Hi,
I have just upgraded my ROM with the new leaked one.. the performance though is now superb.
The problem i m facing now is the speaker phone is not working. the earphone volume too is a bit slow than before
2ndly the usb modem problem is still persistent, my laptop gets connected with my atom through GPRS but soon after connection the incomming bytes tend to slow down & eventually no incoming bytes; i have to disconnect & connect it all over again, and repeat this many times till i get my work done this way...
is there any problem with my usb modem driver which i installed on my laptop or something else.
3rdly how can i get smart dialing option on my phonepad... i tried to install intellidialerpro but it doest seem working for atom.
Kindly suggest.
hello everyone,
I cannot get Activesync to recognize my htc touch pro no matter what i do,... i've uninstalled and reinstalled shut everything off then on, followed all of MS's advice, and nothing works,...
Any suggestions,...? No problems connecting my tytn II and my hermes,...
thanks,
ek
Are you running any firewall software? If so, this is relevant to you.
start>>settings>>connections>>usbtopc>> un check the "enable advanced network functionality"
sorry attnoob, was trying for your quick fix, but it didn't work,... thanks anyway,... now will go to the firewall issues noted above, but i already opened the ports as per ms's recommendations in help,...
will try other suggestions and get back to you,...
ok, so allenh, read all the info at the link you sent me, and actually did all these things yesterday, but it didn't work,... also, something strange happens when i hook the device to the PC in that, the device immediately goes to the 'internet sharing' program you use when tethering, it establishes a connection with the internet, and there is a comments saying 'check usb cable connection' and this never happened with the tytn II,...
your help is appreciated,...
ek
Check the USB cable
It seems the USB cable the Tilt uses and the one the Raphael/Fuze use are different, If i use the cable that i usued with my tilt the computer would not recognize the Fuze it will charge it though, only if i use the usb cable that came with the Fuze it works fine.
Are you using the stock ROM or a cooked ROM. Some of the new cooked ROMS are having this problem.
Also, are you using Vista or XP. The problems seem to be with XP.
my fuze seems to also be having this issue... i can hear my laptop do the little noise saying something is attached but my phone never pops up with the screen anymore asking what i would like to do. sometimes i get lucky and it will randomly connect to active sync but would not give me any warning whether it was going to work or not.
btw, it didnt start doing this until i flashed NATF's v2.1 and also loaded a custom theme and toolbars and such.... it worked after i loaded NATF's rom, just randomly stopped at some point after that.
if you are putting on a new rom then put the phone in bootloader mode it worked for me
LostcauseZ06 said:
my fuze seems to also be having this issue... i can hear my laptop do the little noise saying something is attached but my phone never pops up with the screen anymore asking what i would like to do. sometimes i get lucky and it will randomly connect to active sync but would not give me any warning whether it was going to work or not.
Click to expand...
Click to collapse
My Fuze is doing this too, excep every single time. I can't get Activesync to work through USB. And I'm running the stock ROM. Internet Sharing automatically connects.
Okay, I set Internet Sharing to Bluetooth PAN (instead of USB), which kept it from automatically starting when I plugged in the USB. This let ActiveSync and the 'choose a connection type' startup on my Fuze and everything has been fine.
Try your PC Network settings
Hi,
I have the same problem recently. My AS does not want to recognize my Raphael. What I did was go to the network setting of the PC (Network Connections) and disable the 1394 adapter. Then my AS now can recognize my Raphael. The next unsolved thing is how to make the connection stable enough to make happen the syncing.
Drax
Hi, I had similar problem. Once upon a time the connection between my Touch Pro (WM6.5.3) and PC stopped working. Activesync did nothing and after a minute gave error message with troubleshoot guide. So I opened control panel ---> device manager (with mobile connected via USB), where I found "Windows mobile based device" between network adapters. I opened it and under it's advanced settings I found "network address" which was set to "unavailable". So I changed it to 192.168.2.2 and now it works again ;-)
Hope it helps someone ;-)
Many times it happens that I am not able to connect my g-smart i120(wm6) to my laptop I tried serial option instead of USB, it connects only sometimes not always No Idea what to do! Help me!
I had experienced something similar and i ended up deleting the sync relationship on both devices and reinstalling Activesync. You could alternatively just reinstall activesync and see if it works.
hi guys,
i m facing the problem when i connect my windows mobile2003SE to Pc via sync it shows error
''can not exute repllog.exe''
even i hard reset many times but i m still facing the same problem
plz help me.
thx.
Hi!
I managed to port some builds of Windows Phone 6.5 successfully to my Smartphone BenQ E72(Kyocera E4000), but I had problems with each of the builds of WP 6.5......The Wi-Fi dissapears often =S
In Windows Phone 6.0-6.1 this doesn't happen, only in Windows Phone 6.5....You must reboot the device and if you have luck, the WI-Fi appears again
Anyone have any idea why this happen?
Thanks
Sorry I'm not able to help, but I have the similar problem. The wifi often turns it self off and on again. It probably happens a few times every 10. minutes. I have no idea why, its not only with my home wifi, it does the same at work also.
I don't know why this issue happens only in Windows Phone 6.5....The Wi-Fi function dissapears from CommManager and Settings and there's no way to enable it...You must reboot the phone and the Wi-Fi function appears again (sometimes)
I've noticed some other roms with it playing up with other connection types- possibly its a flaw with the com manager.
Try looking for different solutions for the com manger? like 3rd party ones- or see if the 6.1 one can be copied to 6.5
Hi,
I've got yesterday sw2. It is really cool, but sometimes i have problem with bluetooth. Sw2 seems to be connected with phone, but when i start some app, it is loading, but this app don't start. I must restart my watch and then everything works fine, but then when i don't use it for a while it didn't want start against. I am using nexus 5 with custom rom. Where can be a problem?
I am having the same problem. Also a nexus 5 with custom rom. Maybe this is a nexus issue?
Which kernel are you running on the phone.
I am using latest Droidkang rom with stock cm kernel.
Some times I will clear phone's RAM to temporarily resolve this problem.
Any ideas anyone? I have the same problem on stock 4.3 on HTC One Max. It drives me nuts ^^
Stock Nexus 5 has no such issue so I'd start with the kernel /ROM bluetooth compatability. Certain apps seem to lose their state occasionally I've noticed. They generally just need to be closed and reopened though. No reboot has been necessary.
Sent via telepathy
Difficulty with MediaTek devices
I have a Wiko Stairway, which is built on MediaTek platform. Pairing is difficult but possible. I don't know whose fault it is, MediaTek or Sony or both?
Still I find it awkard that I have to install 10MB of Sony software just to establish a faulty connection.
My workaround:
Pair the devices without installing the Smart Connect suite
Install Smart Connect and restart watch
Start Smart Connect and wait a while. It should now find the watch and prompt for installing the add-on
Turn bluetooth off and on on both devices
It should now work
Problem is that every now and then the connection is dropped and you may have to toggle bluetooth on either watch or phone or both. Even sometimes a restart is required.
A work around might be to see if force closing the app 'bluetooth share' temporary resolves the issue. If that's the case you could set up a tasker task to kill bluetooth share every 8 hours or so. You might need a plug-in to properly kill bluetooth share with tasker.