So I've had my fuze a little over a year now, no major issues. Used mostly energyroms, but about December time I switched back to a simple non-bloated stock rom for the stability.
Anyway today at work I was texting, and I press the power button to put the phone in standby. And the screen remains on and usable. I tried again and it would not go into standby (power button physically feels normal, it does not feel loose or abnormal.) So i let it sit for a few minutes, then i look at it and a message poped up asking if i wanted to turn the phone off (like as if i was holding the power button)so i press no, then it comes up again a few seconds later and aagain and again. So I soft reset the phone.
The phone resets but takes a LOT longer at the att/htc splashscreen, then it hangs at the htc screen and does not make it to the wimo screen, but instead an error screen saying:
"The device is unable to boot because you have either turned off the device incorrectly or tried to install an applicationa from an untrusted source, press SEND to reset your device or press any other button to cancel..."
I think it went through the hard reset this time because when it restarted it asked to calibrate the screen and install stuff. it resets again sometime after that, still takes forever at the splash screen and comes back up to the error, only this time no matter what button i press it wont go away and boot into wimo. It seems like none of my buttons work (they wont light up now) when i slide out the keyboard, it is not lit up like normally.
And heres the kicker, my only way to turn on/off the phone is to take out/put in the battery. As soon as I pop the battery back in the fuze turns on. Is my phone toast? Ive tried to hard reset and the phone does not reach the bootloader, it goes straight to the splash screen. Same with trying to reflash it from my comp, raphealwrapper cannot find my phone.
I've only recently encountered the exact same problem on my Touch Pro, but stock ROM and everything. As far as I can tell, our power buttons are busted and probably need to be serviced. One of the contacts must be stuck in the 'on' position somewhere inside :\ As a temporary fix, I've been using AEButton Plus and remapped double tap end call key to turn the screen off, and removing the stylus to turn it on.
I have a Fido Razr HD (xt925) in Canada, running stock JB, not unlocked/rooted/anything, just the standard phone.
So I did a hard reset, on the suggestion of some to deal with the stuttering issues (which I found were quite bad). Now I have somewhat of a worse issue, it's stuck in an infinite loop of the android update logo (the green android with the spinning blue thing), then a black screen then the motorola logo. Occassionally it shows the android logo on it's bag with a red symbol with a ! in it (which I presume means it's corrupt). It's just repeating endlessly. After 20 minutes or so I tried a few things, plugging it into a PC, holding down the power/volume up/volume down buttons (which makes it go to a black screen while I'm holding them, but then it goes back to looping as soon as I release them), nothing works.
Any suggestions on what I can do or is this a return to the store because it's dead problem?
Just try Power + volume down for 10 seconds (simulates a battery pull.) Aside from that if you can get into stock recovery try wiping data and cache and then rebooting. If you can't, take it back.
champdood said:
I have a Fido Razr HD (xt925) in Canada, running stock JB, not unlocked/rooted/anything, just the standard phone.
So I did a hard reset, on the suggestion of some to deal with the stuttering issues (which I found were quite bad). Now I have somewhat of a worse issue, it's stuck in an infinite loop of the android update logo (the green android with the spinning blue thing), then a black screen then the motorola logo. Occassionally it shows the android logo on it's bag with a red symbol with a ! in it (which I presume means it's corrupt). It's just repeating endlessly. After 20 minutes or so I tried a few things, plugging it into a PC, holding down the power/volume up/volume down buttons (which makes it go to a black screen while I'm holding them, but then it goes back to looping as soon as I release them), nothing works.
Any suggestions on what I can do or is this a return to the store because it's dead problem?
Click to expand...
Click to collapse
Did you ever get it fixed? I had the same issue and eventually found a path to success. Let me know if not and I'll see if I can help!
zimzum57 said:
Did you ever get it fixed? I had the same issue and eventually found a path to success. Let me know if not and I'll see if I can help!
Click to expand...
Click to collapse
I wouldn't mind if you posted your path to success in case I run into the same problem at some point. My bootloader hasn't been unlocked as of yet. I'm holding out for a ROM that's really, really worth a proper flashing but am scared as hell about the issues people run into.. factory reset loops and failures, bootloader unlock loops now apparently. With the exception of Busybox, which has an uninstaller, I have everything symlinked into my /system directory from a folder in /data and it works great and makes everything easy to keep track of but there's always the doubt of the stray app that put a file there when I granted permission and I didn't know about it.
For my Razr HD, I found that holding volume up and down while the android logo did it's spinning until it ended got me to the recovery menu.. However this hasn't really fixed anything, every time I restart the phone it goes through the same process again and does a hard reset all over again. After a few seconds in the recovery menu it restarts the phone again and goes through a normal load process, but the phone is hard reset every time. It doesn't matter what option I select in the boot menu, it does the same thing (so I don't think it's detecting what option I select at all).
So back to Fido it goes.
Scratch the above post, someone posted a fix on the Fido forums that works perfectly, see thematrix49's post here - fido.ca/t5/forums/forumtopicpage/board-id/Smartphones/thread-id/8805
Same issue. Took me a while to figure it out through an amalgamation of various online helps. I repeated it several times to make sure it worked before I posted.
I was experiencing android logo with blue loading bar... after a few seconds it would stop and then quickly show the android symbol on its back with a red exclamation point logo. Then it would shut off.
- To restart, press and hold both power and volume down for approximately 10 seconds, then let go of the power.
(Should show Motorola logo, then go to green Android logo again)
- At Android Logo, immediately press the middle of the volume up/down rocker.... this should engage both buttons at once.
(I was able to initiate this with one press in the middle of the volume rocker... other times it took me a few quick presses)
(If done properly, the screen should stop and some yellow text will appear on the left side of the android logo.. let it continue, it may fail)
It should say:
Formatting /data....
Formatting /cache....
Data wipe failied.
Performing BP Masterclear...
This will bring up a blue text menu at the top. Use volume up/down to navigate. Power to select.
Go down to "wipe data/factory reset" and select by hitting power. Go down to "yes" and select by hitting power.
It should properly format the /data and /cache after about a minute. Once it completes it will bring the blue text menu back up. Select "reboot system now" by hitting the power button.
Voila.
Click to expand...
Click to collapse
Took a while to get the volume press to work, it's just a press, not a press and hold. I just kept tapping it over and over until it worked.
Guys can you post your build.prop and default.prop files? it needed to get fido fw with jb.
THANK YOU.......My Motorola xt925 went "Boot Loop" after i reset the settings. Neither Telstra or Motorola could help. Excellent work Champdood.......
champdood said:
Scratch the above post, someone posted a fix on the Fido forums that works perfectly, see thematrix49's post here - fido.ca/t5/forums/forumtopicpage/board-id/Smartphones/thread-id/8805
Took a while to get the volume press to work, it's just a press, not a press and hold. I just kept tapping it over and over until it worked.
Click to expand...
Click to collapse
You are a king among men. I was stuck on this issue for so so so so long. I was downloading roms and trying to flash them and god knows what else!
champdood said:
Scratch the above post, someone posted a fix on the Fido forums that works perfectly, see thematrix49's post here - fido.ca/t5/forums/forumtopicpage/board-id/Smartphones/thread-id/8805
Took a while to get the volume press to work, it's just a press, not a press and hold. I just kept tapping it over and over until it worked.
Click to expand...
Click to collapse
THANK YOU! You just saved me so much trouble and it was quite the worrisome situation I was in. Sidenote for anyone reading this after June 6, 2013. The link to that Fido forum may be dead but Champdood's instructions are the straight goods! :good:
Is there a permanent fix for this? I have to go through those fix steps every time I wipe my phone as it continues to go into loop...
FunkmasterC said:
Is there a permanent fix for this? I have to go through those fix steps every time I wipe my phone as it continues to go into loop...
Click to expand...
Click to collapse
Me too! I also noticed that the version that re-installed (the one time I did it) wasn't completely stable. It acted super weird adding an icon of one of my apps to the top left position of the screen one swipe over from the main/home screen every time I did a reboot.
At first I didn't even know what was happening only that my Google Now widget (which I usually keep in that space) was disappearing every time I rebooted and an icon was in the top left corner instead. Finally, I realized what was happening. Weirdest part of it all is that if the OS put an icon in there, on a reboot it would remain the same. But if I tried putting an icon there (or widget) on reboot it would be replaced.
Champdood saved my phone...
I would like to add that the same thing happened to me. I performed a factory reset from Settings > Privacy > Factory Reset and that just sent the phone into an endless loop of red logo > android logo > android logo on back > power off > repeat. Nice job Motorola.
On Motorola help pages it was all about Power button + Down and getting the white menu where you volume down to choose and volume up to select. That would successfully reset the phone but as soon as I powered down and up again: back in the infinite loop.
In desparation, I found this thread. Completely unique to hit the Power Up+Down simultaneous as a press not a hold when see the Android logo, indeed, brought up a blue screen, followed the instructions, successfully reset and so far, have been able to successfully power down and back up again. Will be bookmarking this page.
Thank you so much Champdood!
Alternative External Reset Instructions from Motorola themselves...
Hey, as mentioned Champdood's factory reset instructions work fine. Since reading this thread, I realized other's are having the same problem resetting using the menu (Settings > Privacy > Factory Reset), so I initiated a chat with Motorola about this. The person would not respond to my quizzing about the reason for this but did say it was called an Internal Reset and then named Champdood's method the External Reset. He also gave slightly different instructions for accessing the blue menu. I am reproducing both sets of instructions for you all here:
From Motorola Customer Service:
PERFORMING AN INTERNAL RESET:
From the home screen of your phone, touch Menu
Touch System settings
Scroll down and touch Privacy
Touch Factory Data Reset
Scroll down and check Erase internal storage if you would like to erase all the data on the phone internal storage such as applications, music, movies or photos.
Touch Reset Phone
PERFORMING AN EXTERNAL RESET:
WARNING: When using this feature; everything is deleted from the device.
NOTE: Reset will require a minimum battery level of 25%. If you are unable to perform a reset, please charge for 20-30 minutes and try reset again.
With the phone powered off, press the VOL UP + VOL DOWN KEY together + POWER KEY .
The device will display different BOOT OPTIONS
Use the VOL DOWN Key to SCROLL to Recovery and VOL UP Key to SELECT
Tip: If the device reboots, you may have waited to long to make a selection, you will need to begin the process again.
The device will display the Motorola logo and then the Android in distress ( logo with Exclamation mark)
Press and hold the VOL DOWN key for 5-10 seconds
While still holding the VOL DOWN key tap and release the VOL UP key.
The device will display additional menu options (Text will appear in BLUE)
Use the VOL DOWN Key to scroll to Wipe data / factory reset and the POWER Key to SELECT this option.
Use the VOL DOWN key again to select YES - delete all user data and press the POWER key to CONFIRM
Once the Formatting is complete, press the POWER key to confirm a REBOOT
The device will reboot and start the normal power up sequence .
Motorola Razor Issue Fixed
Your Tip really helped me fix my Motorola Razor HD phone.
Created my account only to write a thanks and to comment for the same.
Thanks
Another thanks.
My wife's phone was doing this after a Settings menu factory reset, but the instructions champdood posted worked.
I had to re-re-format the data and cache partitions about four times, but after that it worked!
And somehow root was preserved; SuperSU was missing, but I had root over adb.
Cheers champdood.
Perfect fix
champdood said:
Scratch the above post, someone posted a fix on the Fido forums that works perfectly, see thematrix49's post here - fido.ca/t5/forums/forumtopicpage/board-id/Smartphones/thread-id/8805
Took a while to get the volume press to work, it's just a press, not a press and hold. I just kept tapping it over and over until it worked.
Click to expand...
Click to collapse
Hey Champdood, THANKS! Your fix worked a treat - XT-925 now back on-line and loving it!!
Awesome, looks like the fixed worked on this POS Motorola I got here at work. Thanks.
my verizon xt 925 stucks at the loading screen logo, after it i had a low battery and it went off. Please help, my email is [email protected]
anthony
hello guys
i have the problem with my motorola xt925,
it refused to boot, uit only gets stuck at the loading screen logo (the red eye)
i tried hard reseting it but it does not show the android distress after i selected the recovery in the boot menu.
please help
Hi! So... I installed Magldr V1.13 many months ago and it has been very awesome. Yesterday, while sitting in class, my phone was in my pocket. (very rare occasion as I usually have it in a holster)
Anyhoo, it vibrated twice like it would for an email or text. I pushed the red (hangup) button to see the screen, and the screen stayed black but the buttons lit up. I repeated, same result. I took the battery out, turned back on and the phone stops loading after the "GO GO GO!". It just sits there.
I have taken the battery out and restarted it literally 12 times. I tried with and without SD card and Sim Card. I even tried holding in the yellow reset button. I don't know what else to do.
Any help is very much appreciated!
hope you find out the problem, I uesd to be in your situation, so sad
kimmy8705 said:
Hi! So... I installed Magldr V1.13 many months ago and it has been very awesome. Yesterday, while sitting in class, my phone was in my pocket. (very rare occasion as I usually have it in a holster)
Anyhoo, it vibrated twice like it would for an email or text. I pushed the red (hangup) button to see the screen, and the screen stayed black but the buttons lit up. I repeated, same result. I took the battery out, turned back on and the phone stops loading after the "GO GO GO!". It just sits there.
I have taken the battery out and restarted it literally 12 times. I tried with and without SD card and Sim Card. I even tried holding in the yellow reset button. I don't know what else to do.
Any help is very much appreciated!
Click to expand...
Click to collapse
Always it happens something like that out of nowhere. So I think the solution is only one. Factory Restart the phone and re-install everything from the begging. If you don't want to loose your stuff try to copy paste the stuff you got in your SD card.
L0rkh said:
Always it happens something like that out of nowhere. So I think the solution is only one. Factory Restart the phone and re-install everything from the begging. If you don't want to loose your stuff try to copy paste the stuff you got in your SD card.
Click to expand...
Click to collapse
I know right? This is the first time I have been without a phone this long since high school, lol. How can I factory reset it without being able to turn it on? I held down the volume down+home+power button and chose the wipe from that menu. It didn't do anything. I even held in the yellow button on the back, still nothing.
Ok. So I finally found a way to factory reset my phone even though I can't get it to really come on:
1. With your phone powered off, press and hold the VOLUME UP and VOLUME DOWN buttons.
2. While holding the volume buttons, press the END/POWER button briefly and then release it.
3. When you see a warning message on screen, release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the reset, or press any other button to cancel the reset.
Now, it's stuck on the "Stick Together" Tmobile logo
Hello. After bricking my device and getting it working again, I decided to factory set it. When it was booting, it came up with the yellow triangle. I can't seem to get out of it. PLEASE HELP. Thank you so much.
Edit to clarify: I wouldn't be so worried if this didn't happen while trying to reset my entire phone... Is there any way out of this? I can't seem to get into download mode.
Edit 2: It says SECURE FAIL: KERNEL at the screen and before the screen pops up, it says in the upper left hand corner in blue it says RECOVERY BOOTING...
Got it. Thank christ. Now Odin won't detect my phone.
Edit: I got it to work by holding volD+Home+Power. When the screen flashed the warning and is about to boot into the error, I pressed the volD button very fast until the warning for download mode came up.
EDIT: Surefire way to get into device: Make the screen go black if it isn't already by pressing the power button. After the screen goes black, hold down volDO+home for about two seconds and then, without releasing your fingers, start holding the power button. The download mode warning screen will flash briefly and then it will go off again. Once you see that screen flash, release your finger off of the power button. When the screen goes off, start holding the power button again. The next screen that loads should be the download mode warning. Instead of clicking "download mode" (unless that was your intent), click volDO to restart phone into regular mode.
Sorry, i am really new to this site, and never had a problem like this with a previous phone.
I get home from the grocery store and my phone is off, so it seems, plugged in it, got the M to pop up do the little world thing, then the screen goes to black,
i leave it to charge a little while, come back, and everthing on my phone is working , except for the actual display{now i know its not the display or screen because when i boot it there are no problems with the boot/restart} and if i touch around the screen it lightly vibrates, weird,
i put it to boot menu and my first time trying a normal restart nothing, so i go to motorolas website to get an application to back up my data or something get the motorola device manager and its useless, all it does is tell me my drivers are up to date, look around some more for an easy backup program can't find any except one that won't connect because i can't see where to press ok on the screen
just ended up copy pasting over all 5 gigs of hardrive space
i try to do factory reset, but if i click factory on the boot menu it just restarts it, if i go into recovery it pops up the picture of the opened android robot, and says no command, i have tried pressing volume up for 15 seconds, and then taping the power button to no avail,
interestingly enough once i managed to get the screen on for the phone then it faded to black like a screen saver never to come back.
Anyone know what i can do to unbrick the phone?a program that i can go in and restore it back to factory settings?
i recently updated to 5.0 maybe on friday, haven't had problems, or dropped phone since then
just extremely frustrating,
Recovery key combination was changed after lollipop. Press and hold power button for few seconds and then tap vol up (when you see android robot and no command)
Sent from my XT1033 using XDA Free mobile app
U can flash stock firmware also from your pc..press vol down + power button for fastbootmod then press vol down and then vol up and power button for recovery mod