Debug mode !! KITL Mode Enabled !! - Non-Touchscreen Windows Mobile Other

Hello experts,
I'm dealing with a very strage issue ...I have a HP Ipaq 514 voice messenger, and now the phone doesn't start with windows ce6. When I start it, it returns the following:
Debug mode !!
KITL Mode Enabled !!
and blocks in this screen... Is there any key combination to solve this issue ??
Thanks a lot in advance for your help !!
Best regards,
Alexey

Related

ERROR 150 ROM UPGRADE UTILITY ERROR

Hello everyone,
I have a big challenge for the experts of upgrade process.
I have tried to upgrade my S100 with a French ROM (EXE method) and the upgrade stopped at 76% while CE upgrading. Since, I had to remove USB cable.
Now my PDA is off. Impossible to turn it on. Even hard reset keeps the screen black.
I have tried to run the upgrade tool again but no info are detected and the soft gives me the following result :
"ERROR 150 ROM UPGRADE UTILITY ERROR"
Does someone know about a way for revival my Phone?
I thank you in advance for your support.
Laurent
:-( Tried the bootloader (camera & power & sof-reset pressed together till it reads 'serial v1.xx')? If this works connect USB & restart the upgrade.
M
I knew that some genius live on this Forum
I didn't but I just did and it worked fantastic.
Thank you so much for this info unknown to me. Very precious.
Thank, thank and thank you again.
Laurent :lol: :lol: :lol:

Imate jamin in bootloder PM300

plz let me solution of Imate Jamin PM300, i had done resetting and formating .
When i m power on button the phone display startup screen and immediately in bootloder mode or test mode.
Thnx
BR
sarbi said:
plz let me solution of Imate Jamin PM300, i had done resetting and formating .
When i m power on button the phone display startup screen and immediately in bootloder mode or test mode.
Thnx
BR
Click to expand...
Click to collapse
same problem

I Mate Jam Problem , Please Help

Hello XDA Community !
There is some thing wrong with my Jam ..
i upgraded it with 2.03 TX .. it worked for a while .
Now when i power it on .. i see just the Blue i-mate booting screen .
i stay forever ..
My PPC establish a connection with AvtiveSync normaly .. and i can read it's contents by ActiveSync ...
But..! .. When i do a soft or hard reset .. it goes to bootloader mode always ..
when i try to upgrade room by any nethod .. it doesent work ..
always connection error
evin with jafWM .. connection error!
When i run roomupdate.exe and go to usb command prompt .. i can type task 32 and Enter normally .. but .. when i typr three characters after that .. it hangs for long time .. and nothing happen
i've been tired of this problem ..
Please help me to be able to use my PPC again!
Thanks to all
yoga mat
The Dreadfulness Of Spam.
Hmmm i need a better description of your problem. Have you dissembled your magician recently ? What error it gives you after you try to update the ppc ? Error 114 ?
Check out my post
http://forum.xda-developers.com/showthread.php?t=424259

[Q] HELP ! HP IPAQ 314-316 navigation system dead !

Dear Masters!
I would like to ask for help. I've got a HP IPAQ 314-316 navigation system, it does not, it does not take up the charge, only one can enter into Engineering Mode. The computer does not recognize, so I can not even run the official ROM Update.
My question and my request would be that someone could not felrakni SD card ROM update for some solution to at least the USB connection meglegyen.
The Engineering Mode Nboot is possible to update, which should Nboot.bin
Engineering Mode is the option to update Eboot, which should Eboot.nb0
Perhaps if we had these two, you can identify the computer and I could put back the original state.
Thank you in advance for your help

[Q] Windows Mobile 6 Won't boot after first soft-reset !! Black Sceen !! PLEASE HELP!

Hi ! I have an Acer P300 Windows Mobile based device . I have tried to install Android on it ( i was able to install the rom from a device named GeeksPhone ONE which has the same hardware specs. ) , after the installation the screen was on , but all black . After that I've reinstalled my original FW . All went good , only that my phone wasn't reading my SIM CARD and no WI-FI connections ( although I was able to connect with the wifi at a point ).
After a Soft-Reset ( shutdown and startup ) the phone shows the Acer logo with the FW version , and after that the same black screen as with Android .
It might Android damaged my hardware ???
Now my device won't turn on at all .... No vibration on power button , no bootloader , nothing . Please Someone can help me ?? At least some notes ... One reply from you won't hurt !
P.S. Still waiting for some answer !
Now my device won't start at all ... Is completely DEAD !!! ...
If someone will want to answer , I need some help with the battery , I believe that is not charging anymore ! ...
Anybody with the same problem around here ?
lol have your same problem mate xD tell me if u managed to fix this pls

Categories

Resources