wiuh,my services i-mate jam dead after upgrading.
i got in bootloader mode n upgrade radio rom to 1.12 use this rom NL_11300_131_11200.exe.
i deleted nk.nbf, and ms_.nbf, so just radio.nbf
upgrade success!
then i try to upgrade with the same rom(NL_11300_131_11200.exe) without radio.nbf. fail it say error id country.ok then i try the other rom.
JAM_WWE_11200_128_11210_ship.exe
i deleted just radio.nbf,because i just want to upgrade the rom.
at ext rom upgrade it success.but when maybe about 30% uprade rom,it fail. and say error.i forgot the error.
and my i-mate dead. :'(
if i put usb cable n open the back case(baterai still in side or not) the lamp red is on.
but when i closed the back case.it turned off.
nothing happen,no indicated the pda was still connected.activesync has no sound.usb on device manager didnt indicated there was a pda connection.
so??
what must i do now?
??? this is not mine.if mine i dont care too much,but this my costumers!
anyone can help pls!
i beg u.pls!
which model u r using, i have i-mate JAMA 101.
can u tell me how u enter to bootmode?
Sree...
sreejithachuthan said:
which model u r using, i have i-mate JAMA 101.
can u tell me how u enter to bootmode?
Sree...
Click to expand...
Click to collapse
same as u did.
"please help me, i have my i-mate JAMA 101, i need to install new OS.
but cant enter its boot load. i tried camera + power + reset button this also not working...pls help me."
did that your buttons work?
i mean u have checked the button 1 by 1.(camera it self,power,then reset button?)
did that still work?
if not make it sure.dissambler it.check all the button.i can say all of the models of all pda are the same way to hard reset (as long as i know)
i have flashed many of them.
learnig said:
wiuh,my services i-mate jam dead after upgrading.
i got in bootloader mode n upgrade radio rom to 1.12 use this rom NL_11300_131_11200.exe.
i deleted nk.nbf, and ms_.nbf, so just radio.nbf
upgrade success!
then i try to upgrade with the same rom(NL_11300_131_11200.exe) without radio.nbf. fail it say error id country.ok then i try the other rom.
JAM_WWE_11200_128_11210_ship.exe
i deleted just radio.nbf,because i just want to upgrade the rom.
at ext rom upgrade it success.but when maybe about 30% uprade rom,it fail. and say error.i forgot the error.
and my i-mate dead. :'(
if i put usb cable n open the back case(baterai still in side or not) the lamp red is on.
but when i closed the back case.it turned off.
nothing happen,no indicated the pda was still connected.activesync has no sound.usb on device manager didnt indicated there was a pda connection.
so??
what must i do now?
??? this is not mine.if mine i dont care too much,but this my costumers!
anyone can help pls!
i beg u.pls!
Click to expand...
Click to collapse
the problem has been solved.i flash it many times so the batterai was too low.in brick condition, batterai cant be charged.so i changed it with other batterai.its ok now.thx for the rom.
Related
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
araheels said:
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
Click to expand...
Click to collapse
Try flashing it with the last WWE (non-arabic) version available for download from i-mate site.
thanks bro, i did try to flash but its not connecting, becaz its not on, when i press power button it just blink and not turned on, i am so worried, flash is done when active sync is working and the jamin is turned on, its not on
Most likely the file corrupted.
I dont know how to put Prophet in bootloader mode but can be found in forums.
Try to put the device in bootloader mode; and try to flash afterwards.
Cheers
I have the same problem after flashing with a corrupt rom. Only if i connect the JAMin to the power supply and then press and hold continuously at the camera button and press the power button once the device go to the 'boot loader mode'. But this don't help me because i have no connecting to the PC over USB.
read the forum it's written how you can put it on boot loader mode or you can try to hard reset
I don't find this post .
I try the hard reset but they dont't help.
I don't come in the boot loader mode, only if i connect the device to the power supply it works but now i haven't a connecting to the PC.
If i not connected to the power suppley and press now and hold continuously at the camera button and press the power button once there is now boot loader i see only for one moment
a white screen and also for one moment the blue light in the speaker
can i do not install the rom from my sd-cart ???
have anybody the image from JAMin ??
I have the same problem
Did you find solution ?
Forget about power button.
Press camera button. While holding it use the stylus to softreset. Take the stylus out but hold the camera button pressed. In less than 5 seconds, you will enter bootloader screen.
Hope it works.
You must put your device on to bootloader mode, how? Press the camera and the coomon manager (at the same time) put your stylus into the whole (as you made a normal soft reset) put your stylus out of the device but not the camera and the common manager botton, just a couple seconds after.
Don't be affraid is your device creen become with three colors, is normal nad the typical signal is on to bootloader mode. Now is time to find a JAMin ROM in the club imate web (if you are a member) or here in a ftp.
Tell us if you can fixed the problem.
jamin no boot
dear freind
try to connect the power supply to the cabel to enter to the bootmode and try to do software (i have same problem after flashin the jamin by kjam rom )
SAME PROBLEM AFTER DOWNGRADE CAN SOME ONE POSTE NEW ROM FOR THE IMATE JAMIN
probleme solved who want to know how to solve problem pm me
Any idea?
Do you have the solution???
Thanks
hi im having the same problem can u please inform me how u solved it, as im loosing the bootloader screen when ever i unplug it from the power.
buying a cradle will do the job
Jamin flash error
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Try this
Take a look at this thread - I think you are having the same problem as PianoSam
http://forum.xda-developers.com/showthread.php?t=300356
lordlinus said:
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Click to expand...
Click to collapse
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
lordlinus said:
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
Click to expand...
Click to collapse
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
No
It's in the link - just download it from there!!!!!!
lordlinus said:
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
Click to expand...
Click to collapse
hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i tried to update my rom through boot loader mode but again failed
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
guys please give me Advice and solution for this g3 g4 Problem
i even tried sending my phone to service center but stupid people dont know how to solve it and they returned me back
Thanks in Advance
You have bricked your phone... You just can't install a G4 rom on a G3 phone... Different chipsets are the cause of the problem... Sorry
you mean to say its over ?????????????
there should be any way
You'll have to wait to see if Jesterz manages to produce a goldcard...
BTW a goldcard it's basicly a mem card with a rom in it that autoinstalls itself thus no need for the usb connection... This fits your case cause you don't have an active usb conection because of the driver/chip conflict...
wrong software
I have the same problem i tried to flash my g3 with jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 by mistake and it was ok until the end of process when i finich it with congratulations and bla bla my device stills in the bootloader mode all the time. I can now connect and start to flash but when it comes to 80% of the process it stops with error 360 wrong command. Pleas is there any help for some kind of downgrade flash or so because it can only get boootloader but never start with software. When I try with jesters RUU-Prophet-g3-AKU2.2-2.20-2.47.21-Jester-r1 the whole process finish ok but the phone stills in bootloader. The same thing is also with RUU-Prophet-g4-AKU2.2-2.20-2.47.21-Jester-r1 I can not execute step2
that's why you should read the "sticky" first before you do it.
I have a Dopod 818Pro from a friend of mine but in Chinese ROM, so I have to read a whole nite the sticky and found out what is my Dopod version, finally I found it is G3, so I did all the steps, from unlocked the CID till upgrade to Jester latest ROM for G3 and skip the G4.
please help
Yes i realy know that it was my fault and my big mistake so i vould not do it again but now i need help because it stills in bootloader i i can even start flashing the device that gives me hope that some kind of recovery is maybe possible.
Yes i also commited this mistake its my fault but i really need help my device still enters into bootloader mode.
ur problem
there is nothing to do anymore u have to wait u CANT DO ANYTHING ITS OVER
how do you mean it is over. Do you think that could not repair it. Is it possible with sd card or jesters gold card and how. Help me please if somebody knows
there must b some way to overcome this problem
jesterz's gold card isn't working yet, and for now it's only for G3...
My hardware is G3 but flashed by mistake with G4 and now is in bootloader mode so i can start flashing but i do not know with what and how. Could you please explain me how and where can i find and use goldcard for g3 if possible Thanks
have u tried holding the camera button while softreset and then flash rom again
Yes sure i tried to flash rom from jesters for g3 which is for my device instead jesterz g4 what i used by mistake and it passed ok but when i restart it stills in bootloader mode only, so i could flash but do not know which firmware should i use
i've the same symptomes as mjankovic and aarif_ziaee, (bricked my phone)
but the only things i think i've forgot, is to cid unlock my device before doing the step 2
i have a question.
i have the rom PDAMobiz_Prophet_WM5AKU3.3_v3301
(witch is not an auto installable tile, it's a folder containing exe, dll, bat and nb file)
is it possible to install it by using teraterm pro or mtty? (connected and install bats and cabs by thoses software)
ps : i'm sorry for my bad english, i'm french not going to my languages faculty since i'have bricked my phone. need to fix it soon !
help... i downloaded smart1's (normal, not clean) update, and launched UPGRADE_ROM.DAT from PC... it said initializing and everything... and then it reached to "copying something.dll' ... i waited 10 minutes or so then i got something like:
"error cant copy ....... because connection closed from remote... something like that."
i did NOT touch the imate during the process
and now when i turn on my imate i get the HTC with white background for a second but then it freezes on the blue "i-mate" screen... displaying:
IPL 2.13.0001
SPL 2.13.0001
GSM 02.20.21
OS 10.1.0.811
when i connect it to pc, windows does recognise and install my device but ActiveSync doesnt connect.
i tried removing the battery then putting it back in then pressing and holding the conn. button along with the power button and i DO get to the bootloader screen (with three colors) and then when i plug in the usb i get a small 'usb' word at the bottom of the screen, but still, ActiveSync doesnt connect... i tried installing the update again... but the program doesnt find my device
how can i make it work again ??? plz help me
thx in advance
Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD
johnnyduk said:
Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD
Click to expand...
Click to collapse
i read in another topic what u said above... thx for ur reply...
btw, i'm currently downloading a 56 mb file called:
JAMin_WWE_2130923_21309112_020720_ship.zip
it can be downloaded from:
ftp://ftp.clubimate.com/JAMin_WWE_2130923_21309112_020720_ship.zip
or (better direct link)
http://www.clubimate.com/support/JAMMIN/ROM/JAMin_WWE_2130923_21309112_020720_ship.zip
i suppose this is the file i shoudl install right now using bootleader mode ? right ?
my previous rom version was 2.13.9.23 (same as name of file)
so is this the file i shud be downloading right now ?
thx a lot in advance
Just BEWARE that the rom you download is for your phone, it will be for a G3 or a G4, if you get it wrong, your phone is DEAD.
Please read the wiki and stickies....................................
JD
please. my phone doesnt move. it stuck on login screen.:
any way to restore it? i tried to hard reset, soft reset...nothing..
i tried to install smart 1 and after this happened
Problem solved
Same problem for me, but I solved today:
I connected the phone to pc in bootloader mode, the pc see the phone and says ppc usb sync, but the activesync not started.
I tried to install a qtek official rom by dangaard (you can find it here: http://www.megaupload.com/it/?d=4ELWL078 ) and I solded the problem !
Thanks god!!!!
Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.
Twinsis said:
Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.
Click to expand...
Click to collapse
ftp://ftp.clubimate.com/JAMin_WWE_213923_2139123_022021_ship.zip
here is the official link for O2 xda or Imate Jamin
Same problem!
I had same problem but in my case with downgrade from WM6 to ASERG rom, i have downloaded RUU_Prophet_220734_2207114_024721_NVID.exe and that fixed my problem.
i have tired v3 wm6 update and..after the update my screen is stuck...at o2 sign..with bubbles,, the four red words appear on the screen but doesn't change anything...
i'd like to reflash back but it doesn't seem like connecting to PC via USB..
what do i do...?
and i found..
it just stopps in the boot loader mode and turns to black screeen .. and that's it...
I cna't even connect to USB so which means i can't flash back to normal..
is there any suggestions??
like resseting back up?
I have tried soft and hard reset but both don't seem to work.. still stuck in the bootloader mode....
What do I DO>>>>>>>>>>>>>....please help me...><
Try to Enter Bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
However, you have to write in the right post, i guess you mean the Ohlala_WWE_WM6_v3 ROM. If you had read the entire post youl'd know that this one is bad. V4 should solve the problem.
thanks for your answer !!but..
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
llvll said:
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
Click to expand...
Click to collapse
You cannot use "upgrade_rom.bat" to flash ur device with RGB screen. The bat file is for upgrade, not for fresh install. It means that you have to install AKU2.xx NVID.exe (executable) first. The .exe file can recognize ur device via RGB screen.
After reset ur device with AKU2.x and successfully connect to the PC vis Activesync, you then can run upgrade_rom.bat.
And... don't be too panic. You have to read more.
thank you so much !!
i' ll try it right now !! omg ...i'm so relived that I got an answer !!!
you are the best!
um...
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
llvll said:
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
Click to expand...
Click to collapse
here http://www.4shared.com/file/12240109/ca99469a/RUU_Prophet_220734_2207114_024721_NVID.html
thanks !!!
is there an o2 version of NVID??? anywhere? i've just installed this but it says Qteck..
No it's a Qteck ROM not an O², I don't know if there is a 2.20 NVID ROM from O² here, sorry.
i've just installed AKU...thing
after installing AKU...
my phone doesn't seem like it can connect to Antisync program..
is there any reason why..this is happpenin..?
make hard reset after flash firmware!
yese !!
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
you could try this. Someone else posted it here, and when my phone stopped connecting after some update it fixed activesync. It's a switch.
llvll said:
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
Click to expand...
Click to collapse
Had O2 ever released HTC Prophet?
Sorry but I'm not O2 fan.
I have only Prophet so I know only Prophet.
You could go to the right thread for ur device O2 and look for the right .exe file.
PS: is it XDA Neo? If it is Prophet it should be OK.
Try holding Camera+Comm buttons during pressing reset button ur device will ask u to Format something. Press send button (green phone button) and try again.
Safe
Thanks guys, you saved my S200
Matos
Ohyea !!
I found the solution !!! dat Qteck one worked but um....
yea and my phone is Xda Neo !!!
the black one !
thanks for all the replies guys !!!!!!!
Whoohoo, thanx for mentioning the bootloader mode (by only holding the camera button ) Now I can try another WM6 rom, which does work I hope
hello there same problem here.. mine is also xda neo.. when trying to upgrade wm6 it stuck exactly same as yours..how did u fix the problem? thanx for ur advice
I tried upgrading to a wm6 rom without knwoing i had to app unlock and supercid my phone... now its stuck on the 3 colour screen!! what can i do???
Reinstall rom again.
Flash original ROM
Flash the original ROM first and then after unlocking your Tornado, flash any ROM you want to upgrade to.
Follow the excellent Kar Hoe's guide to upgrade your Tornado and you will be fine.
you cant flash original rom when its stuck in the colored screen
Yes you can
wel im trying for more then a week now, but no go, no matter what i do or try.
It stays in bootloader 3 colour screen
Original flash file = no go, cause it cant connect to activesync.
mtty = no go , USB port can not open no matter what version of mtty.
ttermpro = no go , can not open.
So if its possible, please tell me how.
muiz2 said:
wel im trying for more then a week now, but no go, no matter what i do or try.
It stays in bootloader 3 colour screen
Original flash file = no go, cause it cant connect to activesync.
mtty = no go , USB port can not open no matter what version of mtty.
ttermpro = no go , can not open.
So if its possible, please tell me how.
Click to expand...
Click to collapse
turn off the phone and redo the ttrermpro steps
When i put the battery in, the phone goes on automaticly.
And goes in 3 colour mode.
And from there nothing works
muiz2 said:
When i put the battery in, the phone goes on automaticly.
And goes in 3 colour mode.
And from there nothing works
Click to expand...
Click to collapse
cause you dont have a operating system so to say so its going to go into the bootloader. if you get to a bootloader than your phone is not "bricked" or broken, you just need to flash a rom onto it.
follow this guide exactly http://karhoe.net/guide-upgrading-htc-tornado-to-windows-mobile-6
i have read that many times, and tried over and over again.
But it wont flash, no matter what i try.
i give up
You should flash with factory wm5 original rom.
Can you please tell me where to get that?
Simple, just google for SPV C600 WM5 AKU2 ROM
http://www.google.com.my/search?q=S...s=org.mozilla:en-US:official&client=firefox-a
http://www.orange.co.uk/business/download/c600_aku2/c600_email.exe
Try this
http://www.orange.co.uk/business/download/c600_aku2/c600_email.exe
Try this
Simple, just google for SPV C600 WM5 AKU2 ROM
http://www.google.com.my/search?q=S...s=org.mozilla:en-US:official&client=firefox-a
Double Posting
Talk about double posting
Can you tell exactly what procedure you are following so that we can troubleshoot?