Slingplayer not working with Verizon TP2? - Touch Pro2 CDMA

Anybody get slingplayer to work on their Verizon TP2 over the 3G connection? I keep getting the error message "Unable to connect to Slingbox". I have tried locating the slingbox using both the "Slingbox Finder ID" and the "IP Address".
If I try it from the same wifi network as the slingbox, it is able to find the slingbox. I remember having a similar issue on AT&T's network and having to change the connection settings from wap.cingular.com to isp.cingular.com

I was able to install slingplayer and run without any problems. I think there is a way to connect by entering your username and password, you might try that.

I had that issue with my Saga. As it turned out, for some reason my router closed some ports and the box wouldn't go out over the internet. It worked fine on the local network but didn't work if it had to go through the router.
Might want to check that.

Verizon TP 2 working fine with slingplayer here. I used to get the same message every few days. I found that if I disconnected the power from my slingbox and then plugged it back in, I was able to connect again. The problem is that you have to be home in order to do this. I ended up plugging my slingbox into a timer that shuts off for 1 minute and back on at midnight and noon each day. After doing that, my connection problem went away. Hope this helps you... it was a lifesaver for me. I was pulling my hair out in frustration when I couldn't connect.

Can you connect with a computer to watch your slingbox from outside of your network? Its probably a port setting on your router. Try opening up the ports in the attached screen shot.

Just a warning, last I checked, Slingbox was against VZW's t&c's. (When I worked there in 2008).
Be careful.

Related

Modem/dial-up not working using ATT Fuze and Energy 2.0 ROM

first off - i tried searching but could not find any solid info, from start to finish, how to make tethering work
i've never had to tether till now.. tried enabling Internet Sharing and connecting it both via USB and Bluetooth - no success.. i'm using Media Net $15 a month data plan, if that makes a difference (wap Vs gprs in user name but i did try both)...
is anyone using their phone as a modem? what settings do you have? please point the noob in the direction of a step-by-step guide if one is available (i did try to search but nothing than enabling Network connection via registry edit - not relevant)..
thanks a bunch to anyone who could help!
I'm online using the "internet sharing" connection now (in Florida cleaning up after a flood) (Yes, I need to get back to work . . . .).
I also have a Fuze and am using EnergyROM 2.0. Haven't changed any settings since installing the new ROM. Works like a charm for me.
Make sure the proxy box under the MediaNet settings is NOT checked.
vovan75 said:
first off - i tried searching but could not find any solid info, from start to finish, how to make tethering work
i've never had to tether till now.. tried enabling Internet Sharing and connecting it both via USB and Bluetooth - no success.. i'm using Media Net $15 a month data plan, if that makes a difference (wap Vs gprs in user name but i did try both)...
is anyone using their phone as a modem? what settings do you have? please point the noob in the direction of a step-by-step guide if one is available (i did try to search but nothing than enabling Network connection via registry edit - not relevant)..
thanks a bunch to anyone who could help!
Click to expand...
Click to collapse
Open up taskmanager and make sure that activesync is not running on the phone. this will not allow internet sharing to work. what does the phone say when you open internet sharing and click connect?
download a registry editor (i use total commander, and it works just fine).
open it up, go to \plugins\registry\HKLM\Comm\InternetSharing\Settings\ForceCellConnection and simply delete the contents of the value so that it's empty. Go ahead and do a soft reset and open up the internet sharing app. From there, select the Media Net connection and hit connect. Voila, good to go!
Enjoy!
ps I've gotten 2+ Mbps speeds via tethering
Dane Austin said:
Open up taskmanager and make sure that activesync is not running on the phone. this will not allow internet sharing to work. what does the phone say when you open internet sharing and click connect?
Click to expand...
Click to collapse
I keep activesync enabled so that i'm able to receive corporate email when on the road.
I was able to tether via USB (was doing nothing different from last night when i was unable to internet share via USB, however I noticed when shutting down that BT stack crashed); internet sharing app came up automatically once I selected internet sharing right after hooking up the cable to my laptop, and MediaNet was there by default (I guess it's all cooked into the ROM; did not have to delete any registry keys; kudos to NRGZ)... was able to get close to 1Mb/s download speed (upload is really slow however, less than 50Kb/s) - not too bad overall
Still have problem connecting via Bluetooth
maybe i'm having problem pairing laptop and Fuze? is there a pre-defined code/pass key that i'm supposed to use for the Fuze?
i was just using my security/lock code.. when laptop starts dialing (is dial up number *99# correct?), i get the following error box:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99#...
Error 678: The remote computer did not respond. For further assistance, click More Info or search Help and Support Center for this error number.
-------------------------------------------------
Anybody had this issue? or can share their connection settings for Bluetooth?
thanks everyone who responded!
vovan75 said:
I keep activesync enabled so that i'm able to receive corporate email when on the road.
I was able to tether via USB (was doing nothing different from last night when i was unable to internet share via USB, however I noticed when shutting down that BT stack crashed); internet sharing app came up automatically once I selected internet sharing right after hooking up the cable to my laptop, and MediaNet was there by default (I guess it's all cooked into the ROM; did not have to delete any registry keys; kudos to NRGZ)... was able to get close to 1Mb/s download speed (upload is really slow however, less than 50Kb/s) - not too bad overall
Still have problem connecting via Bluetooth
maybe i'm having problem pairing laptop and Fuze? is there a pre-defined code/pass key that i'm supposed to use for the Fuze?
i was just using my security/lock code.. when laptop starts dialing (is dial up number *99# correct?), i get the following error box:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99#...
Error 678: The remote computer did not respond. For further assistance, click More Info or search Help and Support Center for this error number.
-------------------------------------------------
Anybody had this issue? or can share their connection settings for Bluetooth?
thanks everyone who responded!
Click to expand...
Click to collapse
now, i just tried leaving User Name and Password fields blank on the Bluetooth connection wizard, and using dial-up number *99***1#, like they suggest here: Answer Center - Create a Windows XP Dial-Up Networking Connection for a Bluetooth Device , and got a new error:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99***1#...
Error 777: The connection attempt failed because the modem (or other connecting device) on the remote computer is out of order.
-------------------------------------------------
this is just getting funnier but kind of frustrating...
nhshah7 said:
download a registry editor (i use total commander, and it works just fine).
open it up, go to \plugins\registry\HKLM\Comm\InternetSharing\Settings\ForceCellConnection and simply delete the contents of the value so that it's empty. Go ahead and do a soft reset and open up the internet sharing app. From there, select the Media Net connection and hit connect. Voila, good to go!
Enjoy!
ps I've gotten 2+ Mbps speeds via tethering
Click to expand...
Click to collapse
tis fixed my tethering issue... thank you!
Damn AT&T trying to force people to pay more for tethering... shame!
smittyofdhs said:
tis fixed my tethering issue... thank you!
Damn AT&T trying to force people to pay more for tethering... shame!
Click to expand...
Click to collapse
smitty, do you tether via bluetooth or usb? i have no problem with usb now but still get the same "error 678: the remote computer did not respond..." i wonder if my BT driver is corrupt or i'm blacklisted by at&t
if anyone is able to connect using bluetooth and Internet Sharing app on Energy or any other similar ROM, can you share your dial-up settings with me?
after i start Internet Sharing app, with PC Connection = Bluetooth PAN and Network Connection = MEdia Net, and then right click my Bluetooth Modem in Dial-up Network Places on my laptop, the icon shows "connecting" for about 5 seconds (and the data icon H on the phone starts rotating) and then the error comes up on computer screen.. i can't believe no one else has had the same issue, i must be something with my laptop
vovan75 said:
smitty, do you tether via bluetooth or usb? i have no problem with usb now but still get the same "error 678: the remote computer did not respond..." i wonder if my BT driver is corrupt or i'm blacklisted by at&t
if anyone is able to connect using bluetooth and Internet Sharing app on Energy or any other similar ROM, can you share your dial-up settings with me?
after i start Internet Sharing app, with PC Connection = Bluetooth PAN and Network Connection = MEdia Net, and then right click my Bluetooth Modem in Dial-up Network Places on my laptop, the icon shows "connecting" for about 5 seconds (and the data icon H on the phone starts rotating) and then the error comes up on computer screen.. i can't believe no one else has had the same issue, i must be something with my laptop
Click to expand...
Click to collapse
I haven't been able to get my HP laptop to pair via bluetooth with my Fuze yet so I was doing USB. With regards to your issue, do you ahve one or two pull down menus in INternet Sharing app? If you have 1, then your registry needs to be hacked. AT&T used a registry key to force Internet Sharing app to only use the isp.cingluar access point (instead of wap.cingluar). If you pay the extra bucks for the full unlimited with tehtering then your account is setup to use isp.cingluar as well as wap.cingluar. If you just have the normal unlimited w/o tehtering option (which is not unlimited it caps at 5GB/month) then you only can use wap.cingluar. THis is how AT&T is going more easily find people using the cheaper plan with thethering and of course charge them up the butt for violation of the TOS (that they keep changing). Removing the registry key, fixes the issue.
smittyofdhs said:
I haven't been able to get my HP laptop to pair via bluetooth with my Fuze yet so I was doing USB. With regards to your issue, do you ahve one or two pull down menus in INternet Sharing app? If you have 1, then your registry needs to be hacked. AT&T used a registry key to force Internet Sharing app to only use the isp.cingluar access point (instead of wap.cingluar). If you pay the extra bucks for the full unlimited with tehtering then your account is setup to use isp.cingluar as well as wap.cingluar. If you just have the normal unlimited w/o tehtering option (which is not unlimited it caps at 5GB/month) then you only can use wap.cingluar. THis is how AT&T is going more easily find people using the cheaper plan with thethering and of course charge them up the butt for violation of the TOS (that they keep changing). Removing the registry key, fixes the issue.
Click to expand...
Click to collapse
sounds like we are in the same boat here - i can tether my HP laptop with Fuze via USB no problem now using Internet Sharing app, but no luck with Bluetooth whatsoever... i don't think there is an issue with the registry ever since i switched to Energy 2.0 ROM which must have the settings customized (so yes, I do have 2 pull down menus, and I have Media Net selected in the second one). So, I tried to use both wap.cingular and isp.cingular APN's (both [email protected] and [email protected] for User Name, CINGULAR1 for password; then I tried leaving User Name and Password fields blank...) with no success... nothing works, damn it!!!
looks like it gets paired up briefly, then starts dialing and gets the error in a couple of seconds.. the problem must be with the bluetooth dial-up settings for AT&T, because: 1) i have no problem tethering via USB; 2) Fuze is being paired up with my laptop and trying to use HSPDA data connection (as indicated by rotating H on the phone for a few seconds while my laptop tries to dial up).
by the way, have you tried dialing *99# or *99***1# (i tried both numbers as well as *99***3# for Samsung phones) from your Fuze, did you get any modem dial tone??
thanks!
I was able to connect to internet through bluetooth by using the following settings.
After pairing the bluetooth on both Fuze and laptop:
On my Fuze: open 'Internet Sharing' then select Bluetooth PAN and choose the appropriate network connection (in my case TZones) then tap 'Connect'
On the laptop: open bluetooth neighborhood then 'discover service' or 'explore' on the Fuze device. You should see 'Network Access Point on [Fuze]' and then double click on it.
Done.
ICS on AT&T HTC Fuze Cut Off (NRG Rom Series 2.0)
AUTiger83 said:
I'm online using the "internet sharing" connection now (in Florida cleaning up after a flood) (Yes, I need to get back to work . . . .).
I also have a Fuze and am using EnergyROM 2.0. Haven't changed any settings since installing the new ROM. Works like a charm for me.
Make sure the proxy box under the MediaNet settings is NOT checked.
Click to expand...
Click to collapse
I've been using ICS with no problems with a ThinkPad T43 for a few weeks at work to circumvent the proxies and reach out to my home machine via RDP. The RDP app for the Fuze just doesn't cut it with its whopping 640x480 screen. Turns out that AT&T in NY/NJ is somehow monitoring the connections. I was watching a bunch of videos to pass some downtime, and I guess I triggered some kind of alert on their end. ICS will connect to MediaNET with no problems (settings read wap.cingular), ICS status shows connected (I am connecting over USB) and my ThinkPad network connection shows a private IP address handed to it by the phone (192.168.0.x range). However when I am trying to connect to something, I'll get timeout errors. Running a simple ping comes back with no DNS capabilities as I can't even ping google.com... Has this happened to anyone on the forum? Can anyone offer some advice? I am thinking of just calling AT&T and playing dumb, saying that I was watching videos, as well as moving lots of music from my home computer via FTP ... Any advice appreciated. I pay for the $40/month PDA plan... I don't see the point of paying for tethering when you're already paying for data. Yes, before people start flaming me, I was stupid by using the connection to watch a bunch of videos, but you're able to watch youtube on your phone anyway....
--UPDATED 7-31-09 3:03PM --
So I downloaded ICS Control v0.21, which by the way is an awesome program. I went through the config, was able to connect my laptop to my HTC Fuze via WiFi. That was easy. As palringo (win xp version) was connecting in the background, I was able to do a test google search and get back results. Ran a continuous ping on google (ping google.com -t). Turns out that after about 25 ping replies or so, just about the time it took me to do a few web searches, the requests start timing out. Directing the ping at another website shows that the ping request couldn't find the host... basically the same problem I had tethering over USB. It's as if the AT&T network is determining that the request is coming from a PC and not the PDA and not passing the DNS requests... Either way, I tried to ping google via 74.125.45.100 and got back a request timed out. I am now wondering whether or not this may have to do with the packet MTU and whether or not the PDA packets differ from regular PC/WinXP packets. I just don't know enough about networking to be able to know. I am able to ping the Fuze gateway (for all-intensive purposes set to 192.168.2.1) and get back replies within 2-4ms. I really would love to hear from someone to whom this has happened before. I haven't called AT&T yet as the data connection on the phone itself works just fine, and I am able to load pages on the phone just fine. It's just any form of ICS that's beat...
Come on XDA-Dev, I know the collective intelligence can come up with something here.
I didn't think ATT could detect the difference between tethered requests and ones that originate on the phone, that would be bad though, if that were the case. Since the previous poster was watching videos, it seems to me the bandwidth would be the comparable to watching videos with the YouTube app on the Fuze, which I'm sure is within the terms of service contract.
My experience is closer to vovan75's. ICS works fine via USB, but does not work via Bluetooth. The strange thing is with the BT connection, I can ping the gateway, and even do nslookup with the default DNS, and sometimes if I get lucky, the connection works for a few seconds, allowing a page to load, totally random.
I thought everything worked using the original ATT rom, so I have a feeling culprit is something in the NRG rom, or maybe a radio incompatibility. I might re-flash to the old official rom just to try this, before the next time I update to the latest NRG build.
My setup:
Fuze with EnergyROM (July 22 build)
Radio: 1.14.25.35 (from official HTC 6.1 update)
Notebook with Windows 7 RTM
Windows calls this "Bluetooth Network Connection" (I don't see a reference to DUN, at least not in Win7)
ICS using BT (not working):
IPv4: 169.254.46.56
Gateway: 169.254.247.172
ICS using USB (working):
IPv4: 192.168.0.102
Gateway: 192.168.0.1
Windows 7 calls this "Remote NDIS based Internet Sharing Device"
DSLReport speed test (Flash) - down: 696Kbs, up: 336Kbs (varies quite a bit, much better at night of course)
Okay, figured it out. The DHCP setting for the bluetooth PAN should be off (I know, counter-intuitive). I found this by diff'ing the entire HKLM-Comm registry branch of the last EnergyROM build (Sept 6) vs the official ATT 6.1 rom (5.11.502.2WWE), which did work after all.
Code:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\Comm\BTPAN1\Parms\TcpIp]
"EnableDHCP"=dword:00000000
BTW, you don't need to setup Dial-Up Networking when using the Internet Sharing application (IntShrUI.exe). DUN needs to be configured on the PC when using the phone's modem bluetooth service, and AFAIK, needs to be provisioned by AT&T before it will work. The Internet Sharing app acts like an uplink for paired devices in the bluetooth personal area network (PAN).
rasterX, you rock! That little illogical registry fix is all I needed... I'd been banging my head against this Bluetooth DUN thing for days.
Thanks!

G1 won't connect to wifi

So I just rooted my phone today at my friend's house, I used his wifi just fine, no hickups. I don't have a service plan at the moment, so the only way I'm even using it is over wifi. Well when I got home, I tried connecting to my wpa2 secured network and I can't connect. What happens is the phone recognizes my network, I put in the passkey and it just sits and does nothing. I connected to it before I rooted my phone (and then this started happening once I changed some settings, but I figured it'd be a moot issue once I rooted.)
So far I can't get it to connect.
Any ideas as to what's going on?

"Wireless Tether for Root Users" app won't stay connected

Does anyone else have this problem?
My laptop will stay connected for a maybe a minute at a time, sometimes just a few seconds and I have to reconnect. Under Wireless Network Connection, the network is listed as "On Demand", if that helps.
I've tried every version of "Wireless Tether for Root Users" I can find and they all have the same problem. Is there anyway to stay connected?
Is it possible that your computer won't let you connect to an Ad-hoc connection? Maybe as soon as it realizes what it's connecting to it jumps off?
Havent had a problem, are you using the administration portion of wireless thether, you might have to just confirm the connection on the phone and apply the settings, you should have a green sheild when on your phone when a allowed device is connected
As far as I know ad hoc networks are allowed, I am using windows xp.
I have access control on and my laptop is allowed and connects fine, it just will not stay connected.
I am using a Toshiba nb205 netbook with windows xp.
On the Choose a Wireless Network window, next to G1Tether it says "On Demand" instead of Manual or Automatic. I've never seen that before.
I'm using the internet fine, I just have to reconnect every 30 seconds or so. Perhaps my google skills are too weak, but I cannot find anything, any help is very much appreciated.
Can you connect to a wifi network from the phone and stay connected?
Can you connect to a wifi network from the laptop and stay conencted?
"On Demand" is normal for Ad-Hoc Networks.
I had the same problem after upgrading from fresh 1.0 to 1.1 w/ gk-31. I uninstalled wireless tether and reinstalled it from my mybackup pro app backup (the one I made before flashing the new Rom and kernel. Works just fine now.
If I'm not mistaken I believe flipz included a newer version of wireless tether, maybe the old one works better.
I just realized I assumed you are using freshrom...
Might try reinstalling it anyways, let us know how it works out.
Reinstalling didn't work. I'll try out some roms tonight and see if they work any better, thanks anyways
Old post I know, but just wanted to see if anyone had any more ideas here. I don't think it's an android app issue at all, but rather windows. I'll be cruising along the highway with a fine connection, but as soon as windows picks up a random access point, it will jump off my ad-hoc connection and try to connect to the other one. not cool.

Problem with internet sharing and wi-fi router

I've got hd2 from virgin mobile. Till today wi-fi router worked ok, but now after launching I can't see it in wireless networks on my laptop even though program states is ready to accept connections. Internet sharing never worked, after pressing "connect" it grays out for 3 seconds and stays disconnected. I've used internet sharing previously on HTC HD with no problems though. So I don't know if it's a network problem or something else. I haven't used my data limit yet, so that is not the case. Using internet from the phone also isn't a problem. I would really appreciate some help.

Problem with internet sharing connection settings

I apologize if this has already been addressed. I looked, but couldn't find anything.
Here's my problem. I have a Tilt 8925 and WMWifi Router. My internet sharing connection settings are through Media Net. I have used this connection method for many months. Well, today, I connected my laptop through the WMWifirouter and everything was fine for about 5 minutes. Then my connection was lost, and upon trying to re-establish my connection, I notice that the internet sharing connection is trying to connect through AT&T ISP or something like that. I have repeatedly tried to switch it back to Media Net, but it keeps kicking back to the ISP setting. I have no way of connecting through ISP so, what happened and how do I fix it?
Thanks in advance!
Not sure if this is related or not. I never really paid attention to these settings before, so I can't say. If I look under the wi-fi connections settings tab on my phone, it brings up Configure Network Adapters. It is set to Virtual Ethernet Intermediate Miniport.......under that there are a whole bunch of other things. If I try to change it to IEEE 802.11b/g Compatible Wi-Fi Ad......, it appears as if it accepts the changes, bbut I then go immediately back into the settings and it is back on the virtual ethernet setting. Shouldn't I be able to change it, and could this possibly be why I can no longer connect using the WMWifiRouter?
Any help at all, please???!!!!
Even just a response of I'm not sure is better than no response at all.

Categories

Resources