[TUT] i600 WM6.1 Upgrade Guide - Non-Touchscreen Windows Mobile Other

Ok guys I'm go to show you step by step how to upgrade your Samsung i600 to Windows Mobile 6.1 If you need any help PM me.
First of all download and install Active Sync 4.5
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/activesync-download.mspx
Now go to this thread and download your version of WM6.1 I will be using version 2.0 for this tutorial.
http://forum.xda-developers.com/showthread.php?t=493663
Download this file WCE DOWNLOADER
http://www.host10mb.com/AfBSzx
Download Samsung Modem Drivers and were set to go
http://www.host10mb.com/KBs1VY
Install Active Sync 4.5 first
Extract your Windows Mobile 6.1 version that you downloaded and REMEMBER WHERE YOU EXTRACT IT TO ! It will create a file called pda.bin
Unzip and install the Samsung Modem Drivers you downloaded
In Active Sync disable USB Connections by unchecking the tick in this box-
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Open up WCE DOWNLOADER -
Click PDA -
Open the pda.bin file you download and extracted ( Windows Mobile 6.1 )
Turn your phone off
Plug in the USB Cable
Restart the phone in Bootloader mode
It will start in bootloader mode
Windows will recognize the device and run the Samsung Modem Drivers you installed earlier
When it says device found in WCE DOWNLOADER. Click Start Download
Downloading percentage
All done
Say thanks if this helped you out
If you need any help
PM me
Cheers

i have follow all the step above but i got stuck in the ultra messaging logo .please do advice thanks

kiplingmerah said:
i have follow all the step above but i got stuck in the ultra messaging logo .please do advice thanks
Click to expand...
Click to collapse
Turn your phone off an on again. Wait for about 5 minutes. If it does not load then phone turn the phone off.
Try to flash the phone again. Make sure ActiveSync USB Connections are disabled and that the Samsung Modem Drivers are installed!
Let me know how you go.

kiplingmerah said:
i have follow all the step above but i got stuck in the ultra messaging logo .please do advice thanks
Click to expand...
Click to collapse
u should try to flash the eboot and phone part too, its works for me

for asia version (indonesia) 1# u need to flash it to china version WM6 then flash it use nokser's rom. though you flash it to samsung official rom (indonesia), it will be stuck in logon.

thanks guys .. for the advice .. i will try again and post it here the result thanks

thanks guys .. for the advice .. it work bt fone stuck any help

Thanks guys finally i got already winmo 6.1 on my samsung i600 thanks to all of you guys i really appreciated Well done

Here is how to disable Threaded SMS:
Code:
[HKEY_CURRENT_USER\Software\Microsoft\Inbox\Settings\OEM]
"SMSInboxThreadingDisabled"=dword:1 -> Change to "0" if you want to Enable Threaded SMS
and here is how to have SMS Sent Notification :
Code:
[HKEY_LOCAL_MACHINE\Software\Microsoft\Inbox\Settings]
"SMSNoSentMsg"=dword:0 -> Change to "1" if you want to Disable SMS Sent Notification
Use any Registry Editor software to edit that guys

deleted---

Im usin Window Vista.... so i cant use activesync 4.5
instead im usin window mobile for vista... is there any solution to it? i dont wanna brick my 1600...

Instal WMDC for Vista

Hello,
Do I actually need wm6.0 before installing wm6.1? Because its getting very difficult to get the files you need for a wm6 upgrade

Hi bro kipling...jadi cara mana yang berhasil...pake cara indomano atau aaofik...soalnya problem yang sama menimpa diriku, mentok di logo ultra m...dan suara ngeeeng...abis tu ya udah hang....

Working all
Hi nokser...do tou have rom wm6 or wm6.1 that working good for all like bluetooth, wifi, camera, wm, etc....give me recomend...with one?...sory for bad english....

Upgrade Compatability
Thanks for this.
1. I have a 'blackjack' phone running pda and phone software 'i600JIHB2'. Can I use the above guidance and upgrade to win 6.1 (currently on win 5).
2. The phone has Wifi and I have read elsewhere that the upgrades can stop wifi functionality. Is this true?
3. If my phone is locked to a network, will this be affected by the o/s change?
Thanks in advance

moxy1975 said:
Thanks for this.
1. I have a 'blackjack' phone running pda and phone software 'i600JIHB2'. Can I use the above guidance and upgrade to win 6.1 (currently on win 5).
2. The phone has Wifi and I have read elsewhere that the upgrades can stop wifi functionality. Is this true?
3. If my phone is locked to a network, will this be affected by the o/s change?
Thanks in advance
Click to expand...
Click to collapse
Any advice>>>>>>? (see #16 above)

still stucked
kiplingmerah said:
Thanks guys finally i got already winmo 6.1 on my samsung i600 thanks to all of you guys i really appreciated Well done
Click to expand...
Click to collapse
hello, how were you able to get through with it because i'm still stucked to the ultra messaging window? please help. thanks

callumogrady said:
Turn your phone off an on again. Wait for about 5 minutes. If it does not load then phone turn the phone off.
Try to flash the phone again. Make sure ActiveSync USB Connections are disabled and that the Samsung Modem Drivers are installed!
Let me know how you go.
Click to expand...
Click to collapse
hello sir, i did everything that you said and reinstalled it again, buy I'm still stucked... pls. help, i think i just killed my phone... thanks

indomano said:
u should try to flash the eboot and phone part too, its works for me
Click to expand...
Click to collapse
how do you do it? because it says that it's invalid image? thanks

Related

My O2 Mini is dead, poor me please

Just got O2 Mini (second hand), when id upgrade it with MA_O2Asia_11100_922_11100_Ship, my stupid pc have restarted (i leave my pc when it starts to upgrade), so now my o2 mini get stupid too (sometimes it goes to setting wizard (tap here, tap there bla bla bla) then restart again, sometimes it wont go anywhere (just blank with red led), sometimes it goes to Serial mode (if I recharge it) and it goes to USB mode v1.00 if I connect it to my d4mn pc, last, it just got blank with no text or graph) Ive disable connection with ActiveSync (I use 4.2) via USB, and also ive terminate wcescomm and rapimgr. Thats the explanation.
Its there en luck to revive my mini again ?? Please, help me coz i cant give it back to the seller in that condition.
1.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2.
3.
4.
5.
did u try reflasing in USB mode? what happens there? if it goes thru is it still acting up?
Nope, nothing happen and the usb device doesnt recognise by pc
try bootloader mode upgrade?
http://wiki.xda-developers.com/index.php?pagename=MagicianRomUpgrade
hanmin said:
try bootloader mode upgrade?
http://wiki.xda-developers.com/index.php?pagename=MagicianRomUpgrade
Click to expand...
Click to collapse
As you can see in my first image, there are two exe files : MaUpgradeUt_noID.exe and ROMUpgradeUt.exe, both of them cant work, even the file from the link that youve gave above.
Is my bootloader exist or not ??? and y windows cannot recognise my device, eventhough the activesync had installed ?
Note :
Ive remove the v4.2 of activesync and reinstall with v4.1.0 b4807
Strange act happen again .... suddenly my mini has wake again .... it looks like normal, at the restart (after auto config), it sleeps again.
At the sudden wake, my pc still doesnt recognise it. Hmmph .... can i have en hope ??? Oh, God send me PPC Angel
This is what ive got when my mini has wake for a while :
ROM version 1.03.00 WWE
ROM date 11/01/04
Radio version 1.01.00
Protocol version 1337.38
ExtROM version 1.03.166 WWE
Please, i dont mean to insist, but can en1 provide me a good way to solve my problem ? an opinion, a troubleshooting or en suggest ? I can think nomore, ive try most of the ways, thereis one secret weapon that i dont use, but this is the last hope ... teach this d4mn phone how to fly ... :twisted: :twisted: :twisted:
Helloooo, anybody there ?????
Try using another USB cable..
Already try with 5 usb cable without luck ... do u know exactly what happen to my mini ???
Hi bro
its Faisal from Quetta, Pakistan
I know exactly whats wrong with ur Magicians
its not the rom
its not the cable
its ur "usb connector" where u insert ur cable.
sometime it gets rusty or sometimes the inner multi layer circuit board connections breaks
simple thing to do:
if u know how to hardware.... than first thing u should do is to put under the magnifier lamp n try cleaning those small 5 pins in that usb connector after removing the battery
if no success than change the usb connector with hot air tool or SMD
if u cant do that, get it done by some hardware guy
than get ur battery charged somehow and insert the charged battery
Press Camera button + Power Button and insert ur stylus in the reset switch to go in the bootloader mode
download universal flashing interface to load the rom like a country error fix and with that you should be able to upload any magician rom from german to arabic
If u get your solution this way than please Pray that i find someway to fix my not working mic
Take care n best of luck
Regards
Faisal
+923003812680
+923218014276
yeah hope that tip is work !
To My God ,i Have The Same Problem.and It Sees Being Unnormal, It Can Enter The System Must Be After I Cut Off The Power .if I Restart I Was Be In The Screen Of Boot And It Showed "series 1.02"
I Also Can't Flash The Rom In Usb.i Think Flash Rom In "sd" Way Can Slove The Problem But I Didn't Backup The First 416 Of The Rom So I Can Flash Rom Again ,and So I Can't Work.who Can Help Me .thx

Phone isn't reconized in Windows Vista

Hello members,
I recently bought a new PC, running on Windows Vista Ultimate. I had to install Microsoft Mobile Device Center for syncronization (instead of Active Sync for Windows XP), so I did.
As far as I know I installed it the way it should be.
So here come's the problem;
I wanted to flash a new rom, so I connected my device to my pc to establish a connection with Microsoft Mobile Device Center,
but the phone isn't even reconized in Vista, therefore I can't flash a new rom on the device.
I tried al my USB ports and did a hard reset on the device, but that didn't work.
The phone is a MDA Vario 4, with MRom 1.63. I never had problems on XP with synchronizing so im pretty sure the Rom is not the problem, but I don't know what is..
How can I fix this so I can flash my device using WMDC in Vista
32 or 64bit vista ?
Rudegar said:
32 or 64bit vista ?
Click to expand...
Click to collapse
I have 32 bit Vista.
It works great with Window Vista Home Premium 64bit. Is your settings familiar with mines?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i think this might help you, im assuming that your phone is recognized as a when you want to sync it but when you want to flash a rom it will not find the phone, if this is the case here you go http://forum.xda-developers.com/showthread.php?t=291723, hope it helps
try unchecking that checkbox for enable quick ....
Depending on whether it is if you want to flash or not...
If it is just to sync, I had this problem too and the solution was to delete the profile in ActiveSync on the phone and then reconnect. (I think - it was a while ago).
As per the first pic in xhypnotik's post, try unchecking the box for "enable faster data sync". If this doesn't work, try deleting the profile on the phone...
I had a similar issue. See if running Windows Update on Vista works. For some reason the driver for Device Center didn't automatically download for me. It was on of the updates under Windows Update though.
Before I start, thx all for your reply's, your help is much appreciated.
xhypnotik said:
It works great with Window Vista Home Premium 64bit. Is your settings familiar with mines?
-IMAGE-
-IMAGE-
-IMAGE-
-IMAGE-
Click to expand...
Click to collapse
I have the same settings, but nothing happens when I connect my Phone to PC.
rmjjjt said:
Depending on whether it is if you want to flash or not...
If it is just to sync, I had this problem too and the solution was to delete the profile in ActiveSync on the phone and then reconnect. (I think - it was a while ago).
As per the first pic in xhypnotik's post, try unchecking the box for "enable faster data sync". If this doesn't work, try deleting the profile on the phone...
Click to expand...
Click to collapse
MimoG3 said:
i think this might help you, im assuming that your phone is recognized as a when you want to sync it but when you want to flash a rom it will not find the phone, if this is the case here you go http://forum.xda-developers.com/showthread.php?t=291723, hope it helps
Click to expand...
Click to collapse
Thx for your reply's, but my phone isnt reconized at all. So I can't do anything at all on my computer, no flasing, no synchronizing, I can't even acces the phone's memory card, even if I select the Disk Drive option.
As soon as I connect my phone to my computer Windows Vista just says,
"The usb device is not recognized".
sto110 said:
try unchecking that checkbox for enable quick ....
Click to expand...
Click to collapse
Tried this to, didn't did anyting to
mattyman said:
I had a similar issue. See if running Windows Update on Vista works. For some reason the driver for Device Center didn't automatically download for me. It was on of the updates under Windows Update though.
Click to expand...
Click to collapse
I did an update just some moments ago, it installed some updates, but it didn't install any update's for the WMDC..
I took the check mark off "Enable Advance Network Functionality"...seemed to recognize my Fuze
smittyj26 said:
I took the check mark off "Enable Advance Network Functionality"...seemed to recognize my Fuze
Click to expand...
Click to collapse
Vista still not reconizing. It just shows the unknown device message when I connect it to USB, so there isn't anything I can do.
I made some screenshots of the message I get when I connect my device;
When I click on the message, I get the following screen;
When I go to my computer, there isn't any device I can click on..
Try plugging in some other devices instead of the phone into your USB port and see if that message appears. You might need to update your drivers or install it.
xhypnotik said:
Try plugging in some other devices instead of the phone into your USB port and see if that message appears. You might need to update your drivers or install it.
Click to expand...
Click to collapse
Did that too. I tried an external HD storage device, an MP3 player, and my printer, which is USB connected. Al devices are working properly, except the phone. When I connect it, and want to install drivers for it, it simply just says, that there aren't any available.
I fixed the problem.
Very weird, I accidently tried another USB cable and that did the trick. It installed all the drivers automatically and now the device is reconized, so problem is solved.
Thanks everyone for your input!
AjiNn said:
Hello members,
I recently bought a new PC, running on Windows Vista Ultimate. I had to install Microsoft Mobile Device Center for syncronization (instead of Active Sync for Windows XP), so I did.
As far as I know I installed it the way it should be.
So here come's the problem;
I wanted to flash a new rom, so I connected my device to my pc to establish a connection with Microsoft Mobile Device Center,
but the phone isn't even reconized in Vista, therefore I can't flash a new rom on the device.
I tried al my USB ports and did a hard reset on the device, but that didn't work.
The phone is a MDA Vario 4, with MRom 1.63. I never had problems on XP with synchronizing so im pretty sure the Rom is not the problem, but I don't know what is..
How can I fix this so I can flash my device using WMDC in Vista
Click to expand...
Click to collapse
Could you please check your outlook? maybee this has the problem. i told you this, because i have same problem, and my problems root beggin from outlook!!!

[ROM] [Samsung SGH-i600] [WWE] WM6.1 build 17944

Update Windows Mobile 6.1 for SamSung I600
Get these runtimes and install on your PC (Windows XP & Vista): vcredist_x86.exe and NetCF 2.0
1) Connect your phone to the PC, and Sync,
2) After complete synchronization, turn off the phone.
3) To create a directory RomUpdate PC and copy it to WM6.1 - file pda.bin and WCEDownloader_v1[1].1Single.exe
4) Run program WCEDownloader:
In the PDA
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Select file pda.bin
5) Move in the BL with the phone connected to a PC.
Waits to see moments in the main window, running the program on the PC:
Code:
[StartDownload => 0] StartDownload!
[PDA] Connect and Power-on the Device.
[PDA-0] Driver Opened.
[PDA] Read Wait. = [0]
[PDA] Read Done. = [0]
[PDA] Device Found. = [0]
When this is possible after the above steps click Start Download
Wait about 15-20 minutes, and our Smart should now restart automatically.
Key Option's To DownLoader
Key Option's To DownLoader
I have an i600 that was flashed with i607.
Can you help me get it back?
You Update i600 rom for i607
nokser said:
You Update i600 rom for i607
Click to expand...
Click to collapse
Yes it's a SGH-i600 that was flashed with the AT&T (607) rom.
Now all it does is boot up (wm-splash, at&t splash, then at&t goodbye splash)
When I put it in BL mode it states (USB Downloader at&t)
This is probably the end of your phone ....
nokser said:
This is probably the end of your phone ....
Click to expand...
Click to collapse
That's what I feared/
Give me some time and something to help, but you have to be patient.
Now, as the elevator went out the official 6.5 - is a slight confusion
nokser said:
Give me some time and something to help, but you have to be patient.
Now, as the elevator went out the official 6.5 - is a slight confusion
Click to expand...
Click to collapse
It's a friend of mine's phone (I am trying to help him), I will forward this to him and let him decide what to do.
Tell me, you can enter into an option Bootloader
It's not work! I'm conect the phone in BL-mode but WCEDownloader says that phone not connecdted (((((
You see...
First - Run program,
Two - connect I600 to USB
hi nokser, where can i download New Windows Mobile Developer ® 6.5 OS 5.2.21234 Build 21234?
otherwise, my version of Windows Mobile Developer ® 6.1 OS 5.2.17944 Build 19208
cannot recieve files using bluetooth. any idea?
thx
Yes I have, in the new version ....
And wm6.5, you wait a bit, because I do not have new drivers for the keyboard
you mean in version 6.5 or still in 6.1
if still in 6.1 give the link to download then.. thank you,
No problem
nokser said:
Update Windows Mobile 6.1 for SamSung I600
Get these runtimes and install on your PC (Windows XP & Vista): vcredist_x86.exe and NetCF 2.0
1) Connect your phone to the PC, and Sync,
2) After complete synchronization, turn off the phone.
3) To create a directory RomUpdate PC and copy it to WM6.1 - file pda.bin and WCEDownloader_v1[1].1Single.exe
4) Run program WCEDownloader:
In the PDA
Select file pda.bin
5) Move in the BL with the phone connected to a PC.
Waits to see moments in the main window, running the program on the PC:
Code:
[StartDownload => 0] StartDownload!
[PDA] Connect and Power-on the Device.
[PDA-0] Driver Opened.
[PDA] Read Wait. = [0]
[PDA] Read Done. = [0]
[PDA] Device Found. = [0]
When this is possible after the above steps click Start Download
Wait about 15-20 minutes, and our Smart should now restart automatically.
Click to expand...
Click to collapse
i have follow all the step above but i got this error message
[StartDownload => 0] StartDownload !!
[PDA] Connect and Power-on the Device.
[PDA]Device Not Found.
Click to expand...
Click to collapse
version
PDA: i600UDXGJ1
PHONE:i600UDXGJ1
H/W: MP 1.901
what should i do please do advice.Thanks in advance
Now you first option - run program
Two option connect I600
sequence is important
nokser said:
Now you first option - run program
Two option connect I600
sequence is important
Click to expand...
Click to collapse
ok i will try it again . report the result thanks
Feedback
Does wifi,mms work properly?And is there MSN messenger in the updated rom?

[DEV] KDZ Firmware Update Fix

Problem:
Latest Version of LG Mobile Update prevents uses from updating firmware from kdz files.
Info:
As LG Tools relay on lg webserver to provide application updates and firmware updates it's not possible to just use the old version as it force fully update it self.
Solution:
I used network sniffer(Wireshark) to sniff all the traffic between application and LG Webserver i tracked the important urls and the data coming from LG Webserver. I created all the files with same names and with data from LG Webserver. I changes the LG Mobile Application from 1.5.4.9 to 1.5.4.8. Rest of the files has same data as LG.
How To:
1) Download http://smallsrv.com/
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2) Install
3) Go to Settings
4) Go to HTTP Settings
5) Change Port to 9002
6) Extract the Content of Attached Zip file into C:\shttps\www
7) Edit C:\windows\system32\drivers\etc\host in notepad and add the following Line
127.0.0.1 csmg.lgmobile.com
8) Enjoy Flashing firmware as usual
http://forum.xda-developers.com/showthread.php?t=1287236
Note:
This method has lot of advantage
-LG Is watching everything when you run firmware update with KDZ Method lg is logging everything you mobile No, SN No, OLD Firmware, New Firmware etc..
Thanks:
If you have any questions or need any info feel free to ask i will try my best to help.
If you like my work Donate
This is pretty awesome. I had exactly that problem when I tried do downgrade to FroYo because of the Gingerbread Baseband issues.
That wonderfull moment community finds an flawless solution to bypass permanently the control of a company on OUR phones that we paid them the big price for.
Sincerelym
For the time you used and for your generosity sharing it
THAAAAAAANKS
Thank you very much.
Delete everting of LG DISCONNECT your internet start up lg tool
Close it
Connect to internet
Install drivers
Flash tool works for me
Sent from my LG-P920 using XDA App
no way to download shttp. . . goes to 145kb of 146kb and stops.. tried several browsers and same thing happens
Bayrich said:
no way to download shttp. . . goes to 145kb of 146kb and stops.. tried several browsers and same thing happens
Click to expand...
Click to collapse
I have added shttp as a attachment to my first post.
Sorry for the stupid reply... I had already flashed my phone with v21v using the kdz method, am I to understand this is not possible anymore because newer versions are available? And this allows us to flash the older versions again? so in theory I could try v20b and go back to v21a or v10 or whatever I wanted...?
Amazing works perfect !!
Thank´s
I did everything step by step.
Now when I run Lg Update tool,it stucks.
And the updater shows the message in the attachment.
What did I do wrong?
Solved.
Damn!!!!!!!!!!!!!!! I'm getting crazy...everything goes fine until the update....suddenly my cell phone turn off and a receive a messege:
problem with communication between cell phone and PC.
please disconect the cable from your phone and remove and connect the battery.
power on your phone and press restart button to resume update.
But is the same **** all time!
any help?!
titijr said:
Damn!!!!!!!!!!!!!!! I'm getting crazy...everything goes fine until the update....suddenly my cell phone turn off and a receive a messege:
problem with communication between cell phone and PC.
please disconect the cable from your phone and remove and connect the battery.
power on your phone and press restart button to resume update.
But is the same **** all time!
any help?!
Click to expand...
Click to collapse
Which Method are you using
KDZ file?
LG Recovery?
LG Firmware Update?
unknown_world said:
Which Method are you using
KDZ file?
LG Recovery?
LG Firmware Update?
Click to expand...
Click to collapse
the method in this topic + UpTestEX_mod2_marwin
titijr said:
the method in this topic + UpTestEX_mod2_marwin
Click to expand...
Click to collapse
Try connecting phone in download mode
Press Vol Down and Connect Cable or Press Vol Up and Connect Cable
I did't remember correctly which one is it.
Can this method work for optimus black too??
vincevince55 said:
Can this method work for optimus black too??
Click to expand...
Click to collapse
There is no device specific files so i think it might work
Hey unknown_world,
big big thanks for this - it works just fine!!
Here is a video how to use it.
http://www.youtube.com/watch?v=xGl8mJXxyFo
Greetz paki
paki I saw your video...
on 0:30 mine is different...where did you get the log file!?!??!?
I don't have it....I got the zip file, put the files inside de WWW folder...but I don't have log file...
Hi
you have to create one.
Make a new txt-file and call it "log.txt" - then you have to delete the ".txt" - that's all
Greetz paki
I created one...but it's wierd...it's a text file...how I can change that? I've noticed that you log file is a data file...
I'm completly mad!!!!!
this crap says: "usb device not recognized" (unknown device) when I put on usb cable...
I installed all drivers...What can I do now? I'm close to smash this on the wall!!!!!!
where I can get the drivers? since I edited the host file...and I can't do anything on LG sites...
please help, before I do something crazy!

[Tool]LG-P920 Optimus 3D (Thrill) Recovery Toolkit (only Froyo/GB)

Hi guys,
I made a little tool which you can use to install your favorite recovery-system to the LGO3D.
Here it is:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download: LG-P920_offline_Recovery-Toolkit_XDA-Edition.zip
md5: 6E3C8CEE5989302C5C333D6491E9373E
Recovery images and instructions are inside the tool.
The version is called "XDA-Edition" because the integrated help links are going directly to this thread.
All credits for the recovery images goes to their developers - LG Electronics or the Clockworkmod-Team - Thanks!!
Have fun!
Greetz paki
Thanks man..
great
doubt
hdk1984 said:
great
Click to expand...
Click to collapse
works on p920h Baseband 20A
Awesome! Thanks!
Please cross-post this to the LG Thrill Forums, it would be much appreciated!
Thanks! It's very useful and simple tool. There is a similar non-GUI tool called Recovery Manager but I can't use it (I am getting messages like "adb server is out of date. killing.../ failed to start daemon" etc). I hope that with your tool, I won't have similar problems.
If CWM is already installed, can I install/flash over it the Stock Recovery or the CWM-Touch? And later, re-flash and go back to CWM?
Hi,
I tested the tool many times before and I've never had problems with a running adb-server.
You can change the recovery sytem as often as you want by replacing the old one.
greetz paki
Hi and thanks for the quick reply. Unfortunately my O3D has a problem with your tool, like with the other similar tool (Recovery Manager).
Some time ago, I installed the CWM-Touch with another tool you've posted here, and now I want to go back to the CWM no-touch version. I just used your new tool trying to flash the CWM, and everything finishes successfully (First I get a window that says "waiting..." and then another one that says "success.. done" or something similar).
But when I reboot to the recovery, I still have the CWM-Touch version. I tried already with your tool 3 times to flash the normal CWM and 2 times the LG stock recovery and even if it says that they flashing went successfully I'm still stuck to the CWM-Touch.
Do you have any idea why my phone is stuck with the CWM-Touch? Could it be a corrupted file somewhere like the Superuser binary (I have the latest version)?
Hi,
maybe your pc-firewall is blocking "adb-win.exe" - please check this!
Please open the windows taskmanager and kill all processes like "adb.exe; adb-win.exe; adb-windows.exe".
After that you can make a new try to flash the stock-recovery.
The Version of SU doesn't matter.
The success message also appears when the operation is canceled due to connection problems.
I know that the tool is not yet perfect, but this is my first attempt at a GUI. I try to eliminate the errors in a next version.
greetz
I works!
Great!
Thanks!
Thanks again for the quick reply. The adb***.exe processes are always killed when I exit the tool and I turn my (default) Win7 firewall temporarily off during the flashing attempt.
I'm almost certain that this is not a problem of your tool but of my phone. Because the same happens when I try to flash any CWM or stock recovery with the other similar tool, the Recovery manager.
Try to reinstall the USB-driver-package - maybe there is the problem?!
http://www.mediafire.com/download.php?eec7g8dekfggwag
USB-debugging is activated?!
greetz
Thanks. Yes, the USB-debugging is on all the time.
I installed the USB-driver-package from the link that is provided when you start the recovery toolkit.
I suppose that the link in the toolkit is the same one you've posted above but I'll uninstall it, reinstall this one and try again.
Yes - it's the same file!
Please use a different USB port of your PC so that the drivers are installed from scratch.
Which Windows-system do you use?
Thanks. I'll better use not only a different USB port but a different PC as well.
All the attempts so far were done from my laptop with Windows 7. My PC has Vista and I also can try it from my second laptop with WinXP.
I'll test it and let you know. Thanks.
OK
If you are using a Windows7/Vista PC with original firewall, then I recommend you this tool. With it you can control the access of programs.
There is a free version that goes for first.
Good luck - greetz paki
YES! It worked!
I installed the LG USB-driver-package on the PC with the Vista, and the CWM no-touch version was installed successfully with the first attempt!
Thanks a lot for your help and your prompt replies!
Grüße
It's my pleasure!
greetz paki
Hello there, took notice of your application here and did a short write up for it on the XDA Portal.
here's the link:
http://www.xda-developers.com/android/tool-for-the-optimus-3d-installs-your-favorite-recovery/
I had written more, but my editor thought it prudent to edit out some of it. regardless, i hope you enjoy it!
PoorCollegeGuy said:
Hello there, took notice of your application here and did a short write up for it on the XDA Portal.....
Click to expand...
Click to collapse
Thank you very much. This is a great honor for me!
Greetz paki

Categories

Resources