do with anything. I know I haven't changed them. There is no need. When this problem came up I tried changing some things, they didn't work, so I put them back. This is the same PC I always connect the phone to. I don't know what has changed other than i was gone for a month for work.
I need help please.
the last flash was Energy ROM 20090801 standard
tweakedlogic said:
My pc says my connection settings in my phone need to be changed. I don't remember changing anything and I don't know what to change them to.
My phone tells (after a failed connectoin) me there is a connection error and opens MEdia net settings. I don't know what that would have to do with anything. I know I haven't changed them. There is no need. When this problem came up I tried changing some things, they didn't work, so I put them back. This is the same PC I always connect the phone to. I don't know what has changed other than i was gone for a month for work.
I need help please.
the last flash was Energy ROM 20090801 standard
Click to expand...
Click to collapse
Have you played with your USB to PC settings, untick\tick "Enable Faster Data"
If not, delete your sync relationship and establish a new one.
Yeah, I did both of those already. the only thing I can think to do is push the little button call "Wipe Device". then flash a new rom. I'm worried I will not be able to flash after that though.
I'm scared
Something is messed up... Sounds like a hard reset or a reflash is in order.....
Do you get the connection option screen when you plug it in to USB that says connect as:Active Sync, Modem or hard drive?
Usb Problem
From what i have seen, it can be the usb wire
darkreborn said:
From what i have seen, it can be the usb wire
Click to expand...
Click to collapse
Could be true. My usb wire at my studio is bad and I always have to curve it to make it work.
I might be mistaken, but I think I got a similar message a while back. I changed the setting in File->Connection Settings-> This computer is connected to: The Internet
And that did the trick for me...
I have an HTC HD with stock rom
I recently had to change my sd card for a new one.
I hard reseted to reinstall all my programs.
Bluetooth sync is ok but NO MORE SYNC BY USB NOW !
So I cannot install net CF 3.5 or sync music or GPS maps (files take too much time 'cause too big) ...
I have hard reseted my device, uninstalled and reinstalled WM device center latest version, unchecked "activate advanced network" in "usb to pc settings", deconnected my firewall and anti virus; tried active tweak freeware; changed cable ... NOTHING WORKS. No connection, no sound, no error message...
Please help !!!
If put your HD into bootloader, and you connect it to the pc, does the text 'serial' change into 'USB'?
If so, there's nothing wrong with the drivers so we need to look further.
If not, your drivers do not work.
Let me know if the text changed or not, then I'll see if I've got some solutions for you.
Hi Condor.
I don't see any change when I do as you told me. Serial doesn't change into USB.
Thanks for your help.
Finally had to bring my phone for repair. The motherboard has been changed. Now everything's OK.
I have bought a i9305t with a broken screen through a private sale. After connecting it to a working screen, I discover a few strange problems:
1. I can't get the phone into download mode or recovery mode by the normal key combinations. So I can't do any factory reset.
2. The phone can power up, but it stops at a log in screen requesting a pin input, although when I asked the previous owner about it, he said he never had set up any locking pins.
3. In that pin-entering mode, when I connect the phone to my PC (windows 7), the PC recognise the connection and displayed a i9305t in windows explorer, but the explorer can't show any content details of the phone. When I run the Odin with the phone in this mode, the COM window changes colour, but any attempts to flash any tar file stops at 'SetupConnection..' step, and after a while, it comes back with a 'FAIL!'.
4. I have a usb jig, and with that, I can force the phone in download mode. However, when the phone is in that mode, Odin doesn't recognise the connection at all when I plug the phone in, so I can't do any flashing in that mode.
So I am totally stuck! I thought about going through ALL the pin combinations to try to unlock the phone (assuming the pin is a 4 digit number). After spending one and a half hours to go from '0000' to '0500', I thought this is rediculous! There must be a better way! So I hope some guru out there would be able to help me, as I have exhausted all my tricks (which is not that many!).
If anyone can show me a way to get around my problems, it would be most appreciated!!!
Missing IMEI
tdrinker said:
I have bought a i9305t with a broken screen through a private sale. After connecting it to a working screen, I discover a few strange problems:
1. I can't get the phone into download mode or recovery mode by the normal key combinations. So I can't do any factory reset.
2. The phone can power up, but it stops at a log in screen requesting a pin input, although when I asked the previous owner about it, he said he never had set up any locking pins.
3. In that pin-entering mode, when I connect the phone to my PC (windows 7), the PC recognise the connection and displayed a i9305t in windows explorer, but the explorer can't show any content details of the phone. When I run the Odin with the phone in this mode, the COM window changes colour, but any attempts to flash any tar file stops at 'SetupConnection..' step, and after a while, it comes back with a 'FAIL!'.
4. I have a usb jig, and with that, I can force the phone in download mode. However, when the phone is in that mode, Odin doesn't recognise the connection at all when I plug the phone in, so I can't do any flashing in that mode.
So I am totally stuck! I thought about going through ALL the pin combinations to try to unlock the phone (assuming the pin is a 4 digit number). After spending one and a half hours to go from '0000' to '0500', I thought this is rediculous! There must be a better way! So I hope some guru out there would be able to help me, as I have exhausted all my tricks (which is not that many!).
If anyone can show me a way to get around my problems, it would be most appreciated!!!
Click to expand...
Click to collapse
----------
Problems solved! Well, most of them anyway. I found I got the wrong usb driver on my PC. After updating with the correct Samsung usb driver, I could connect to Odin, thus I could flash a CWM recovery rom, so I could do a factory reset.
However, after the phone has booted up, for some reason, I found the IMEI is missing, so I couldn't connect to any network when I insert my sim card. I don't know how that happened. Can anyone help me with that? Many thanks.