Ok here goes. Be nice, I'm new...
I have a Stellar in front of me (or Kaiser, TyTynII etc) which has managed to get itself into Boot Loader. I'm usually pretty good at getting these out of it but this one has me stumped, and I'm hoping someone may be able to give me some suggestions, or confirm my suspicions that it is kaput.
It's in Serial mode at the moment, showing
KAIS130
SPL-1.82.0000
CPLD-8
on the top of the screen.
So I plugged it into the computer and it nicely popped into USB mode which then let me flash it, using the file: RUU_Kaiser_O2_UK_1.82.206.1_radio_sign_22.45.88.07_1.27.12.32_Ship
This appeared to take, started the process, splash screen loaded, windows mobile loaded OK and for all intents and purposes was back at the factory reset (which is what I wanted). HOWEVER.....when I performed a soft reset it went back into Boot Loader and I'm now back at square one.
Any ideas? I can't install any homebrew ROMs on this, it HAS to be the standard ROM for reasons I'm not at liberty to post here (don't worry nothing illegal is going on, suffice to say, I shouldn't really be here!)
I have at least 2 others that are doing similar as well and would like to get these fixed also. All help/comments gratefully received and I apologise again if this is covered somewhere else.
It seems you have not done any SPL hard flashing yet.
Did you really read the Flashing for Noob sticky ? It's there .. first you need to do hard SPL, SIM/CID Unlock, then only you can change your ROM to anything.
Please go back and re-read.
Sorry. Will this do anything bad to the device, only I've never done anything like that before, I've just run the ROM flash file. I've never had to do anything like you suggested before. It needs to be put back to factory as it is going to get allocated to someone - which means I then have to install a clone over the top of this.....sorry if I'm being thick. I did read the document you suggested but that resulted in me getting more confused.
If this is not the right place for me to be, please feel free to close this thread and I'll keep looking elsewhere. Cheers.
Hi,
First of all: what do you want to do? Read this to clarify your intention
Take your time, read through the WIKI first.
After that, if you still want to flash, go to the Noob sticky.
If you don't have the passion, I'd suggest just use the phone as from factory. Reading the Wiki still will give you insight and many good tips/tricks without flashing.
Edit to addI apologize.
After re-reading again, it seems that what you're trying to do is reviving the dead Kaiser. From the SPL version, it's not yet 6.1. You can check out here to see any other official ROM matches, which what you currently use seemed to be correct.
Mod, please merge this with Kaiser stuck at Bootloader thread ..
Good luck.
Edit 2
It seems that when you did a soft reset (by pushing at the small hole using stylus?), the other two buttons (camera + power) are still pressed (or due to hardware, kept being pressed), thus resulting in boot loader displayed again?
Well that's why I couldn't work out why I couldn't get the ROM to stay.....this has never happened before! So yes, I am trying to revive a seemingly busted Kaiser. The customer handed it to me in Boot Loader mode. Usually running the RUU fixes this and we can then go about rebuilding it. However in this case it really doesn't want the factory ROM but I need it to! I can quite easily get it into USB mode and flash it by running the .exe file on my desktop - but then that's about all I can do. I can't give it back to the customer as the next time he performs a soft reset or switches it off, it'll be back in Boot Loader...ARGH!
Oh, and apology accepted!
And another thing, I just tried running the exe file again and got as far as the screen alignment and the poxy thing just locked....cue soft reset and back to Boot Loader. Me not happy.
Edit: A quick check of the Hardware and all the buttons appear to be OK - nothing looks like it's stuck down
If you want to take the looooong road, perhaps you can do flashing Hard SPL, unlock SIM/CID and then flashing any other ROM/Radio. Once you get a stable working device, you can flash back the OEM using this method
I'm not sure if this custom RUU can help: http://forum.xda-developers.com/showthread.php?t=334890
I haven't tried that, so it's just an idea for now.
Thread closed.
If you are still having problems with the bootloader check out my sticky.
If you need help with the flashing process check out mskip's sticky.
Only create a new thread for new issues that have not been discussed before.
Good luck
Thanks
Dave
OK, I too skim read (I read a lotta threads ).
PDA-Princess
I've sent you a PM.
Dave
Related
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))
My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?
You need to read the "how to flash" sticky.
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Try another ROM.
Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse
Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.
No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?
Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.
I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!
STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet
Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.
If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...
Which one should I down load from Cingular? Even though I have a Tmobile phone?
what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader
As soon as I get home, I will post them.
Thanks
Ipl 1.01
Spl 3.08
Thanks
Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.
flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck
hey Guyz. I have a Tilt that a customer gave me that got bricked while trying to flash one of dutty's roms...Problem is that the genius didn't load up Hard SPL even tho he told me that he did...now He wants me to fix it...even tho he didn't follow my instructions and read the WiKi...I kno that on the Hermes it was able to be unbricked. Is the same for the Kaiser possible? I would greatly appreciate your help as my customers are loving the work you guyz do here in nyc..
Thanks in Advance!
Cristian
What is the current status of the phone?
Can you get into the bootloader at all?
If you can get to the bootloader you should be able to load the AT&T AKU v0.4.4 ROM (the unoffical upgraded AT&T ROM). Once you get that loaded you should flash HardSPL immediately.
Let me know how it goes...
Cheers.
I bricked my tilt when it was less than 24 hours old... I recovered it with a BETA of the ATT rom and THEN redoing the hardspl thingy - worked a treat.
Do a search for tolt bricked and you should find afew threads for it.
The rom is called something like RUU_Kaiser_ATT_WWE....._Internal.exe
It goes to the Tri-Color Screen but stays there..I'll go ahead and research it so I can find the original AT&T and load it up...It shows a lot..workin for at&t and being a member on xda...U guyz have no idea how ya make life easier for my tilt customers b/c at&t truly dropped the ball on the rom...and by offering alternatives..u make the user experience so much better...thanks!
HTCFAN0923 said:
It goes to the Tri-Color Screen but stays there..I'll go ahead and research it so I can find the original AT&T and load it up...It shows a lot..workin for at&t and being a member on xda...U guyz have no idea how ya make life easier for my tilt customers b/c at&t truly dropped the ball on the rom...and by offering alternatives..u make the user experience so much better...thanks!
Click to expand...
Click to collapse
If you are at the bootloader screen (Tri-Color) then the phone is not bricked. In the sticky at the top on how to revert back for warranty replacement, it has links for the various roms. Just flash an official AT&T rom on it and you should be good to go. Then do the HardSPL.
Cool that you work for AT&T and hang out here! If you have any other warranty returns, I can give you my address as I wouldn't mind having a backup or two...
BTW: The AT&T ROM for the Tilt is actually quite good in the big picture of things. At least the phone is usable (slower than it should be and less memory than it should have, but its still very usable and stable on the official rom). If you want to ***** about official roms, go back to the 8125 and its official rom. The while the device (at the time) was great, that rom made the phone almost worthless (super slow, battery problems, bad radio, dropped calls, freezing, etc). I can't tell you how many people that run custom roms on the Wizard just can't believe what that phone is actually capable of.
Ok, sorry, got off topic there...
does Hard-SPL needs to be flashed just once on a device or does it need to be installed every tome a new ROM is going to be Flashed onto it?
mfrazzz said:
If you are at the bootloader screen (Tri-Color) then the phone is not bricked. In the sticky at the top on how to revert back for warranty replacement, it has links for the various roms. Just flash an official AT&T rom on it and you should be good to go. Then do the HardSPL.
Cool that you work for AT&T and hang out here! If you have any other warranty returns, I can give you my address as I wouldn't mind having a backup or two...
Click to expand...
Click to collapse
For some reason, it's not being recognized by my Activesync. I got it to recognize it but now it sayz Error 294: Invalid Vendor ID...I'm using the RUU_Cingular_WWE Rom for the Kaiser...so I'm flabbergasted at this point...
Quick Silver said:
does Hard-SPL needs to be flashed just once on a device or does it need to be installed every tome a new ROM is going to be Flashed onto it?
Click to expand...
Click to collapse
Only once! Than you can flash as much as you like!
HTCFAN0923 said:
For some reason, it's not being recognized by my Activesync. I got it to recognize it but now it sayz Error 294: Invalid Vendor ID...I'm using the RUU_Cingular_WWE Rom for the Kaiser...so I'm flabbergasted at this point...
Click to expand...
Click to collapse
ActiveSync will not recognize your device when in BootLoader mode!
The Vendor ID error means the ROM cannot be loaded on the Tilt without HardSPL. You need an original Tilt ROM. (That's what I think about this)
HTCFAN0923 said:
It goes to the Tri-Color Screen but stays there..I'll go ahead and research it so I can find the original AT&T and load it up...It shows a lot..workin for at&t and being a member on xda...U guyz have no idea how ya make life easier for my tilt customers b/c at&t truly dropped the ball on the rom...and by offering alternatives..u make the user experience so much better...thanks!
Click to expand...
Click to collapse
Oddly enough the "Original" Tilt ROM will not install on a Tilt that does not already have HardSPL on it (to spell it out for you, the CID of the ROM does not match the Tilt's stock SPL). If you check the "reverting back" sticky you'll find all this info already, though it is deep in the thread.
The AKU v.0.4.4 ATT Beta ROM does have the correct CID and will flash on a stock Tilt. SO that is what you are forced to resort to at this point. Once you get the beta ROM installed you can (and probably should) install HardSPL.
After all that, if you decide you want to return or warranty the phone follow the "revert" thread to restore it to "stock" form.
Some additional notes on your problem...
ActiveSync will not connect in Bootloader mode (this is expected). You should see a device show up in Device Manager however, I can't recall the exact description however.
quick flash procedure:
put phone in bootloader
connect usb cable
install ROM
FYI, the problem may not be a bricked tilt... you could try Pof's fix which involves using MTTY.exe to boot the phone, depending on how your "customer" tried to flash it it may just need a kick in the pants to restore it. (search Pof's SSPL for the Kaiser thread for instructions, the thread was closed so you will have to look deep).
<climbing on my soapbox>
Lastly... your use of the word "customer" concerns me... are you charging people for the work you do to their phones? If so, do you donate to the people who make it possible? I'm probably just misunderstanding you, but if you're profiting from others work, perhaps you should contribute (especially if you're coming here to ask for help).
</climbing down>
Good Luck!
Cheers.
Customers as in I work for an AT&T corporate owned Retail location and they have bought Tilts from me. They kno my Tilt has been modded and they usually want to do the same. I don't charge them for doing mods to their Tilts. This still remains a community where we help each other and I cherish that. Greed has no place here.
as far as ur suggestions...It looks like I'm gonna be drunk @ 4am on XDA tonite...lol...
HTCFAN0923 said:
Customers as in I work for an AT&T corporate owned Retail location and they have bought Tilts from me. They kno my Tilt has been modded and they usually want to do the same. I don't charge them for doing mods to their Tilts. This still remains a community where we help each other and I cherish that. Greed has no place here.
Click to expand...
Click to collapse
That's cool... my misunderstanding then. Hopefully no hard feelings .
All in all it sounds like the guy wants a custom ROM so you should probably get the ATT Beta ROM and install that. And then install HardSPL.
Check Kyphur's second post in the thread below for the ROM you want.
http://forum.xda-developers.com/showthread.php?t=343198
Thanks for the info sycho...I'll get to it after work..
Good news! The AKU 0.33 worked! Thanks for ur help sycho!
how can i re-install the window? at tilt 8925
i have wm6.1
i want to reset it so the error message shud gone like Recover ?
@kaal,
It seems what you want to do is a HARD RESET. Please visit Kaiser Wiki and read through. You'll know your phone better that way.
@HTCFan & Sirsycho, Glad you both sort it out in the community spirit Cheers!
sirsycho said:
Oddly enough the "Original" Tilt ROM will not install on a Tilt that does not already have HardSPL on it (to spell it out for you, the CID of the ROM does not match the Tilt's stock SPL). If you check the "reverting back" sticky you'll find all this info already, though it is deep in the thread.
The AKU v.0.4.4 ATT Beta ROM does have the correct CID and will flash on a stock Tilt. SO that is what you are forced to resort to at this point. Once you get the beta ROM installed you can (and probably should) install HardSPL.
After all that, if you decide you want to return or warranty the phone follow the "revert" thread to restore it to "stock" form.
Some additional notes on your problem...
ActiveSync will not connect in Bootloader mode (this is expected). You should see a device show up in Device Manager however, I can't recall the exact description however.
quick flash procedure:
put phone in bootloader
connect usb cable
install ROM
FYI, the problem may not be a bricked tilt... you could try Pof's fix which involves using MTTY.exe to boot the phone, depending on how your "customer" tried to flash it it may just need a kick in the pants to restore it. (search Pof's SSPL for the Kaiser thread for instructions, the thread was closed so you will have to look deep).
<climbing on my soapbox>
Lastly... your use of the word "customer" concerns me... are you charging people for the work you do to their phones? If so, do you donate to the people who make it possible? I'm probably just misunderstanding you, but if you're profiting from others work, perhaps you should contribute (especially if you're coming here to ask for help).
</climbing down>
Good Luck!
Cheers.
Click to expand...
Click to collapse
Because of you folks and this thread, I have a working device as opposed to a paperweight...Thanks!!!
Hi,
Was changing the ROM on my Kaiser, using JUMPspl as I had got the white screen using Hardspl. During the upgrade got an error at about 18%, went through the recovery procedure only to get back to the Bootloader screen with the screen saying
SPL-1.93.0000
I think it should say something different here!
At the moment can only get the the tri-colour bootloader screen with usb at the bottom.
Please any help would be much appreaciated.
Thanks
If you are at the tri-color bootloader screen, reflash a ROM.
that's where the process starts at anyhow,the bootscreen.
But doesn't the SPL have to be either Hardspl or jumpSPL.
I have tried to do the rom update again but sticks on 0% and gives error 262
Alemaker said:
If you are at the tri-color bootloader screen, reflash a ROM.
that's where the process starts at anyhow,the bootscreen.
Click to expand...
Click to collapse
Not advisable if he has the default SPL still though which by the number appearing at the tri col screen it appears to be the case.
Try doing a hard reset and see if it boots into the original ROM then at least you will find out if it is bricked or not, however, i'm not sure it will work based on the fact you got part way through in the first place.
Hold down the keys directly next to the Send and End (green and Red) Hold in the stylus and keep them all held untill you get a screen telling you to press the green (send) key.
Tried the hard reset, takes me back into the bootloader. Any other ideas?
Hmm... ok then.... you are pretty much looking at a very expensive paperweight at this moment in time then.
Look at this thread...it "may" (i'm not promising anything but it may point you in the right direction) help you out. Let us know how it goes.
http://forum.xda-developers.com/showthread.php?t=361612&highlight=bricked
cmcmill01 said:
Hi,
Was changing the ROM on my Kaiser, using JUMPspl as I had got the white screen using Hardspl. During the upgrade got an error at about 18%, went through the recovery procedure only to get back to the Bootloader screen with the screen saying
SPL-1.93.0000
I think it should say something different here!
At the moment can only get the the tri-colour bootloader screen with usb at the bottom.
Please any help would be much appreaciated.
Thanks
Click to expand...
Click to collapse
Hate to joint the parade, but the exact same thing happened here - 18% now stuck at 1.93.0000
For anyone else reading this BEFORE flashing a new ROM please read, read and read again EVERYTHING related to flashing on this site, wikis and wherever else you can get info.
Another idea for you. Search around here for how to flash from an SD card that may solve the issue out for you. As previously noted though....READ READ READ and be 110% certain you understand what you are doing before you do anything.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=stuck+bootloader
details some info for a Wizard, should it be the same for a Kaiser?
Will Mtty get me any further?
MTTY will at least give you a USB connection to the device it is worth a shot given your current situation.
There is hope!
I did a clean reboot of my PC and disabled my antivirus (avast) and was able to sucessfully reflash the new 1.62 rom (released from ATT site today).
Thanks will try the new 1.62 rom.
What commands can you use with MTTY?
tried the At&t rom gives me an error on the vendor id. Will try a HTC rom
I have tried multiple roms and they all give me the same error Error 294:Invalid Vender ID
Any ideas
Am starting to get worried because if the misses finds out that I have bricked the new phone, I am up to my neck i it.
If you are stuck in boot loader & would like some help via MSN Messenger, please PM me or look for me on MSM messenger at [email protected]. I will be available to help later this evening or tomorrow morning.
I have most of the files to fix these issues & can use MSN fileshare folders to help you.
Good chance that you can be up again in a matter of minutes
cmcmill01 said:
I have tried multiple roms and they all give me the same error Error 294:Invalid Vender ID
Any ideas
Am starting to get worried because if the misses finds out that I have bricked the new phone, I am up to my neck i it.
Click to expand...
Click to collapse
Invalid Vendor I.D. is cuz it's locked.
Had the exact issue myself and found a ATT ROM that will boot. It saved me bigtime, so I saved it. It's in one of the posts on one of the threads but I have the actual ROM, it'll overide that lock.- PM me if ya need it.
Got the same solution, Holy S**t about to have a heart attack. Tried nearly ever ROM out there, it was the Asia one that got me going.
Lesson learned: make sure you Hardspl after jumpspl.
Thanks for all the help folks
Glad ya got it fixed. One quick question?
Is your original ROM ATT or HTC ?
It is a HTC ROM. Done My Hardspl and got Sleuth v3.0 on it already
Happy days
Hardspl wouldn't load, so I did the work around (white screen).
Follwed the instructions. All went well.
Burned Blackwoodv1 onto the phone. Phone rebooted.
Customization screen came up, asked if I wanted to run "removehiddenproxy" or something like that. I ran it...
Phone shut off.
Now I get the AT&T screen over and over and over.
The device never starts. No bootloader.
Any ideas, or do I send it back and hope for the best?
Um... Not more than a few pages back, was an answer- just the power key and camera key together got it to a boot loader Now I'm going to try to flash the radio.
Rats. After the radio flash and re-flash, same thing. Rats.
Flash a standard HTC rom, see if that works. Sounds like you have a bad rom & radio combo. I had the same problem with my Mogul once.
flash an OS not a radio
read the kaiser wiki, it helps
Closed, betcha
Yep, you answer lies within the threads (or google).
Sorry to do this to you but I have no choice.
Suggest going to one of these threads:
1) The thread on Hard SPL
2) The thread on Jump SPL
3) The thread on the specific Rom you are trying to use
4) The Kaiser Wiki.
As the title says, I seriously think I am just being stupid. But I have just spent the last 5 hours searching, trying, and just about anything I can. But I can't seem to get anything to work.
Now on to my situation:
I just got a new Tilt, it is not my first. My first one was when it first came out for AT&T. So it was still the WM6Pro and I SIM CID and HardSPL'd it. So I do know how to do this stuff. Just now with this new one, it must be a newer one, because it came with WM6.1 on it.
Here is what I know I have on it. Bootloader shows this.
KAIS1*0
SPL-3.56.0000
CPLD-8
And this is when the AT&T logo pops up.
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Now the first thing I am trying to do is HardSPL it.
I swear I have tried everything.
First thing I tried was the simple, Kaiser SIM/CID Unlocker & Changer , I start with the Flash-HardSPL and get to the Bootloader saying USB with the Rom updater showing the status bar. Then with the phone still in bootloader, I get Error [260] : Connection, The Update Utility cannot connect to your PDA. and so on.
So I exit that. Go on to the next try.HardSPL v3.07-3.56
All of them end up as the same result as the first. But I will explain what V3.28 as I have heard and read that that is one of the best ones to use.
Get to bootloader, Computer monitor shows status bar, and phone shows status bar. And I wait for it to do anything and then maybe a minute or two it gives me an error. Error [262] : Update Error, The ROM Update Utility has encountered communication errors during the update process. and so on for recovery.
I've also tried to do the HTC Kaiser Hard-SPLv1 - CID Unlock & Flash any ROM to your device (4 free)
When I start this one up it gets me to my screen being completely white. and I can not continue after that without taking the battery out and starting the phone again.
I have also tried other things that I just cant remember right now, cause I have been trying to do this for so many hours, and downloaded so many different things. So if you can and may help me, anything and everything will be appreciated beyond the gratitude I can give. Once again, I do know what I am doing, but I do not know what I am doing ARGHHH! lol.
I think you need JumpSPL1.56-KAIS, then hardspl , Im assuming this because you didnt say you did this step in your post.
Read post #2 here http://forum.xda-developers.com/showthread.php?t=396922
pretty sure you have to downgrade to 6.0. Its been a while though and i could be wrong. also try this you should always be security unlocked
http://forum.xda-developers.com/showthread.php?t=361236
sd73ta said:
pretty sure you have to downgrade to 6.0. Its been a while though and i could be wrong. also try this you should always be security unlocked
http://forum.xda-developers.com/showthread.php?t=361236
Click to expand...
Click to collapse
I tried that one, and for 2nd poster, I did try that also. Sorry for not listing. But I still appreciate the help guys.
I was also thinking I had to go back to 6.0 but I went 55 pages back on this section of the forum, and I still cant find it. I'm still looking, but it seems like a dead end to me. =/
there was a guy having this issue a while back, look in the white screen thread towards the end! I will see what I can find for you!
Right now I found a 6.0 ATT rom, so I got that to work, now I will try unlocking it, thank you guys, and thanks to this post (70+ pages back!) http://forum.xda-developers.com/showthread.php?t=326933
Edit 1 :
Alright I got it back down to 6.0, but yet I still cant do anything with HardSPL, CID, or Security. If anyone has any solutions I will listen! Even if its bashing my head against anything! LOL! Sucks!
downgrade I don't believe is necessary
sd73ta said:
pretty sure you have to downgrade to 6.0. Its been a while though and i could be wrong. also try this you should always be security unlocked
http://forum.xda-developers.com/showthread.php?t=361236[/quote
Nope, I didn't have to. My tilt came with 6.1. I had some problems, ended up switching to an XP laptop, was using Vista(prem. sp-whatever). It's too late here, but maybe tomorrow I can figure out what I did, but I think the main thing was using a windows XP pro machine - don't know if it needed to be pro, but that's what I had. Thereafter I've used the vista machine without problem. Good luck.
Click to expand...
Click to collapse
Meh, you need to use JumpSPL first. I've had this happen before, and JumpSPL cleared it right up for me.
I think Jocky has a few you can use. Check his HardSPL thread.
I first tried to use Vista, but then went back to my xp machine.
Edit :
I've tried to the JumpSPL but had major brain damage last night. trying it again with a fresh day. Will let you know.
Just got it, thanks guys. I apologize for just being completely brain dead. But I really am happy that you guys helped out. I finally got it flashed with the HardSPL It was really easy now. I just could not remember how to get to the file explorer. And the JumpSPL 1.56 worked. Thanks!
Yeah, well I can NEVER find anything via search here. Hell, to prove that point, I just typed "stupid" in the subject search line and found: NOTHING!!! I don't know what the deal is, but I've just pretty much given up searching this site.
Which leads to more reading than I'd typically care to do.
J
Munchys said:
Just got it, thanks guys. I apologize for just being completely brain dead. But I really am happy that you guys helped out. I finally got it flashed with the HardSPL It was really easy now. I just could not remember how to get to the file explorer. And the JumpSPL 1.56 worked. Thanks!
Click to expand...
Click to collapse
Glad to hear you got it fixed.
Awesome, fully got it unlocked and everything! Thanks for telling me what I might have missed and messed up on!