Database Info

HTc Vox dead?

Hi
I have had my vox for about a year now, and yesterday I updated the ROM, and installed SmartToolKit on it. I was then browsing my contacts, when the phone suddenly freezed. Then I pushed the "turn off button" on the top of the phone, but nothing happened. Then I had to remove the battery. When i put in the battery again the phone wouldn't turn on anymore, and it still wont. I have tried to hard reset it, but nothing happens. When I try to turn on the phone, the LED lights for about a second, and then it goes out. The display doesn't show anything, and the phone doesn't vibrate. I have tried to take out the memorycard and simcard, but it does not help. It can go to boot mode when i push and hold the camera button while pluggin in the USB cable. I have tried updating the ROM again ind boot mode. But that doesn't help. What is wrong, and what can I do?
Baryylos

Baryylos said:
Hi
I have had my vox for about a year now, and yesterday I updated the ROM, and installed SmartToolKit on it. I was then browsing my contacts, when the phone suddenly freezed. Then I pushed the "turn off button" on the top of the phone, but nothing happened. Then I had to remove the battery. When i put in the battery again the phone wouldn't turn on anymore, and it still wont. I have tried to hard reset it, but nothing happens. When I try to turn on the phone, the LED lights for about a second, and then it goes out. The display doesn't show anything, and the phone doesn't vibrate. I have tried to take out the memorycard and simcard, but it does not help. It can go to boot mode when i push and hold the camera button while pluggin in the USB cable. I have tried updating the ROM again ind boot mode. But that doesn't help. What is wrong, and what can I do?
Baryylos
Click to expand...
Click to collapse
Welcome
Have you tried reflashing another ROM?
And please READ the Wiki
Also check here: http://forum.xda-developers.com/forumdisplay.php?f=358

orb3000 said:
Welcome
Have you tried reflashing another ROM?
And please READ the Wiki
Also check here: http://forum.xda-developers.com/forumdisplay.php?f=358
Click to expand...
Click to collapse
Yes I have tried that. Still can't get it to work.. Do you know what I can do ?

Possible Corrupted flash?

Hey all,
I need some help. The other day my touch cruise was working fine, but I wasnt able to connect to the network, and I thought it was time to do a soft reset. After soft reset my phone has now stopped working. It is stuck on the screen that says:
POLA100
SPL-3.13.0000
CPLD-2
The screen has 4 color bars on it, in this order:
RED
GREEN
BLUE
WHITE (SERIAL OR USB)
Every time I reset the phone it quickly flashes the screen with a messege that I believe says "No Image Found"
Any ideas on how I can fix this?
Thanks for all your help guys in advance!
Matrixum

A quick update...
I have managed to get back into the phone. I plugged it into the usb, and of course it would not recognise it. However, after it was plugged in I held down the camera button, and the power button and pushed in the reset button, and vola the phone restarted back to normal. I have not lost the operating system or anything. I am not sure what will happen if I turn it off. So I plan on backing it all up and then trying to turn it off and on.
But if you have any answers to this problem please let me know as I am not sure what i have done.
Thanks again guys
Matrixum
Update:
Ok everytime I turn off my phone I go back to the tri color screen. The only way for me to get back into the phone is if I plug it into the USB and hold down the camera button and hit the soft reset. Any ideas?

I guess nobody has had this problem? I must be the first! Seriously.... Well I still have the problem, each time I shut off the phone and turn it back on it goes to the tri color screen. I have to do my combination of camera button and soft reset in order to get the phone to start properly. I dont loose any information, but the phone is now running very slugish at times.
Once again, any help would be great... Unless I am really the first one to run into this problem.
Thx,
Matrixum

Hmmm... I have no idea what could the problem be.
But I have some questions:
1. What OS is/was on your Polaris?
2. Have you managed to backup your data via ActiveSync or other means?
It looks to me like you're stuck somewhere in the upgrade process. But I'm not sure, just guessing.
I'd recommend flashing Polaris with official ROM.
Be aware that you'll lose all your data on device.

Bootloader "No Image File"

Hey guys
I woke up this morning because I got a message. Opened it and then replied. Went to shut the screen off but the backlight remained on. So I just did a soft reset. Now the bootloader comes up and says no Image file.
What do I do?

You could try download a custom splash screen, put it on your SD and start up in bootloader mode, and then flash the new boot/splash screen
Hope this fix your problem

i figured the "image file" its looking for was the ROM?

hehe ofcourse, sry for the post before, my head is a bit screwed... i have been working on getting win 7 and NBH Utility to work together the last 2-3 days xD.
well then reflash the rom using the same method... you have Hard-SPL right?
the latest NRG is working like a charm

Bowdowntozoltan said:
Hey guys
I woke up this morning because I got a message. Opened it and then replied. Went to shut the screen off but the backlight remained on. So I just did a soft reset. Now the bootloader comes up and says no Image file.
What do I do?
Click to expand...
Click to collapse
Were you accidentally pressing volume down when you soft reset? That's what it sounds like to me. Maybe vol. down is sticking, for whatever reason. Does another soft reset get you out of the bootloader? Somehow, I doubt that your rom just up and walked away.

no i don't think i was on volume down. and no soft or even hard reset will even work. the bootloader tri color screen pops up and flashes white real quick and says "no image file" and then goes back to the tri color screen.
so i to flash it via SD card correct?

Have you tried pulling the battery for a bit? I still wonder if you have a sticky vol down button. Replace the battery, then push power. If you're still in bootloader, then you can either flash off your card or through usb.

how do i flash it via USB? just plug it in and run the rom install?

reflashed a new rom. nothing. still sits in bootloader mode.

ok so what based on what i'm searching ive found a couple things. I pm'ed a guy, and saw something about jumpspl. But apparently this is an app that goes on the phone? because windows xp wont run it? theres not a lot out there on jumpspl so i dont have a clue. should I retry flashing hard spl?

Hold on; your sig now says you have a tilt. But you've flashed a raphael rom to it? Flash a stock rom to it with the proper spl. You should ask mskip what to do in his Kaiser-flashing thread. This does not sound good. Did the phone actually work with the wrong rom on it?

Man, from what I've read about Kaisers, they are very delicate phones. If you flashed a raphael radio to it, it's deader than Michael Jackson. Are you sure you don't have a fuze? You gotta own a fuze, and not a tilt.

its a fuze sorry i have no idea why it says tilt.

Not quite sure why, but the phone is working again...

My $ is on a stick vol down key, and I'm riding that horse to the bank!

scratch that, it broke again. how can i fix the stuck down key? is volume down and reset like wipe the device?

if the phone had the volume down key "stuck" then it would constantly turn down the volume would it not? its fine when i can acutally get the phone to boot, but i shut it off and started it back up and it did it again. i have a feeling it has something to do with the wall charger, because i reset it multiple times before i put it there, but once i charged and reset, it died.

Yeah, that's true. I say I think that's the problem because holding volume down and soft resetting sends you into the bootloader. If your sd card doesn't have a raphimg.nbh in its root, you'll get the 'no image' error message. Then, if you try to soft reset, but vol down is still somehow stuck, you'll never get out of bootloader. That's why I suggested pulling the battery earlier. When you power back on, it should just boot up normally like after a soft reset, but I might be wrong about that.
It's just not normal to randomly go into bootloader when you soft reset (and to stay there). Clearly, the phone is picking up the 'go into bootloader' signal somehow or other. Maybe it's not the physical button, but there's just some sort of bug that makes the phone think the button is being held down when you soft reset. Bummer, whatever it is, I hope you get it sorted out.
You might want to bite the bullet and hard reset. If you have some weird bug (and not a physically stuck down button) this should solve it. I bet you can hard reset ok. Hold vol down and the d-pad button and soft reset. You have to continue to hold down both buttons for a couple seconds after you soft reset. Then press vol up at the prompt.

I have hard reset a few times. I think I'm going to try not to turn off the phone unless i have to. i reset it a few times yesterday even after plugging it in for a little and its still good. i'll try it again when i get home because i need my phone during work.
thanks for your help!

"Converting data partition..." Problem

Alright, allow me to summerize to you guys the series of screw ups that happened in the day that I've had my captivate.
Basically, it's like this. I got this phone from my brother (it used to be his). Now when I got it, I began basically erasing his contents and setting up mine. The Phone is on the Cognition OS and everything seemed fine.
Now, when I tried to set up my google account, it said I had to do a factory reset, I did that. Then I realized the market place app was no longer there :/
I did another factory reset, still didn't help, and started looking around for info.
I told my buddy this and he said he could fix it. So he get's the update.zip for rooting the phone, sets it up on the SD card, and goes to root the phone normally. Except when he restarts the phone after, it doesn't go to the set up screen, so he just starts it normally and enters the setup screen by holding home+volume up+power.
Then he presses the reinstall packages, and the phone seems to get to work on the update pack...
Now, every time I turn on the phone the voice says "converting data partition to optimize extension four", turns off, then repeats.
I've looked up this problem and it seems to have something to do with voodoo, but the causes in the other cases the causes were different.
Can someone please help me out here? I've also tried doing a hard reset by holding the volume down button and pressing power, but nothing seems to take me to the recovery mode.
HELP.

Did you pull the battery during this our did you let it run? Should let it run.
Does your phone boot up at all?
At&t or rogers?
Do you have a windows pc with usb drivers installed?
What its your build number, located under battery, something like 1008?
Answer these questions and we can get you back up and running

-Well after he did the reinstall thing we let it run for like 15 minutes, then he pulled the battery out.
-The phone only shows the AT&T screen, say's the "converting data partition..." thing, then goes blank and does it again. I've let it run for like 10-15 minutes before having to turn it off because I couldn't have the speech going off.
-I have a windows PC, and but I'm not sure if I have the drivers installed. I have Kies installed and when I plugged the phone in before Kies could recognize the phone (though it wouldn't fully connect, it would just say "connecting" on the kies screen).
-The Model is SGH-I897, that's the only relevant thing I see under the battery, that good enough?
Thanks a lot.

No, your phone has a build, on phone under battery, the word build is not listed. Something between 1006-1012
If we are going to do this you need to be active, I can not wait 20 minutes in between responses

Sorry the internet kinda crapped out actually.
And I see a 1007 between the bar codes, that it?

Yes
Before we get started try this
Take battery, sim, ext sd our of phone
Plug usb into pc but not phone
Put battery back in
Hold volume up and down, while holding plug in usb
Screen should come on with android with shovel
You can pull the battery again
Confirm this happened

Yep, it happened.

It may be easier if we use gtalk, log in on your pc using google id, send me an invite [email protected]. This way we know when each other respond

Just sent u the inv

I am having the same issue.. Chairchair did your problem get resolved?
Can anyone help?
James

liquorsh0tz said:
I am having the same issue.. Chairchair did your problem get resolved?
Can anyone help?
James
Click to expand...
Click to collapse
Have you gone back to stock and then reflashed? Seems like some files are getting corrupted. Because you have a voodoo kernel I would follow these steps. Make sure to back up.
1. Use Odin to flash a non vodoo kernel.
2. Flash stock rom and master clear
3. Reflash rom of choice if it is 2.2
3a. If you want 2.3 follow the tut on it.
4. Breath a sigh of releive lol

Help!!! after hard spl intalation htc raphael doesn't respose!!!

Please help me guys . I tried to flash my phone. I conetcted the phone with active synch then on compiuter start the hard spl exe. Then i wait 2 minits and on my computer screen pop up new window and there write coz error 260. So then i dosconect the usb from pc , pick up the phone baterry wait 3 second then put battery to the phone but still doesn't response. I can push tur on button or reset button . But nothink!!!! please help what i need to do?

Before you flashed, you did make sure that you installed Microsoft .NET Framework 3.5 (mentioned in that same post)
Did any of the following happen?
*DO NOT start another process while the flashing process is taking place*
*DO NOT click off of the status bar... Let it stay in the foreground*
*DO NOT let the Screensaver activate*
(any of these can lead to a bad flash and possibly brick your phone)
Click to expand...
Click to collapse
If so, then you have possibly bricked your phone, my friend
Also, did you wait for it to sync and can you enter bootloader? Hold the volume down key and press the power key/reset button and release the volume down key when you see the multi-color screen.
Additionally, you should be able to remove all cards and your battery and be able to get into bootloader mode by holding the volume down key and connecting to your computer.

R^7Z said:
Additionally, you should be able to remove all cards and your battery and be able to get into bootloader mode by holding the volume down key and connecting to your computer.
Click to expand...
Click to collapse
I tried now to do it i insrt usb to pc and pocket pc then hold volume down key. But nothing. Mayby you have skype i wna to comunicate with you faster. And maybe you can help to me wat can i do now. Thx for answering

How long did you hold the volume down key? I have to wait at least 2 - 3 seconds from when I connect the cable to my device as I have the USB cable already connected to my PC. In other words, hold the volume key down while you are doing all of this, till you see the multicolor screen.

i can hold it 3 or even 6 minits. but you say something about the colours. when i install the spl with synchronization my phone just like died. i dont know wats hapen. and now i dont see any colours on my phone screen. now the screen is black.when i put battery in my phone about after 3 hours my phone back a litle worm. i dont know what to do.

That sounds like you bricked it. Sorry to hear but if you are positive that you did everything as the post I linked you to, mentioned, then it should work. I'm not sure where the process stopped working for you but perhaps you can try retracing the steps? Although, it does sound like you missed a step and now you're phone is bricked. I'm also not sure if you understand what I am saying or asking you to do but I guess if it isn't working, it just isn't working?

Synchronized Well I just shook my phone and the program's EXE file in the SPL. and then there shook far, far away and then threw away so that you do not click anything, not combine any other program. I do and do it. I've been waiting for. Then I look at my phone screen and blacked everything. Then dropped onto a computer error 260th And I do not know what I can do. It does not RESPOND at all. Even though I tried hard reset but still nothing happens. Maybe I should try to flash the phone to make a micro sd? Once uploaded there y card and then pressing a few buttons to be there? Extend the writing maybe?

I'm not 100% sure this will work unless you have HARD-SPL flashed to your device; which is where we stalled out the last time.
Once you have the stock ROM, rename it to RAPHIMG.nbh. Copy just that file to the root of your microSD (preferably a FAT32 formatted microSD but not required). Then, remove the SIM and hold the volume down key while you press the reset button and continue to hold the volume down key till you see the onscreen instructions. According to THIS post, this method should work for flashing a ROM. I am am not able to really say for sure that it does as I never really used or had to use the microSD flashing option.

This doesn't work to maybe i can somehow reinstall the original htc touch pro soft?

The only OTHER way would be through USB from bootloader but if you find it difficult to get that far, I don't know how else to help you my friend.

Maybe you can write a detail lession how can i do this? how can i louch that bootloader . Please help i realy need your help

Try it this way exactly:
Remove your battery, SIM and microSD. Now plug your USB cable to your device (not the computer). Hold the volume key down and plug the other end of the USB cable to your computer and wait till the multicolor screen comes up. If you do not see the multicolor screen, this may be an indication that the USB cord may be messed up (try another in this case), it may be the USB port (try another in this case) OR worse case senario, your phone is just plain bricked my friend...
Additionally, you may need to try another computer.
Once you get into bootloader we will need to go ahead and get hard-spl onto your device.
First, let me know when you get to the bootloader screen...

This doesn't work to ;(((((((((

I don't know what to say, it is sounding more and more like you've bricked your phone. Have you tried another cable / another USB port / another computer?

So, which raphael do you have? CDMA or GSM? And which hard spl did you flash: CDMA or GSM? And did you flash the raphael hard spl, or did you do something like flash the diamond hard spl (or the unlocker)?
If soft resetting the phone doesn't bring it back, then it's probably bricked. I have a feeling you flashed the wrong bootloader for the device.

so if i bricked my phone. No i can just throw it to the dump. or maybe i i send this phone to the repair shop. Maybe they gona repair it?

So, what bootloader did you flash, and what model do you have? If it's the wrong combo, I guess you could sell it on ebay for spare parts. You're not likely to get it fixed.

i have t-mobile mda htc touch pro. and i tried to flash it with Raphael_VZW_HSPL_035

My friend, if you flashed that to your phone, your phone is now bricked from what I can tell. T-Mobile is GSM, that HSPL looks to belong to Verizon which is CDMA. I could be wrong but if you failed to read, then obviously you really didn't need to do it. :enter sad face of choice here:

It's dead. Just put it up for sale on ebay; someone may give you 20-50 bucks for it.