Related
Hi everyone,
I think I may have bricked my Kaiser. I've been following some similar threads but nothing seems to be working to fix the problem.
I was going through the process to flash a new Rom, starting with installing HardSPL following this thread I was. I was having problems, I think because I have the 1.82 ROM version.
Finally, I thought I had HardSPL installed, so I continued to run KaiserCustomRUU.exe. This completed (jumped from 0% to 100%) very quickly. However, I reset my phone and it is now stuck in the tri-color bootloader screen
The screen has the says:
KAIS130
SPL-1.82.0000
CPLD-8
and has the letters RUUNBH in the top right corner.
I've tried removing the battery and resetting, but the phone always goes back to this screen. I've also tried running mtty, but without success. The command 'readconfig' returned a result 'Command error !!!'.
does anyone know of anything else I can try?
Small bit of good news: if I issue the command 'boot' using mtty, my phone boots into my original ROM successfully, with the mtty output:
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
It takes a long time to boot (like a couple of minutes), but it does eventually boots up fine. When I reset, I'm back at the tri-color screen though
If your at the tri-color screen, just reflash a new rom
Im not an expert but when its at the tri colour screen, try to flash Hard SPL again, it should pick it up and flash i believe.
If that goes through ok, then do the same to flash another ROM.
Again no expert at unbricking but its definately worth a try
japher said:
Small bit of good news: if I issue the command 'boot' using mtty, my phone boots into my original ROM successfully, with the mtty output:
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
It takes a long time to boot (like a couple of minutes), but it does eventually boots up fine. When I reset, I'm back at the tri-color screen though
Click to expand...
Click to collapse
Try this.
1.) Open ActiveSync and navigate to File > Connection Settings - Uncheck Allow USB connections.
2.) Download this ROM http://rapidshare.com/files/5781641...dio_sign_22.45.88.07_1.27.12.11_Ship.rar.html and flash it to your device.
That should work for you.
hi alltheway. thanks for the advice!
I don't want to sound ungrateful, but are you sure the above is safe? I just don't want to make a wrong step now and totally screw up the device (now that I can successfully do a manual boot using mtty).
I know you can't guarantee it but is this what others who are stuck in the bootloader have done?
japher said:
hi alltheway. thanks for the advice!
I don't want to sound ungrateful, but are you sure the above is safe? I just don't want to make a wrong step now and totally screw up the device (now that I can successfully do a manual boot using mtty).
I know you can't guarantee it but is this what others who are stuck in the bootloader have done?
Click to expand...
Click to collapse
I had this problem about 2 weeks ago.
I was flashing one of Dutty's Great ROMs and I lost power at the house and shut down my computer when I was 46% done.
I had the same RUUNBH in the top right hand corner. All I did to fix this was flash a factory shipped ROM like the one I provided to you and it worked great. No issue thus far.
Honestly I can't gurantee 100% if this will totally fix your problem but I am 95% sure.
Unless some other users have an answer for you I think this will be your best solution. Regardless of what you do you will have to flash to a new ROM anyways.
Also, I'm a bit dubious on whether i will be able to flash to that ROM. I don't think I have the right HardSPL installed to flash roms (see what my boot-loader screen says in the first post).
I'm no expert though.... obviously
Thanks for all the info alltheway. I'm too tired now (will probably f*ck the thing up even further! ), so I'll try flashing this tomorrow.
Here's some more info I've collected using mtty (my phone is an O2 XDA Stellar):
Code:
Cmd>info 2
HTCSO2___001¯JG±HTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK
HTCSKAIS1300O__0HTCE
New Thread
Read this:
http://forum.xda-developers.com/showthread.php?t=355910
Hi tqm. I've been following that post but as far as I can tell there is no solution there yet.
From what I can tell from that thread (and others), the only way stop the phone booting to the tri-color screen (in RUUNBH mode) is to flash with a ROM that matches the vendor. I think because I haven't been able to install HardSPL properly, my phone's version of SSPL will only load O2 ROMs (could be wrong here, but that's the picture I'm building ). Unfortunately no-one seems to have extracted the ROM from an XDA Stellar :\
I believe alltheway's solution above worked for him because he had HardSPL installed properly. He could load the stock ROM to fix the phone, because his SSPL version allowed different ROMs to be loaded. I'm not certain of this, and I'll probably try his suggested solution when I get home today... but I'm not too confident.
If only there was an mtty command to just get the phone out of 'RUUNBH' mode. I've seen the command 'task 8' mentioned on here, but it doesn't work when I try it. Does anyone know of a list of mtty commands for the Kaiser anywhere?
Definitely flash the original ROM, it will get your device to the default HTC shipped state.
Then sync phone with ActiveSync, install HardSPL again and then flash custom ROM.
I remember i had the same issue but the original rom is a lifesaver
You mean the original HTC ROM? or the original O2 ROM? (what my phone originally came with)
If I don't have one of the HardSPL versions posted on the forums (I believe they never installed properly, which is what caused all my problems I think), will I still be able to flash the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
Basically my questions is: is this stock HTC ROM flash-able to ALL kaisers? (even without downloading/installing HardSPL from the forums)
If not (i.e. I can't flash even the stock HTC ROM), is it expected that if I can't successfully install HardSPL, my Kaiser will only accept O2 ROMS?
japher said:
You mean the original HTC ROM? or the original O2 ROM? (what my phone originally came with)
If I don't have one of the HardSPL versions posted on the forums (I believe they never installed properly, which is what caused all my problems I think), will I still be able to flash the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
Basically my questions is: is this stock HTC ROM flash-able to ALL kaisers? (even without downloading/installing HardSPL from the forums)
If not (i.e. I can't flash even the stock HTC ROM), is it expected that if I can't successfully install HardSPL, my Kaiser will only accept O2 ROMS?
Click to expand...
Click to collapse
IMHO the HTC stock ROM should work even without HardSPL, at least for me it worked fine... but just for sure have your O2 stock ROM by hand.
jaso2005 said:
Im not an expert but when its at the tri colour screen, try to flash Hard SPL again, it should pick it up and flash i believe.
Click to expand...
Click to collapse
I don't thinks there's a way to flash HardSPL on tri-color scrren so far, coz activesync cannot connected to computer
the best way is trying to find the phone's offcial ship rom to flash
No luck trying to flash with the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
After getting to 1%, it reports an error:
Error [294] : Invalid Vender Id
As suspected, looks like this will only accept an O2 ROM Will have to wait until one is available.
Did you try installing HardSPL and then reflashing?
the stock HTC rom will not load onto your kaiser simply because it is still CID locked to O2's CID code. You HAVE to find the O2 rom that your device came with or any O2 ROM and reflash that and you will be good to go. You may also try and flash HardSPL but I dont think its going to work. But remember have a friend or someone on the forum dump and rebuild the O2 rom for you and just reflash the OS.nb or ROM only no radio!
It is very simple to dump and rebuild a rom so if you have a friend that has a kaiser have him over for an hour and dump his
thats your only shot at this point.
URPREY said:
Did you try installing HardSPL and then reflashing?
Click to expand...
Click to collapse
My current ROM version is 1.82. I don't think installing HardSPL has been solved for this ROM version, which I think is where all my problems started. I have tried, but no version of HardSPL (that I've found) will install correctly.
austinsnyc said:
You HAVE to find the O2 rom that your device came with or any O2 ROM... just reflash the OS.nb or ROM only no radio!
Click to expand...
Click to collapse
Thanks for the reply austinsnyc, this is what I'm hoping to do now, I'm watching this thread 'Has anyone dumped the o2 Stellar rom yet ?' closely Maybe I should reconstruct the ROM myself, I'm just a bit worried about arsing that up as well I'd rather someone experienced reconstructed and verified the ROM (on a phone that isn't already messed up).
Out of interest, would you be able to give me a succinct explanation of what is actually wrong with my phone at present? As far as I can tell, the only problem is that the boot-loader is stuck in RUUNBH mode. Has part of the ROM on the phone actually been destroyed?
I'm assuming right now that the point of flashing the O2 ROM is just to make the phone 'finish' a flash and get out of RUUNBH mode. Or is it actually to re-instate something that has been lost?
If it is to reinstate something that's at present lost, is this data definitely part of the os.nb?
If it's just to get the boot-loader out of RUUNBH mode, I'm REALLY gutted that there isn't just a mtty command to do this
Oh yeah, and perceptivepixel.com Ace!
I've always fancied flashing my Kaiser (V1615) with a new ROM, but was always nervous because I wasn't sure of the process and didn't want to risk bricking the phone as well as all the effort needed to get everything back on it I needed. Well, a few days ago my old Kaiser met the floor and an untimely end. So I decided to take the risk and put a new ROM on it and decided on the latest Dutty WM6.1 ROM.
I read all about flashing on here and made as much sense of it as I could. Thing is, I'm very technical in general, but not very familiar with Windows Mobile or flashing. I found there was lots to read, but it was all written with an assumed level of knowledge and understanding of terminology. As a result I found it quite hard to understand. I took the plunge anyway and started, but things didn't work out as expected and I didn't understand why.
I'm not trying to be critical of all the work a lot of people have put into the documentation that is available online, it's just that when I originally approached this with zero flashing experience I found it difficult and confusing to understand. What I really needed was a concise and basic introduction to flashing. I've now been through the process and after re-reading the documentation it makes a lot more sense.
I worked out you need to run something called HardSPL before you could flash a new ROM. I'm still not sure what HardSPL does apart from CID unlock the device, but what does CID unlock mean?
I ran HardSPL v1 and it started ok, but then I ended up with a white screen. At this point I already wished I hadn't started, but no going back now. Is it known why some phones white screen? Turns out it's a common problem, so followed the instructions to recover. All was well again, but still with the original ROM.
I thought I'd be brave and stuck with it and this time tried JumpSPL1.56-KAIS instead of HardSPL as recommended on one of the tutorials. This went better and I ended up with the Tri-Color screen. I plugged my USB cable in and USB showed on screen.
Next step I thought was to flash a ROM onto the device. I ran the Dutty updater on my PC and all started ok, but when the update got to 18% I received a communication error. I tried to recover using the updater, but the same thing happened. At this point the phone wouldn't boot, so I was more than a little worried and wishing I hadn't started!
Found something that described several options for recovering from this problem. I decided to try and flash the device back to the original ROM from Vodafone. When I eventually found that ROM I ran JumpSPL again, got to the Tri-Color screen and ran the updater. This time the update completed successfully and the phone rebooted and was all working again.
I decided to leave the device as it was and started customising it myself. I'd still love to put a cooked ROM on there, especially if it helps with performance, but after the experience above I'm not very confident.
Can anyone tell me where or what went wrong? I'm going to get my old Kaiser repaired and want to try again on that phone.
My flashing routene (not ideal but it works for me)
1) run the first part of the Kaiser SIM/CID Unlocker & Changer
2) after device reboots, hold camera button and restart to check SPL
3) Flash rom/radio of choice
4) Follow HardSPL v3.07, v3.28, v3.29 and v3.56 by JockyW 's second guide "If you have problems with the above process, try this:" and flash my 3.XX SPL of choice.
Sam
Wow, I need a cuppa now
I'll go through 1 at a time... (and Sam has answered some questions already)
-CID unlock means that when the phone is loading a new device into the ROM the Carrier ID check is removed, each Mobile phone carrier has a different CID in thier OS ROMs. Unlocked means you can flash a OS ROM from any carrier or a cooked OS ROM from this site.
-The Jump SPL should only be used for replacing the SPL. Do not flash anything other than SPL's when at the Jump SPL (or SSPL). OS and Radio ROMs should be flashed from either in Windows Or By Manually Entering the Bootloaders. More info on SPL's is here: http://wiki.xda-developers.com/index.php?pagename=SPL Questions?
-Have a look at flashing from SD Card to avoid communication problems, http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash
-The most clear instructions can be found here: http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Hope this helps.
Dave
Thanks for the advice, but this is what I normally encounter when I read something on here, which is advice which no doubt makes perfect sense to the author or others experienced in flashing, but usually raises more questions than it answers in my head.
For example;
1) run the first part of the Kaiser SIM/CID Unlocker & Changer
Click to expand...
Click to collapse
What do you mean by the "first part"? The thread you've linked to doesnt really explain what I'm downloading and doing.
2) after device reboots, hold camera button and restart to check SPL
Click to expand...
Click to collapse
Ok. I get this assuming you mean the device will reboot automatically and I restart it to check the SPL version that gets shown on the boot screen, but why do I need to do this?
3) Flash rom/radio of choice
Click to expand...
Click to collapse
So at this point I can simply plug my device into my PC and run the ROM updater I've downloaded. Working out what rom/radio version to download is a minefield in its own right.
4) Follow HardSPL v3.07, v3.28, v3.29 and v3.56 by JockyW 's second guide "If you have problems with the above process, try this:" and flash my 3.XX SPL of choice.
Click to expand...
Click to collapse
I thought HardSPL needed to be run before I flashed? Also, why the different versions? Which one do I choose?
BTW, not trying to moan about everything, just posting my experiences to find out where I went wrong, but also highlight some issues hopefully other flashing newbies can relate to and authors of tutorials can draw some useful feedback from.
Only one question, do I need to CID Unlock before using Jump and HardSpl or, the Hardspl does the Supercid ?
I'm not referring about SIM since I don't care, for now
With WM6.1 - Oficiall HTC ROM
Thanks
Thanks for that one dave, on reflection i kinda missed the whole point of the thread, and as for the majority of the stuff you posted i didnt undertand that to begin with.
Also, DaveTME, if you are wanting to flash a custom rom to youre kaiser. from my experiance and from the number of times ive seen this happen. i advise against asking for reccomendations(sp?) (not saying you will but its worth saying) try a few roms out and decide from there.
Also another thing to note. if you flash to WM6.1 remember to use a 3.xx spl otherwise you'll encounter a few problems with youre device.
Sam
What do you mean by the "first part"? The thread you've linked to doesnt really explain what I'm downloading and doing.
Click to expand...
Click to collapse
download the Kaiser unlocker and run the first stage of it, the program is in the linked thread.
Ok. I get this assuming you mean the device will reboot automatically and I restart it to check the SPL version that gets shown on the boot screen, but why do I need to do this?
Click to expand...
Click to collapse
No, after the device reboots, youre given youre Rom, Protocol and Radio. if you hold the camera button and reset you'll get youre SPL displayed, youre looking for 1.01 olinex to be shown
So at this point I can simply plug my device into my PC and run the ROM updater I've downloaded. Working out what rom/radio version to download is a minefield in its own right.
Click to expand...
Click to collapse
1) Yes, just run the RUU with youre chosen rom and thats it
2) its not a minefield, just make a decision on what rom you like and flash it. theres nothing to stop you flashing another one.
I thought HardSPL needed to be run before I flashed? Also, why the different versions? Which one do I choose?
Reply With Quote
Click to expand...
Click to collapse
The 1.01 SPL will allow you to flash a cutom rom. following that you need a 3.xx SPL as they are designed for windows mobile 6.1. as for yure decision. i use 3.29, yet other users have had better sucess with 3.56. Most rom chefs will say which SPL they reccomend anyway with their rom.
-CID unlock means that when the phone is loading a new device into the ROM the Carrier ID check is removed, each Mobile phone carrier has a different CID in thier OS ROMs. Unlocked means you can flash a OS ROM from any carrier or a cooked OS ROM from this site.
Click to expand...
Click to collapse
Great. Thanks for that. Makes perfect sense now
-The Jump SPL should only be used for replacing the SPL. Do not flash anything other than SPL's when at the Jump SPL (or SSPL). OS and Radio ROMs should be flashed from either in Windows Or By Manually Entering the Bootloaders. More info on SPL's is here: http://wiki.xda-developers.com/index.php?pagename=SPL Questions?
Click to expand...
Click to collapse
Ok. I think you mean that the SPL is a component on the device? What is the difference between HardSPL and JumpSPL?
-Have a look at flashing from SD Card to avoid communication problems, http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash
-The most clear instructions can be found here: http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Hope this helps.
Dave
Click to expand...
Click to collapse
Thanks, will have a read
DaveTME said:
Ok. I think you mean that the SPL is a component on the device? What is the difference between HardSPL and JumpSPL?
Click to expand...
Click to collapse
Read the "SPL Questions" Wiki Page, it is all there and fairly clear.
Ta
Dave
Hello everyone!
I need complete ROM WM6 not just upgrade. The same way we install new operating system after formatting hard disk.
Due to so many trials (sometimes successful sometimes unsuccessful) of flashing hacked ROMs, I think so many files either got displaced, missed or corrupted. Due to which some testing results unwanted things.
If somehow, we succeed to get complete ROM not just upgrade we can assure ourself that phone is safe atleast in terms of testing.
Thanks everybody
Em, each ROM here is a complete OS. There is nothing that stays behind if you flash another ROM to your phone...
frauhottelmann said:
Em, each ROM here is a complete OS. There is nothing that stays behind if you flash another ROM to your phone...
Click to expand...
Click to collapse
Somewhat agree but I've a question just to clear my confusion because I'm facing lots of problems and I want to minimise all. Previously, I run uspl_116_jockyw.bat I never used rom update utility of USPL instead I run ROMupdateUtility of ROM. Somedays back I ran SD card flashing but unsuccessful due to that I flashed ROMupdate Utility of USPL first time and finally I succeeded to flash ROM. After that I noticed I never need to run USPL again.
Now my question if we're flashing complete ROM and we're making new installation not just upgrade then USPL nb files must be removed from vox. Am I correct? If not I'm sorry.
Thanks
No, the SPL, Radio, Spalsh Screen and the OS are all diffenrent parts. All unofficial ROMs here are just the OS. So if you only flash unofficial ROMs nothing will chnage the other parts. It's different with the official ROMs, which usually contain SPL and Radio too.
ragsAnurag said:
Somewhat agree but I've a question just to clear my confusion because I'm facing lots of problems and I want to minimise all. Previously, I run uspl_116_jockyw.bat I never used rom update utility of USPL instead I run ROMupdateUtility of ROM. Somedays back I ran SD card flashing but unsuccessful due to that I flashed ROMupdate Utility of USPL first time and finally I succeeded to flash ROM. After that I noticed I never need to run USPL again.
Now my question if we're flashing complete ROM and we're making new installation not just upgrade then USPL nb files must be removed from vox. Am I correct? If not I'm sorry.
Thanks
Click to expand...
Click to collapse
My understanding it that it's because USPL & ROM are stored on seperate Flash memory so Flashing USPL will not Remove your ROM and Flashing ROM will not remove the USPL.
Roland
Ok,
Do you feel flashing OS don't damage other parts or flashing other won't effect OS?
Hi to all. Is there anyone who can help me with HardSPL my snap which shows SPL 1.24. I would like to use some of the cooked roms. Cheers.
rocksford77 said:
Hi to all. Is there anyone who can help me with HardSPL my snap which shows SPL 1.24. I would like to use some of the cooked roms. Cheers.
Click to expand...
Click to collapse
Try ookba's roms, use Auto_1.19 worked for me... If it all goes wrong as we now have a shipped rom you can fall back to SD flash as in this post:
http://forum.xda-developers.com/showpost.php?p=4872255&postcount=78
ibanyard said:
Try ookba's roms, use Auto_1.19 worked for me... If it all goes wrong as we now have a shipped rom you can fall back to SD flash as in this post:
http://forum.xda-developers.com/showpost.php?p=4872255&postcount=78
Click to expand...
Click to collapse
No, it didn't work for me. I thought by now there will be a solid solution to this. Now we are stuck with stock roms as we cannot HardSPL our devices.
SPL 1.24 is hard to hack. Anyone got any solutions??????
rocksford77 said:
No, it didn't work for me. I thought by now there will be a solid solution to this. Now we are stuck with stock roms as we cannot HardSPL our devices.
SPL 1.24 is hard to hack. Anyone got any solutions??????
Click to expand...
Click to collapse
What didnt work?
I ran the Auto_1.19, (it prompted that device wasnt connected a couple of times, then got the prompt on the device to ask if an application should be run, selected yes (using left softkey), then had to use the trackball to select yes (the screen obscures some of the prompt), then screen went black and RUU began upgrade proces..
ibanyard said:
What didnt work?
I ran the Auto_1.19, (it prompted that device wasnt connected a couple of times, then got the prompt on the device to ask if an application should be run, selected yes (using left softkey), then had to use the trackball to select yes (the screen obscures some of the prompt), then screen went black and RUU began upgrade proces..
Click to expand...
Click to collapse
When I use Auto_1.19, i press the track ball on my device, I get an Error message and asks me to send the error to microsoft.
rocksford77 said:
When I use Auto_1.19, i press the track ball on my device, I get an Error message and asks me to send the error to microsoft.
Click to expand...
Click to collapse
Try with the older version if still fails might be worth a hard reset....
Anyone knows if HardSPL for SPL 1.24 is developed yet?
HArder SPL 1.24
Yeah anyone? I have a SNAP with SPL 1.24 running WINDOWS Mobile 6.5 but I cannot for the life of me get any of the JockyW SPL's to work 1.17 or 1.19. I hate these Bloody Telstra / HTC phones, there locking them down so tightly nowdays. Not even the SDA unlocker works.. it tells me the phone is unlockable
SNAP with 1.22 Telefonica
Hi ther,
I´m running with a SNAP from Telefonica with SPL 1.22 and WM6.1 which doesn´t let me install any of the ROMS here. Not even upgrade to 6.5 of original ROM from HTC. It says 294 invalid vender ID.
I have also tried aplication unlocker.. and nothing seems to work.
A few questions... has HardSPL 1.24 been released?
Any ideas to be able to flash a new rom onto this baby...
Thanks
OkiOKi.
I have MAPL110 with SPL-1.24.0000. Successfully flashed by hspl 1.17 and
this ROM - 3VOLUTION SERIES *][WM6.5 STD 21854][Build 3VO.2.50.112509.
succesfully flashed spl 1.25. used hard spl 1.19 through activesync. stuck on tmo load up page then used bootloader then flashed 11.25.09 rom from there.
all went well and my wife has a newish dash for $100
Hello everyone.
Yesterday I saw that there was a new update of my favourite rom EnergyRom. So today I downloaded it, installed it, everything went well. Until I restarted my Raphael ( raph300 btw). It kept stucking on the bootscreen.. even after I installed the rom again it still stucked at bootscreen. So I began trying to fix it with installing my hardSPL again, that didn't work either, still no further than my bootscreen.. after a while I decided to downgrade my spl to my stock-spl. that went well but still stuck on bootscreen. So I tried to install my stock-rom from my provider: (t-mobile netherlands). But then the Rom updater stuck at 0% and I received the well-known [262] error. Suddenly I saw that I stupidly accidentally installed the cdma version of EnergyRom instead of the one I needed: GSM. That explained why it wouldn't boot in the first place. Now I tried to install the olinex hardspl, but the updater stopped everytime with the 262 error. I connected my device to another computer with windows XP, but there I saw that the computer recognized it as a CDMA device.
I know it is a stupid mistake, but is there anybody who knows what I could try? I also tried to hard-reset it, but that wouldn't help either. Any help would SO be appreciated
try to search a tool called MTTY maybe it helps
lvxincad said:
try to search a tool called MTTY maybe it helps
Click to expand...
Click to collapse
Thanx, but how can I use this in combination with my problem?
As I remember 2 years ago,HardSPL is somehow depended on RadioROM. Maybe the ROM influenced the Radio with HardSPL,so try to reflash HardSPL again and Radio. Or it works absolutely not?
http://forums.techarena.in/hardware-peripherals/1161954.htm
http://forum.xda-developers.com/showthread.php?t=371154
http://htcwiki.wetpaint.com/page/RUU+Error+List
TomasNM said:
As I remember 2 years ago,HardSPL is somehow depended on RadioROM. Maybe the ROM influenced the Radio with HardSPL,so try to reflash HardSPL again and Radio. Or it works absolutely not?
http://forums.techarena.in/hardware-peripherals/1161954.htm
http://forum.xda-developers.com/showthread.php?t=371154
http://htcwiki.wetpaint.com/page/RUU+Error+List
Click to expand...
Click to collapse
No, I can't update any ROM. So now i'm stuck with my stock SPL, therefore I wanted to Hard SPL my device, but that didn't work and since then I haven't been able to update any ROM.. would flashing on a different PC help maybe? now I am on a Win7 Pc but maybe it will work in WinXP..
It is also not a bad idea to try different PC with XP to flash. I remember apx.1 month ago I tried to update HTC Trinity with WM6.5 ROM and it keeps failed with some errormessage(nowadays I can't remember which,but the syndroms was similar). Then I considered it as "bricked",until I tried another PC and everything wents correctly and the phone is in its productivity again. Yes,tfirst PC was company notebook with lot of safety kind of software(firewall,this,that,etc...) and the second one was my private laptop at home,just equipeed with regular antivirus software,all updates disabled(instead of AV).
Btw,what about trying to flash official ROM,while you are with stockSPL? Maybe it helps you to startup again the device and then HardSPL again afterwards...
TomasNM said:
Btw,what about trying to flash official ROM,while you are with stockSPL? Maybe it helps you to startup again the device and then HardSPL again afterwards...
Click to expand...
Click to collapse
yeah, that's what I thought too. I tried that also, also tried other custom roms btw before going to the stock rom. But with the stock rom it also stuck at 0% on the update
so, today I tried to flash my rom with two different computers: one with win7 and one with winXP. didn't work either.. I read the MTTY thread and after I installed the custom driver I was able to connect trough MTTY. But what commands should I use to clear the ROM and is there any way that I can update my rom via MTTY?
search MTTY on the forums the first link has all you need to clear the rom and flash via MTTY
I think you may be screwed. You should've asked for help before you started messing with the spl. I don't understand why you thought reverting to the stock spl would be a good approach; it may well be the end of your device. What you should have done is just flashed a stock rom-that would probably have restored your device. Re-flashing hard spl is kind of pointless. The only thing that can over-write hard spl is the special 'stock spl' that olinex put together. It's not entirely stock, and I am not sure that it can be over-written by hard spl. The sole purpose of the 'return to stock spl' is so that you can flash a stock rom, then restore the spl so that you can return your device for warranty/service without being dinged for having unofficial firmware on the device. When you do this, you aren't anticipating getting the device back, so I'm not sure that hard spl can over-write it. I know there have been discussions on whether or not it can be over-written, but I'm not sure that there was ever a clear answer. Anyway, with the 'stock spl' on the device, you can't flash any cooked roms to the device. If you are very lucky, you may be able to flash a stock rom. So, my advice is to try a few stock roms.
I'm pretty sure you'll need hard spl to run mtty/task 29, so I wouldn't waste your time on that. I really doubt it works, and I'm not sure what it's going to buy you, anyway. You really need to be able to flash a rom to the device, and you can't flash a cooked rom with that spl. Maybe you can flash a stock rom, but maybe not. I'm not sure which carrier it will let you upgrade to, either.
NeoTokyo22 said:
search MTTY on the forums the first link has all you need to clear the rom and flash via MTTY
Click to expand...
Click to collapse
yes I did, but the problem is that I can't access my Internal Storage, so I can't put any ROM's on that. Tonight I tried to flash a ROM via my SD card, but when I put my device in bootloader-mode it kept saying that it was 'loading...'
If the bootloader just says 'loading', then you probably need to either reformat the card to FAT32 or rename the image to RAPHIMG.nbh. Make sure you get the extension correct (not RAPHIMG.nbh.nbh).
But you're not going to flash anything with the stock spl, anyway. You need hard spl. I'm not sure you can even flash a stock rom off of the sd card-it probably needs to do it over usb.
I updated lot of smartphones already,but it was already few years ago. However I think,that SP's are flashed with MTTY. For that I needed ROM image in nbh file and with some commands you tell the PC,that it should flash it. Don't forget to disable USB connection in Activesync on XP in case MTTY will connect.
TomasNM said:
I updated lot of smartphones already,but it was already few years ago. However I think,that SP's are flashed with MTTY. For that I needed ROM image in nbh file and with some commands you tell the PC,that it should flash it. Don't forget to disable USB connection in Activesync on XP in case MTTY will connect.
Click to expand...
Click to collapse
I already managed to connect my device with MTTY, the only thing I need to know is which commands I can use to flash the ROM through MTTY. It just sucks that I am not able to go to my Internal Storage, otherwise it would be much simpler I think.
Farmer Ted said:
I think you may be screwed. You should've asked for help before you started messing with the spl. I don't understand why you thought reverting to the stock spl would be a good approach; it may well be the end of your device. What you should have done is just flashed a stock rom-that would probably have restored your device. Re-flashing hard spl is kind of pointless. The only thing that can over-write hard spl is the special 'stock spl' that olinex put together. It's not entirely stock, and I am not sure that it can be over-written by hard spl. The sole purpose of the 'return to stock spl' is so that you can flash a stock rom, then restore the spl so that you can return your device for warranty/service without being dinged for having unofficial firmware on the device. When you do this, you aren't anticipating getting the device back, so I'm not sure that hard spl can over-write it. I know there have been discussions on whether or not it can be over-written, but I'm not sure that there was ever a clear answer. Anyway, with the 'stock spl' on the device, you can't flash any cooked roms to the device. If you are very lucky, you may be able to flash a stock rom. So, my advice is to try a few stock roms.
I'm pretty sure you'll need hard spl to run mtty/task 29, so I wouldn't waste your time on that. I really doubt it works, and I'm not sure what it's going to buy you, anyway. You really need to be able to flash a rom to the device, and you can't flash a cooked rom with that spl. Maybe you can flash a stock rom, but maybe not. I'm not sure which carrier it will let you upgrade to, either.
Click to expand...
Click to collapse
Oke, thanx for your input. I tried to reset my ROM memory with mtty/task 29, but that didn't work, just like you predicted. So my next question is: 'Is there any app that can perform the task 29 without MTTY?'. I googled it, but I could only find the task 29 app for the HTC HD2.. And further, does anybody have a recovery ROM for my RAPH300? I tried the stock ROM on the XDA thread of HTC Raphael, but still got the 262 error
There's really no point in doing Task 29. The bad rom isn't what's killing you now, it's the SPL. It's going to block task 29, no matter what you try (that's one of it's jobs). You should just try to get hard spl back on the device, or try flashing every stock rom you can find. I tend to doubt that either will work, though. The only other option would be to look up the jump spl developed by PoF. I don't remember the name (search for threads started by him), but it was a universal soft spl that would temporarily CID unlock devices so you could flash custom roms. I've never used it before, and I don't know how it loads. You may not be able to load it onto your device with its current state, and it may not even be compatible with a Raphael (it's 3 or so years old), but it's probably worth at least checking out.
Edit: here's the jump spl link. I think you may have to activate it off the device.