Hi everyone,
I think I may have bricked my Kaiser. I've been following some similar threads but nothing seems to be working to fix the problem.
I was going through the process to flash a new Rom, starting with installing HardSPL following this thread I was. I was having problems, I think because I have the 1.82 ROM version.
Finally, I thought I had HardSPL installed, so I continued to run KaiserCustomRUU.exe. This completed (jumped from 0% to 100%) very quickly. However, I reset my phone and it is now stuck in the tri-color bootloader screen
The screen has the says:
KAIS130
SPL-1.82.0000
CPLD-8
and has the letters RUUNBH in the top right corner.
I've tried removing the battery and resetting, but the phone always goes back to this screen. I've also tried running mtty, but without success. The command 'readconfig' returned a result 'Command error !!!'.
does anyone know of anything else I can try?
Small bit of good news: if I issue the command 'boot' using mtty, my phone boots into my original ROM successfully, with the mtty output:
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
It takes a long time to boot (like a couple of minutes), but it does eventually boots up fine. When I reset, I'm back at the tri-color screen though
If your at the tri-color screen, just reflash a new rom
Im not an expert but when its at the tri colour screen, try to flash Hard SPL again, it should pick it up and flash i believe.
If that goes through ok, then do the same to flash another ROM.
Again no expert at unbricking but its definately worth a try
japher said:
Small bit of good news: if I issue the command 'boot' using mtty, my phone boots into my original ROM successfully, with the mtty output:
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
It takes a long time to boot (like a couple of minutes), but it does eventually boots up fine. When I reset, I'm back at the tri-color screen though
Click to expand...
Click to collapse
Try this.
1.) Open ActiveSync and navigate to File > Connection Settings - Uncheck Allow USB connections.
2.) Download this ROM http://rapidshare.com/files/5781641...dio_sign_22.45.88.07_1.27.12.11_Ship.rar.html and flash it to your device.
That should work for you.
hi alltheway. thanks for the advice!
I don't want to sound ungrateful, but are you sure the above is safe? I just don't want to make a wrong step now and totally screw up the device (now that I can successfully do a manual boot using mtty).
I know you can't guarantee it but is this what others who are stuck in the bootloader have done?
japher said:
hi alltheway. thanks for the advice!
I don't want to sound ungrateful, but are you sure the above is safe? I just don't want to make a wrong step now and totally screw up the device (now that I can successfully do a manual boot using mtty).
I know you can't guarantee it but is this what others who are stuck in the bootloader have done?
Click to expand...
Click to collapse
I had this problem about 2 weeks ago.
I was flashing one of Dutty's Great ROMs and I lost power at the house and shut down my computer when I was 46% done.
I had the same RUUNBH in the top right hand corner. All I did to fix this was flash a factory shipped ROM like the one I provided to you and it worked great. No issue thus far.
Honestly I can't gurantee 100% if this will totally fix your problem but I am 95% sure.
Unless some other users have an answer for you I think this will be your best solution. Regardless of what you do you will have to flash to a new ROM anyways.
Also, I'm a bit dubious on whether i will be able to flash to that ROM. I don't think I have the right HardSPL installed to flash roms (see what my boot-loader screen says in the first post).
I'm no expert though.... obviously
Thanks for all the info alltheway. I'm too tired now (will probably f*ck the thing up even further! ), so I'll try flashing this tomorrow.
Here's some more info I've collected using mtty (my phone is an O2 XDA Stellar):
Code:
Cmd>info 2
HTCSO2___001¯JG±HTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK
HTCSKAIS1300O__0HTCE
New Thread
Read this:
http://forum.xda-developers.com/showthread.php?t=355910
Hi tqm. I've been following that post but as far as I can tell there is no solution there yet.
From what I can tell from that thread (and others), the only way stop the phone booting to the tri-color screen (in RUUNBH mode) is to flash with a ROM that matches the vendor. I think because I haven't been able to install HardSPL properly, my phone's version of SSPL will only load O2 ROMs (could be wrong here, but that's the picture I'm building ). Unfortunately no-one seems to have extracted the ROM from an XDA Stellar :\
I believe alltheway's solution above worked for him because he had HardSPL installed properly. He could load the stock ROM to fix the phone, because his SSPL version allowed different ROMs to be loaded. I'm not certain of this, and I'll probably try his suggested solution when I get home today... but I'm not too confident.
If only there was an mtty command to just get the phone out of 'RUUNBH' mode. I've seen the command 'task 8' mentioned on here, but it doesn't work when I try it. Does anyone know of a list of mtty commands for the Kaiser anywhere?
Definitely flash the original ROM, it will get your device to the default HTC shipped state.
Then sync phone with ActiveSync, install HardSPL again and then flash custom ROM.
I remember i had the same issue but the original rom is a lifesaver
You mean the original HTC ROM? or the original O2 ROM? (what my phone originally came with)
If I don't have one of the HardSPL versions posted on the forums (I believe they never installed properly, which is what caused all my problems I think), will I still be able to flash the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
Basically my questions is: is this stock HTC ROM flash-able to ALL kaisers? (even without downloading/installing HardSPL from the forums)
If not (i.e. I can't flash even the stock HTC ROM), is it expected that if I can't successfully install HardSPL, my Kaiser will only accept O2 ROMS?
japher said:
You mean the original HTC ROM? or the original O2 ROM? (what my phone originally came with)
If I don't have one of the HardSPL versions posted on the forums (I believe they never installed properly, which is what caused all my problems I think), will I still be able to flash the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
Basically my questions is: is this stock HTC ROM flash-able to ALL kaisers? (even without downloading/installing HardSPL from the forums)
If not (i.e. I can't flash even the stock HTC ROM), is it expected that if I can't successfully install HardSPL, my Kaiser will only accept O2 ROMS?
Click to expand...
Click to collapse
IMHO the HTC stock ROM should work even without HardSPL, at least for me it worked fine... but just for sure have your O2 stock ROM by hand.
jaso2005 said:
Im not an expert but when its at the tri colour screen, try to flash Hard SPL again, it should pick it up and flash i believe.
Click to expand...
Click to collapse
I don't thinks there's a way to flash HardSPL on tri-color scrren so far, coz activesync cannot connected to computer
the best way is trying to find the phone's offcial ship rom to flash
No luck trying to flash with the stock HTC ROM:
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.exe
After getting to 1%, it reports an error:
Error [294] : Invalid Vender Id
As suspected, looks like this will only accept an O2 ROM Will have to wait until one is available.
Did you try installing HardSPL and then reflashing?
the stock HTC rom will not load onto your kaiser simply because it is still CID locked to O2's CID code. You HAVE to find the O2 rom that your device came with or any O2 ROM and reflash that and you will be good to go. You may also try and flash HardSPL but I dont think its going to work. But remember have a friend or someone on the forum dump and rebuild the O2 rom for you and just reflash the OS.nb or ROM only no radio!
It is very simple to dump and rebuild a rom so if you have a friend that has a kaiser have him over for an hour and dump his
thats your only shot at this point.
URPREY said:
Did you try installing HardSPL and then reflashing?
Click to expand...
Click to collapse
My current ROM version is 1.82. I don't think installing HardSPL has been solved for this ROM version, which I think is where all my problems started. I have tried, but no version of HardSPL (that I've found) will install correctly.
austinsnyc said:
You HAVE to find the O2 rom that your device came with or any O2 ROM... just reflash the OS.nb or ROM only no radio!
Click to expand...
Click to collapse
Thanks for the reply austinsnyc, this is what I'm hoping to do now, I'm watching this thread 'Has anyone dumped the o2 Stellar rom yet ?' closely Maybe I should reconstruct the ROM myself, I'm just a bit worried about arsing that up as well I'd rather someone experienced reconstructed and verified the ROM (on a phone that isn't already messed up).
Out of interest, would you be able to give me a succinct explanation of what is actually wrong with my phone at present? As far as I can tell, the only problem is that the boot-loader is stuck in RUUNBH mode. Has part of the ROM on the phone actually been destroyed?
I'm assuming right now that the point of flashing the O2 ROM is just to make the phone 'finish' a flash and get out of RUUNBH mode. Or is it actually to re-instate something that has been lost?
If it is to reinstate something that's at present lost, is this data definitely part of the os.nb?
If it's just to get the boot-loader out of RUUNBH mode, I'm REALLY gutted that there isn't just a mtty command to do this
Oh yeah, and perceptivepixel.com Ace!
Related
I have an unusual problem with my oem att tilt running SPL-1.56.0000 (according to the bootloader screen).
The ROM is somehow corrupted in that it will not boot past the giant ATT logo and coordinates (?) screen. I have been having some trouble with the device, but this is a new occurrence not related to anything I did. I have never reflashed the ROM, and because it is in a current hosed state I cannot run hardspl on the device.
I have tried reloading many of the "ATT OEM" ROMs I can find, but they all return "Invalid ID" error the ROM uploader I believe because the versions don't match.
Is there any way to reflash the ROM and bootloader on the device without having first run hardspl? Am I SOL?
Thanks
RK
Did you try going to tri-color first then flashing a stock tilt rom?
Dude, I have the same problem...
I bought the tilt 2 weeks when I was in a business travel in the US and came back to Argentina... I'm kind of screwed about the warranty 'cause I don't think I'll go again so soon to the US...
Is there anybody who can help us with this?
The very diference is that (At the ATT start up Logo screen) the bottom line says D 1.57.00.00 instead of D 1.56.00.00.
Tried everything... soft reset, hard reset... and so on...
The thing is that at some point I think I can get to the phone in some way since if I turn on the phone keeping pressed the camera button and enter in the rom loader screen I can get comm to the phone using mtty (As pof explained to do for "Un-brick" the phone (In the case you got a bad flashing) in this thread...
So, please If anybody have any idea it would be great!
I still have a little hope, because it's like there is some kind of communication between the phone and the computer...
Thanks in advance to any help.
A.
both of you...
Check my sticky thread for reverting back to the stock tilt ROM and SPL...
all you really need from there is the Stock ATT ROM... download it!
Put your phone in Bootloader (shouldn't be too difficult by the sounds of it)
Install the stock ATT ROM.
If this doesn't work try extracting the downloaded ROM (using WinRAR or similar) then just run the ROMUpdateUtility.exe
Then you might want to consider installing HardSPL... the default download should work for the 1.56 guy. The 1.57 guy will need to download jwocky2001's whitescreen fix (check the stickies).
Good Luck!
I am at the tricolor screen and I have tried the instructions on your thread (thanks very much for making it so easy). However, it says invalid vendor ID after loading 1%; the device automatically reboots and reverts back to the ATT screen until I place it back into the tricolor bootloader again. I thought this was because the version I'm running is 1.56 and I could only find two original OEM ATT ROMs, neither was 1.56 and both failed.
BTW I couldn't do the part about hardspl and running the kaiser program on the device for obvious reasons, but I could get the kaiserruu program to recognize the device, another ROM and attempt to upload it.
Any other thoughts? Do I really need the exact same ATT OEM ROM as what is on the device or is something else wrong?
Thanks again
RK
Ok, so rapid short overview:
I tried to flash my O2 Stellar with the new HTC wm6.1 Kaiser ROM. The HTC website, for reasons unbeknowest to me would only give me the italian ROM, so I got the english variant off rapidshare.
Tried to flash, everything going well, until (at 0%) it turns around and says the ROM isn't compatible. I figure this requires some HardSPL goodness, but the installer for THAT jumps to 100% in seconds and doesn't seem to do much. Tried a soft SPL (SSPL-KAIS.. no white screen issue), hey-ho, presto! ROM tries to install.
...hangs at 15%, device reboots to the rainbow. Displays:
KAIS130
SPL-1.82.0000
CPLD-8
In the corner: RUUNBH
I've read ALL the other threads on this issue to try and restore the phone. I've tried ALL the O2 ROM dumps people have supplied (all two of them I could find) and every time it either had an error 262 (comms error) at 0%, or got as far as 1% or maybe 2% and then error 29-something (ROM not compatible/suitable for phone). O2 originals, cooked ROMs, HTC updated ROMs, ROMs for different vendors (those produced "wrong vendor" errors). NOTHING IS WORKING!! *tears out hair*
Apparently connecting with mtty and typing "boot" causes the device to try booting the original rom before the flash. I figure maybe I could boot it, copy the phone's OWN rom (c'mon, THAT rom would HAVE to work, right?!) and reflash it. So I fire up mtty, tell it to boot. But it doesn't. Instead, the screen sort of.. fades, between the SPL and pure white (looks almost like display is broken!) and mtty displays:
...OH. Ok, just tried again to copy mtty text and now it's booting.
This is what mtty displays as the phone boots:
Cmd>boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
Click to expand...
Click to collapse
Ok, focus of the thread changing, does anyone know if I could dump the ROM and flash it? I'm about to find out anyway but if someone knows this is foolish please let me know
Cheers, everyone.
Not looking good for you.
Sounds like you flashed a ROM into the SPL at a guess. You shouldn't flash anything except SPL's when you are in Soft SPL's (SSPL or JumpSPL).
Try PM'ing a guy called GSLEON3. He's a mod here and for a beer or two will probably set you right.
@GSLEON3, I really should figure some of this out someday myself. That way I can help rather than just pointing users to you.
EDIT:
You have tried the stuff in here first? http://forum.xda-developers.com/showthread.php?t=371154
Ta
Dave
DaveShaw said:
Sounds like you flashed a ROM into the SPL at a guess. You shouldn't flash anything except SPL's when you are in Soft SPL's (SSPL or JumpSPL).
Click to expand...
Click to collapse
In retrospect that's exactly what I did, yeah. Luckily the boot command worked on the fourth try (as above... guess perseverance gets results) and the phone worked enough for me to retry the HardSPL install (which worked). Then I was able to flash the O2 Stellar ROM found elsewhere in this forum which allowed the phone to boot normally again. THEN I was able to flash the english HTC Kaiser 6.1 WWE ROM.
That thread linking to MTTY techniques for formatting may have come in very useful, I will remember that one!
Go and "security unlock" your device now. It makes it almost unbrickable.
There is a app called FrankenKaiser which can re-install your SPL if you decide to format it (not that you would want to under normal circumstances)
Ta
Dave
I've always fancied flashing my Kaiser (V1615) with a new ROM, but was always nervous because I wasn't sure of the process and didn't want to risk bricking the phone as well as all the effort needed to get everything back on it I needed. Well, a few days ago my old Kaiser met the floor and an untimely end. So I decided to take the risk and put a new ROM on it and decided on the latest Dutty WM6.1 ROM.
I read all about flashing on here and made as much sense of it as I could. Thing is, I'm very technical in general, but not very familiar with Windows Mobile or flashing. I found there was lots to read, but it was all written with an assumed level of knowledge and understanding of terminology. As a result I found it quite hard to understand. I took the plunge anyway and started, but things didn't work out as expected and I didn't understand why.
I'm not trying to be critical of all the work a lot of people have put into the documentation that is available online, it's just that when I originally approached this with zero flashing experience I found it difficult and confusing to understand. What I really needed was a concise and basic introduction to flashing. I've now been through the process and after re-reading the documentation it makes a lot more sense.
I worked out you need to run something called HardSPL before you could flash a new ROM. I'm still not sure what HardSPL does apart from CID unlock the device, but what does CID unlock mean?
I ran HardSPL v1 and it started ok, but then I ended up with a white screen. At this point I already wished I hadn't started, but no going back now. Is it known why some phones white screen? Turns out it's a common problem, so followed the instructions to recover. All was well again, but still with the original ROM.
I thought I'd be brave and stuck with it and this time tried JumpSPL1.56-KAIS instead of HardSPL as recommended on one of the tutorials. This went better and I ended up with the Tri-Color screen. I plugged my USB cable in and USB showed on screen.
Next step I thought was to flash a ROM onto the device. I ran the Dutty updater on my PC and all started ok, but when the update got to 18% I received a communication error. I tried to recover using the updater, but the same thing happened. At this point the phone wouldn't boot, so I was more than a little worried and wishing I hadn't started!
Found something that described several options for recovering from this problem. I decided to try and flash the device back to the original ROM from Vodafone. When I eventually found that ROM I ran JumpSPL again, got to the Tri-Color screen and ran the updater. This time the update completed successfully and the phone rebooted and was all working again.
I decided to leave the device as it was and started customising it myself. I'd still love to put a cooked ROM on there, especially if it helps with performance, but after the experience above I'm not very confident.
Can anyone tell me where or what went wrong? I'm going to get my old Kaiser repaired and want to try again on that phone.
My flashing routene (not ideal but it works for me)
1) run the first part of the Kaiser SIM/CID Unlocker & Changer
2) after device reboots, hold camera button and restart to check SPL
3) Flash rom/radio of choice
4) Follow HardSPL v3.07, v3.28, v3.29 and v3.56 by JockyW 's second guide "If you have problems with the above process, try this:" and flash my 3.XX SPL of choice.
Sam
Wow, I need a cuppa now
I'll go through 1 at a time... (and Sam has answered some questions already)
-CID unlock means that when the phone is loading a new device into the ROM the Carrier ID check is removed, each Mobile phone carrier has a different CID in thier OS ROMs. Unlocked means you can flash a OS ROM from any carrier or a cooked OS ROM from this site.
-The Jump SPL should only be used for replacing the SPL. Do not flash anything other than SPL's when at the Jump SPL (or SSPL). OS and Radio ROMs should be flashed from either in Windows Or By Manually Entering the Bootloaders. More info on SPL's is here: http://wiki.xda-developers.com/index.php?pagename=SPL Questions?
-Have a look at flashing from SD Card to avoid communication problems, http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash
-The most clear instructions can be found here: http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Hope this helps.
Dave
Thanks for the advice, but this is what I normally encounter when I read something on here, which is advice which no doubt makes perfect sense to the author or others experienced in flashing, but usually raises more questions than it answers in my head.
For example;
1) run the first part of the Kaiser SIM/CID Unlocker & Changer
Click to expand...
Click to collapse
What do you mean by the "first part"? The thread you've linked to doesnt really explain what I'm downloading and doing.
2) after device reboots, hold camera button and restart to check SPL
Click to expand...
Click to collapse
Ok. I get this assuming you mean the device will reboot automatically and I restart it to check the SPL version that gets shown on the boot screen, but why do I need to do this?
3) Flash rom/radio of choice
Click to expand...
Click to collapse
So at this point I can simply plug my device into my PC and run the ROM updater I've downloaded. Working out what rom/radio version to download is a minefield in its own right.
4) Follow HardSPL v3.07, v3.28, v3.29 and v3.56 by JockyW 's second guide "If you have problems with the above process, try this:" and flash my 3.XX SPL of choice.
Click to expand...
Click to collapse
I thought HardSPL needed to be run before I flashed? Also, why the different versions? Which one do I choose?
BTW, not trying to moan about everything, just posting my experiences to find out where I went wrong, but also highlight some issues hopefully other flashing newbies can relate to and authors of tutorials can draw some useful feedback from.
Only one question, do I need to CID Unlock before using Jump and HardSpl or, the Hardspl does the Supercid ?
I'm not referring about SIM since I don't care, for now
With WM6.1 - Oficiall HTC ROM
Thanks
Thanks for that one dave, on reflection i kinda missed the whole point of the thread, and as for the majority of the stuff you posted i didnt undertand that to begin with.
Also, DaveTME, if you are wanting to flash a custom rom to youre kaiser. from my experiance and from the number of times ive seen this happen. i advise against asking for reccomendations(sp?) (not saying you will but its worth saying) try a few roms out and decide from there.
Also another thing to note. if you flash to WM6.1 remember to use a 3.xx spl otherwise you'll encounter a few problems with youre device.
Sam
What do you mean by the "first part"? The thread you've linked to doesnt really explain what I'm downloading and doing.
Click to expand...
Click to collapse
download the Kaiser unlocker and run the first stage of it, the program is in the linked thread.
Ok. I get this assuming you mean the device will reboot automatically and I restart it to check the SPL version that gets shown on the boot screen, but why do I need to do this?
Click to expand...
Click to collapse
No, after the device reboots, youre given youre Rom, Protocol and Radio. if you hold the camera button and reset you'll get youre SPL displayed, youre looking for 1.01 olinex to be shown
So at this point I can simply plug my device into my PC and run the ROM updater I've downloaded. Working out what rom/radio version to download is a minefield in its own right.
Click to expand...
Click to collapse
1) Yes, just run the RUU with youre chosen rom and thats it
2) its not a minefield, just make a decision on what rom you like and flash it. theres nothing to stop you flashing another one.
I thought HardSPL needed to be run before I flashed? Also, why the different versions? Which one do I choose?
Reply With Quote
Click to expand...
Click to collapse
The 1.01 SPL will allow you to flash a cutom rom. following that you need a 3.xx SPL as they are designed for windows mobile 6.1. as for yure decision. i use 3.29, yet other users have had better sucess with 3.56. Most rom chefs will say which SPL they reccomend anyway with their rom.
-CID unlock means that when the phone is loading a new device into the ROM the Carrier ID check is removed, each Mobile phone carrier has a different CID in thier OS ROMs. Unlocked means you can flash a OS ROM from any carrier or a cooked OS ROM from this site.
Click to expand...
Click to collapse
Great. Thanks for that. Makes perfect sense now
-The Jump SPL should only be used for replacing the SPL. Do not flash anything other than SPL's when at the Jump SPL (or SSPL). OS and Radio ROMs should be flashed from either in Windows Or By Manually Entering the Bootloaders. More info on SPL's is here: http://wiki.xda-developers.com/index.php?pagename=SPL Questions?
Click to expand...
Click to collapse
Ok. I think you mean that the SPL is a component on the device? What is the difference between HardSPL and JumpSPL?
-Have a look at flashing from SD Card to avoid communication problems, http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash
-The most clear instructions can be found here: http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Hope this helps.
Dave
Click to expand...
Click to collapse
Thanks, will have a read
DaveTME said:
Ok. I think you mean that the SPL is a component on the device? What is the difference between HardSPL and JumpSPL?
Click to expand...
Click to collapse
Read the "SPL Questions" Wiki Page, it is all there and fairly clear.
Ta
Dave
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Did you use WM6.1 or WM6.0 to unlock the phone? Put in boot loader and flash orginal WM6.0 ROM as the other user suggested. You should be able to flash it if it is not a brick.
If it doesn't work you can use mtty to recover your phone, the needed information you'll find in the Kaiser Wiki.
Hope it helps
I just had this exact problem.
Use the EXE included in the tutorial to flash any windows 6.1 ROM from the bootloader via USB, and you will boot again.
HTCOmega said:
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Click to expand...
Click to collapse
I know. The crazy thing is that I've successfully flashed a G3 and a G4 Wizard and I still find this confusing.
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
When I reset the device normally I get:
R 1.27.12.11
G 22.45.88.07H
D 1.62.00.00
I didn't try to flash any other ROMS to unlock it. I just went with the hard SPL and then tried the Unlock tool. The phone is stock.
Thanx for the replys. I reflashed the original ROM and now it's working again. This is what I have now:
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
Now when I reset the device normally I get:
ROM version 1.62.502.0
Radio version 1.27.14.09
Protocal version is 22.45.88.07H
Device info:
Windows Mobil 6
CE OS 5.2.1622 (Build 18128.0.4.4)
Can I go strait to a SIM unlocker and then flash a new ROM?
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
A couple of things:
1) The Kaiser-Unlocker only works on 1.xx hardspl's, so you'll have to put one of those on first.
2) You do need to install the patched radio before you run it.
3) You'll need to flash a compatible radio afterward too, or else your device might not boot all the way.
4) Next time please post these questions in the thread for the unlocker you are using. It makes it much simpler for everyone.
stuff said:
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
Click to expand...
Click to collapse
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
So I guess I went wrong with flashing 3.56 first and not 1.1
Then I need to patch the radio
Run the unlocker
rinstall the radio
Then flash the ROM
Problem I have now is that I can't seem to go back down to a lower SPL version.
shawndh said:
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
Click to expand...
Click to collapse
You need to read the instructions carefully, and ask questions in that thread. All the experts in unlocking will be there to help you.
Hello everyone.
Yesterday I saw that there was a new update of my favourite rom EnergyRom. So today I downloaded it, installed it, everything went well. Until I restarted my Raphael ( raph300 btw). It kept stucking on the bootscreen.. even after I installed the rom again it still stucked at bootscreen. So I began trying to fix it with installing my hardSPL again, that didn't work either, still no further than my bootscreen.. after a while I decided to downgrade my spl to my stock-spl. that went well but still stuck on bootscreen. So I tried to install my stock-rom from my provider: (t-mobile netherlands). But then the Rom updater stuck at 0% and I received the well-known [262] error. Suddenly I saw that I stupidly accidentally installed the cdma version of EnergyRom instead of the one I needed: GSM. That explained why it wouldn't boot in the first place. Now I tried to install the olinex hardspl, but the updater stopped everytime with the 262 error. I connected my device to another computer with windows XP, but there I saw that the computer recognized it as a CDMA device.
I know it is a stupid mistake, but is there anybody who knows what I could try? I also tried to hard-reset it, but that wouldn't help either. Any help would SO be appreciated
try to search a tool called MTTY maybe it helps
lvxincad said:
try to search a tool called MTTY maybe it helps
Click to expand...
Click to collapse
Thanx, but how can I use this in combination with my problem?
As I remember 2 years ago,HardSPL is somehow depended on RadioROM. Maybe the ROM influenced the Radio with HardSPL,so try to reflash HardSPL again and Radio. Or it works absolutely not?
http://forums.techarena.in/hardware-peripherals/1161954.htm
http://forum.xda-developers.com/showthread.php?t=371154
http://htcwiki.wetpaint.com/page/RUU+Error+List
TomasNM said:
As I remember 2 years ago,HardSPL is somehow depended on RadioROM. Maybe the ROM influenced the Radio with HardSPL,so try to reflash HardSPL again and Radio. Or it works absolutely not?
http://forums.techarena.in/hardware-peripherals/1161954.htm
http://forum.xda-developers.com/showthread.php?t=371154
http://htcwiki.wetpaint.com/page/RUU+Error+List
Click to expand...
Click to collapse
No, I can't update any ROM. So now i'm stuck with my stock SPL, therefore I wanted to Hard SPL my device, but that didn't work and since then I haven't been able to update any ROM.. would flashing on a different PC help maybe? now I am on a Win7 Pc but maybe it will work in WinXP..
It is also not a bad idea to try different PC with XP to flash. I remember apx.1 month ago I tried to update HTC Trinity with WM6.5 ROM and it keeps failed with some errormessage(nowadays I can't remember which,but the syndroms was similar). Then I considered it as "bricked",until I tried another PC and everything wents correctly and the phone is in its productivity again. Yes,tfirst PC was company notebook with lot of safety kind of software(firewall,this,that,etc...) and the second one was my private laptop at home,just equipeed with regular antivirus software,all updates disabled(instead of AV).
Btw,what about trying to flash official ROM,while you are with stockSPL? Maybe it helps you to startup again the device and then HardSPL again afterwards...
TomasNM said:
Btw,what about trying to flash official ROM,while you are with stockSPL? Maybe it helps you to startup again the device and then HardSPL again afterwards...
Click to expand...
Click to collapse
yeah, that's what I thought too. I tried that also, also tried other custom roms btw before going to the stock rom. But with the stock rom it also stuck at 0% on the update
so, today I tried to flash my rom with two different computers: one with win7 and one with winXP. didn't work either.. I read the MTTY thread and after I installed the custom driver I was able to connect trough MTTY. But what commands should I use to clear the ROM and is there any way that I can update my rom via MTTY?
search MTTY on the forums the first link has all you need to clear the rom and flash via MTTY
I think you may be screwed. You should've asked for help before you started messing with the spl. I don't understand why you thought reverting to the stock spl would be a good approach; it may well be the end of your device. What you should have done is just flashed a stock rom-that would probably have restored your device. Re-flashing hard spl is kind of pointless. The only thing that can over-write hard spl is the special 'stock spl' that olinex put together. It's not entirely stock, and I am not sure that it can be over-written by hard spl. The sole purpose of the 'return to stock spl' is so that you can flash a stock rom, then restore the spl so that you can return your device for warranty/service without being dinged for having unofficial firmware on the device. When you do this, you aren't anticipating getting the device back, so I'm not sure that hard spl can over-write it. I know there have been discussions on whether or not it can be over-written, but I'm not sure that there was ever a clear answer. Anyway, with the 'stock spl' on the device, you can't flash any cooked roms to the device. If you are very lucky, you may be able to flash a stock rom. So, my advice is to try a few stock roms.
I'm pretty sure you'll need hard spl to run mtty/task 29, so I wouldn't waste your time on that. I really doubt it works, and I'm not sure what it's going to buy you, anyway. You really need to be able to flash a rom to the device, and you can't flash a cooked rom with that spl. Maybe you can flash a stock rom, but maybe not. I'm not sure which carrier it will let you upgrade to, either.
NeoTokyo22 said:
search MTTY on the forums the first link has all you need to clear the rom and flash via MTTY
Click to expand...
Click to collapse
yes I did, but the problem is that I can't access my Internal Storage, so I can't put any ROM's on that. Tonight I tried to flash a ROM via my SD card, but when I put my device in bootloader-mode it kept saying that it was 'loading...'
If the bootloader just says 'loading', then you probably need to either reformat the card to FAT32 or rename the image to RAPHIMG.nbh. Make sure you get the extension correct (not RAPHIMG.nbh.nbh).
But you're not going to flash anything with the stock spl, anyway. You need hard spl. I'm not sure you can even flash a stock rom off of the sd card-it probably needs to do it over usb.
I updated lot of smartphones already,but it was already few years ago. However I think,that SP's are flashed with MTTY. For that I needed ROM image in nbh file and with some commands you tell the PC,that it should flash it. Don't forget to disable USB connection in Activesync on XP in case MTTY will connect.
TomasNM said:
I updated lot of smartphones already,but it was already few years ago. However I think,that SP's are flashed with MTTY. For that I needed ROM image in nbh file and with some commands you tell the PC,that it should flash it. Don't forget to disable USB connection in Activesync on XP in case MTTY will connect.
Click to expand...
Click to collapse
I already managed to connect my device with MTTY, the only thing I need to know is which commands I can use to flash the ROM through MTTY. It just sucks that I am not able to go to my Internal Storage, otherwise it would be much simpler I think.
Farmer Ted said:
I think you may be screwed. You should've asked for help before you started messing with the spl. I don't understand why you thought reverting to the stock spl would be a good approach; it may well be the end of your device. What you should have done is just flashed a stock rom-that would probably have restored your device. Re-flashing hard spl is kind of pointless. The only thing that can over-write hard spl is the special 'stock spl' that olinex put together. It's not entirely stock, and I am not sure that it can be over-written by hard spl. The sole purpose of the 'return to stock spl' is so that you can flash a stock rom, then restore the spl so that you can return your device for warranty/service without being dinged for having unofficial firmware on the device. When you do this, you aren't anticipating getting the device back, so I'm not sure that hard spl can over-write it. I know there have been discussions on whether or not it can be over-written, but I'm not sure that there was ever a clear answer. Anyway, with the 'stock spl' on the device, you can't flash any cooked roms to the device. If you are very lucky, you may be able to flash a stock rom. So, my advice is to try a few stock roms.
I'm pretty sure you'll need hard spl to run mtty/task 29, so I wouldn't waste your time on that. I really doubt it works, and I'm not sure what it's going to buy you, anyway. You really need to be able to flash a rom to the device, and you can't flash a cooked rom with that spl. Maybe you can flash a stock rom, but maybe not. I'm not sure which carrier it will let you upgrade to, either.
Click to expand...
Click to collapse
Oke, thanx for your input. I tried to reset my ROM memory with mtty/task 29, but that didn't work, just like you predicted. So my next question is: 'Is there any app that can perform the task 29 without MTTY?'. I googled it, but I could only find the task 29 app for the HTC HD2.. And further, does anybody have a recovery ROM for my RAPH300? I tried the stock ROM on the XDA thread of HTC Raphael, but still got the 262 error
There's really no point in doing Task 29. The bad rom isn't what's killing you now, it's the SPL. It's going to block task 29, no matter what you try (that's one of it's jobs). You should just try to get hard spl back on the device, or try flashing every stock rom you can find. I tend to doubt that either will work, though. The only other option would be to look up the jump spl developed by PoF. I don't remember the name (search for threads started by him), but it was a universal soft spl that would temporarily CID unlock devices so you could flash custom roms. I've never used it before, and I don't know how it loads. You may not be able to load it onto your device with its current state, and it may not even be compatible with a Raphael (it's 3 or so years old), but it's probably worth at least checking out.
Edit: here's the jump spl link. I think you may have to activate it off the device.