Hey,
I am going to send my phone back to the warranty service because i have a very poor Wifi reception and dust under the screen...
But i have a custom ROM installed..
Do i need to instal a original HTC ROM??
And how do i unistal Hard-SPL??
I think you have to go back to original ROM, perhaps you can find it in the Wiki here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Topaz
Or in Topaz section
I allready have a rom from the HTC.com website, official
But how do i unistall Hard-SPL??
If you read the link I posted above, there is a section on how to hardspl
Extracted: NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs. also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is posted here below. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL.
Related
Thanks you all genius for bringing so much fun to the world.
Back to the topic. I've one TyTN II with original HTC CHT 6.0 ROM with it. I want to change it to the original HTC WWE 6.1. Without using HardSPL, is it possible to work it out in the following way?
1. Extract the SPL in the original WWE ROM
2. Use SSPL-KAIS to flash the SPL into Kaiser
3. Flash the ROM
Referring to sirsycho's guide http://forum.xda-developers.com/showthread.php?t=335568, it said the ROM should be flashed first for reverting back progress, but without putting HardSPL in it, how to get it done? Or should the progress be
1. Apply HardSPL
2. Flash
3. Write the original SPL back using SSPL-KAIS
Thanks very much for your guidance
***
Actually I found this note from speedbird http://forum.xda-developers.com/showthread.php?t=397550
In fact I should follow up the post.. sorry for opening a new post...
Anyway just want to ask if it is possible to revert back to the original HTC SPL after the flashing progress (or as the final step)?
or is HardSPL the must during the whole procedure?
Thanks
hardspl is for mostly flashing cooked roms. if u r upgrading a official rom by htc to another official rom by htc (for same device) u don't need hardspl.
but it is good to have.
Can the original Stock ROM from HTC be installed without changing the original SPL (with olipro's Hard SPL ) ? 10x in advance
Yes you can, BUT only if you find the rom in the HTC e-club when you signed in.
If you want to forexample use the HTC official roms from the forum you must use HardSpl. Fine example is the 1.28.457.2 rom which is official but it is the Asian version, that you cant flash with orginal spl.. Someone who now this for 100% can correct me if im wrong. iIm only 99% sure
Hey, I just got my Fuze yesterday, and I'm loving it. I just have a question that I couldn't seem to find by the search.
How would I go about returning the Fuze to the stock SPL after flashing it to HardSPL? I'm asking just incase I need to return it. Would I just flash the default AT&T ROM to restore everything? Or does more have to be done? AKA Do the directions in the Hard-SPL thread apply to the Fuze?
Sorry if this is a dumb question--it's been a while since I've owned a WM phone. (Wizard to be exact =])
NVM Found the answer.
Here for those that want to know:
No need to have the SPL 1.95...I had to exchange my Fuze today because of a problem with buttons...
Just follow the steps on the front page and then afterwards reflash the stock att rom(the one with SPL 1.95)...it will flash SPL 1.95 with it
confirm by going into bootloader
Click to expand...
Click to collapse
what front page? i want to reflash to oem to exchange for a new fuze
hard spl has overwrite protection. you will have to flash the unsigned spl to overwrite ti (just search for "stock spl"). However, my question is, if you flash the stock rom, do you have to go thru flashing the original spl as well or the hard spl will work with the stock rom as well?
thank you all!
I want to know what my phone should look, so that I can change it back in for a warrenty.
And is there a video out to show how to STOCK SPL - FOR WARRANTY REASONS ONLY.
Can you please provide all the information that is needed so that I will not be charge or mess over my contract. Thanks.
If you have HARDSPL installed then your boot screen shows 1.90olinex if you are at STOCK SPL then it shows 1.90.
Before I returned my phone I flashed the HTC ATT ROM that includes radio, then I flashed it with STOCK SPL to return my bootloader from 1.90olinex to 1.90.
That is as much info as I can give you without doing searches of the forum. I think you can handle a few searches from here. Just look for Stock SPL and use the Wiki.
hi to everyone especially the english speaking people i,m having a problem i,m in sweden i bought a D2 unfortunately i cant change the language to english well i know i can crack it and flash a WWE stock or cooked rom ........but in doin so will void my 24 months warranty i dont want to do that........so i,m gonna ask a big favour if someone could just let me use their serial number from 1 of their english D2 phones to upgrade my phone to english from htc english site that would be great
please..
thanks in advance
No, you can run HSPL on your TD2 without any worries.
If you want to keep the warranty read this:
Hard-SPL Unlocker for Topaz - Released! Now New Update to HSPL 1.83!
"NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs. also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is posted here below. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL."
Enjoy
If you need, here you can find serial numbers:
http://forum.xda-developers.com/showthread.php?t=568330
Hi,
when i flash my TD2 it says i have already done the hardspl before on another device... what should i do???