if the handsfree is connected i can hear anyone who calls and they can hear me... if i remove it... no would both ways and no speaker either.
how can i solve this... is there someway i can disable the handsfree function by software and enable it whenever i need it?
Warmie
hi and welcome to the forum.
well you can try to upgrade the radio rom. it might solve the problem. if it doesn't then it should be a hardware problem..
here you can find radio rom
http://vidmes.com/xda/Uni/Radios/
here is the guide for upgrading the radio rom...
http://wiki.xda-developers.com/index.php?pagename=UNI_Radio
This should help
Cheers
Rajiv
tried the radio upgrade
i tried the radio upgrade, still the same thing happens..
does anyone know which part of the hardware could be faulty or if any of the soldering was broken inside createing an open circuit somewhere.
Warm_ice
Its hardware!!
HI man!!
Im electronic technician, check your speaker with ohmeter, must be continuity (betwen 0 ohm and .300ohm) also check missplaced,unsolded or broken components in mother board and interfaz board (conection speaker board). If the speaker measure good and no missplaced components,,,sorry man the "Audio Codec Chip controller" are damaged
Sound Problem Too
Hi AIN1 i think u may help me too with an idea, My Imate Jasjar has a sound proplem; it stay with no sound all the time and sounds only when i tap/hit a little on front left speaker, i opened it up and removed the motherboard but i failled to find the loose part??? Pls help.
yeah
You haven`t sound in all of three speakers of your UNI??? (Two speakers on front and the speaker of phone?) this is bad you will need to fix the mother board, your last chance is: blow hard in the audio jack conector may be is in short with a metal residue from pin of handsfree or the internal pins of the jack conector are damaged. I think it is the problem, fin a reposal part to change it, go to a technical repairment for celular phones, may be need to adapt a similar or diferent part to fix it. Now Im sure is the jack conector check it plis.
When someone call you , does the device ring normally or still no sound , if so you have a little a problem with audio jack . I can explain after your reply .. sorry for bad english
sound problem fixed
ok... after the sound problem... it started giving me a "no sim found/detected" error
i got it fixed at an i-mate technician he replaced the handsfree socket and the controller IC ... presto... its running wild now less than 30$ to fix
Warm_Ice
Related
when making a call on my M500 people cannot hear my voice but I can hear them ok < is mic goosed(u/s ) or is there a problem with rom ?
i had that probelm on my Imate Jam initially thought the problem was with the mic, after showin it to a pro he checked it out and found out that the actual cause was some chip inside which was screwing up
the microphone he tried changing twice but it made no differance to the sound
but another person once told me that theres this little rubber around the mic that holds it in place that sometimes moves and covers the mic hence no one can here u not sure if that can happen in urs but its still an easy option compared to a dead/dying chip
Is there any hardware repair disscuss in this forum?
Or better, can some one share hardware schema XDA or DOPOD?
Is that illegal ?
Hence I never see any service manual/schematic here around.
thanks
hello.
i have a problem with my universal:
i can't get my speaker phone to work (the phone doesn't ring, and no sound can be heard (media player or any program)
the speaker located in the lcd works, so i can hear when i talk with someone
i temporarly changed both speakers with 2 that work, and there is the same problem.
i changed the rom, but no change
anyone have any ideeas about what the problem is ? (and perhaps a solution ?)
thank you.
maybe an internal bus break if you tested the connections with known working speakers
mmarza said:
hello.
i have a problem with my universal:
i can't get my speaker phone to work (the phone doesn't ring, and no sound can be heard (media player or any program)
the speaker located in the lcd works, so i can hear when i talk with someone
i temporarly changed both speakers with 2 that work, and there is the same problem.
i changed the rom, but no change
anyone have any ideeas about what the problem is ? (and perhaps a solution ?)
thank you.
Click to expand...
Click to collapse
I occasionally get this problem after I've used the headphone socket - it's as though the socket gets stuck and thinks that there's still a jack in there, and so mutes the external speakers. I find that pushing the kacj in again, giving it a wiggle, and pulling it out normally does the trick.
Cheers,
Steve.
mzalan said:
maybe an internal bus break if you tested the connections with known working speakers
Click to expand...
Click to collapse
yes, i tried with 2 speakers from my other uni (i'm sure they are working)
do you have any suggestions of how to fix this?
StevePritchard said:
I occasionally get this problem after I've used the headphone socket - it's as though the socket gets stuck and thinks that there's still a jack in there, and so mutes the external speakers. I find that pushing the kacj in again, giving it a wiggle, and pulling it out normally does the trick.
Cheers,
Steve.
Click to expand...
Click to collapse
i've just tried this with some headphones (i hear normally through them), but wiggling and pulling it doesnt do the trick
a broken bus? there's no way to fix it without a lot of expertise, knowledge and specialized equipment. Sorry...
the experience part is the one thing that i need
so.... the broken bus thing.... is a hardware problem that an authorised service can fix (for a lot of money, of course), but is fixable, right ?
thanks
StevePritchard said:
I occasionally get this problem after I've used the headphone socket - it's as though the socket gets stuck and thinks that there's still a jack in there, and so mutes the external speakers. I find that pushing the kacj in again, giving it a wiggle, and pulling it out normally does the trick.
Cheers,
Steve.
Click to expand...
Click to collapse
i do the same thing try a few times till you succeed try to pull the jack as though it is stuck
i've used a multimeter and found that the microswitch works fine, so unfortunatly that isn't the problem
Same fixed problem
I had this same problem, is the 3.5 mm jack, I fixed it by opening the uni.
Saludos
thanks. solve the problem.
I have some troubles with my headset input. It's broken down and i cant repair it. The main problem is that i cant talk through phone becouse device "thinks" that the headset is in... Loudspeaker doesnt work...
Whats the most funny in it? i can talk through devices microphone only with pluged headset. Simply, with pluged headset phone works normaly (i can listen to music,call, talk by loudspeaker)
I guess i will not repair it so is it possible to disable default headset profile, or disconnect, turn off this profile or headset input?
Im owner of Qtek 8310, WM6 Standard v3.7 (FINAL!)
Thx in advance, greeting
There's no software hack that I've heard of. I've always assumed that insertion of the connector into the jack was like flipping a hardware switch.
Maybe be brave and disassemble and clean out your phone? Check if something's jammed in the jack?
I've had such a problem couple of months ago. I sent my phone to the customers service and they replaced the jackplug. After replacing, all works fine.
well, as u can see im from poland. Where should i send my phone?
Can u give me an adress, please? How much is it if i tell them to repair that input and exchange cover? (my cover looks awful, its destroyed)
Thx for answers,
Well, I bought it online (via a dutch webshop), so I could send my phone to a repaircentre wicht they have a contract with. Maybe the place where you bought it offers such a service?
I had the same problem on my qtek 8310!
The problem can be fixed if you got some electro spray!
If you spray some on your headset and take it in and out a few times, it should solve the problem
is that like compressed air?
I had the same issue with my 2125 when i first got it. It never thought I took the headset out. What worked to me was taking an uncoated paperclip, unfold it, and wiggle it around in the headphone jack until the PROFILE went from HEADSET back to NORMAL. May not be the case for you, but....
Exitao said:
is that like compressed air?
Click to expand...
Click to collapse
I think it's called "contact spray"
I also faced this problem, wiggling the the headset plug in the jack seemed to help, never ran into the problem again.
music on bluetooth headset handfree auricolare
the best of for end problem and... FREE
http://trianglepowers.com/PPC/ViewApp.aspx?ID=36
Very thank's all boy programmatore!
Lucasss
i found the solution.. here's how it goes
play some music, then take your jack, push it in, then start pulling it out slowly level by level, until u hear the sound playing from the speaker again, when you do, pull out the jack fast. that solved my problem, hope htis help others too.
hi i am having sound out put problems from the 3.5 mm jack and the speakers and the earpeices and my mic isnt working aswell.......?
does any one know wots goin on
please help
possibly your sound driver is messed up, or maybe the internal sound buses are damaged...
did you drop your Uni recently?
mzalan said:
possibly your sound driver is messed up, or maybe the internal sound buses are damaged...
did you drop your Uni recently?
Click to expand...
Click to collapse
either dropped it or....you pulled out the earphones jack quickly,,,,
try put the earphones back again....twist it left and right and pull it out while twisting it....
this solution did work when i had a problem not hearing anything from external speakers only from earphones....so...try it...MAYBE it will help,,,
HEY THATS IN CASE YOU DIDNT DROP IT....
dust/rust/humid prob.
Maybe you need to shower your whole Universal Motherboard & all hardware parts with WD40. Don't worry it does'nt hurts anything, & make sure you don't use any static current equipment to wash that WD40.
Don't clean WD40 with any cloth, cotton or any ear bud or anything else.
Just let it dry & absorb by itself for 2-3 hrs & then turn your unit ON.
Damaged 3.5 jack - Solved!!
Your 3.5 mm jack could be damaged, I do not why but it is a huge problem with the uni and with the s200, this problem happend to me and the solution was trying to reordenate the pines of the 3.5 jack.
You could see more tips in the s200 forum.
Hopes could help.
Saludos
Hi everybody
My Magician stopped giving me sound in the earpeace and in my bluetooth headphone but works when I turn on the speaker. Does enybody know what might have happened to it and if so how could I fix it?
Thanks
you didn't search the forum - did you ?
http://forum.xda-developers.com/showthread.php?p=977314
http://forum.xda-developers.com/showthread.php?t=252764
please let me know, if it helps...
Had the same problem 2 weeks ago.
After changing the earpiece, the problem still remained...
Well the problem is most likely one of the contacts of the black connector on the "Audio Daughter Board" (http://forum.xda-developers.com/attachment.php?attachmentid=29156&d=1152687263) which became loose during drop of the phone.
Look at the post #4 of http://forum.xda-developers.com/showthread.php?p=977314 to get more info.
I resoldered the contacts of the black connector thanks to the tutorial of bluehanul76 without beeing a specialist in soldering.
You just have to heaten the contacts with your soldering iron.
My magician works like on the first day thanks to this forum
Good luck with the repair!