i have a htc tytn2, no lock
its dutch, did the update from mobile 6 to 6.1, no problem
when i want to update with a different rom, (even hard spl tried it also)
i run the KaiserCustomRUU it works til i get the %, it stays at 0% and after a time i get an error 262 update error.
can somebody give info to update my radio, the original radio from htc is not good and when i am calling i have an echo.
total rom update even to English is no problem. but it wont update....
anybody?
mrijnvis said:
i have a htc tytn2, no lock
its dutch, did the update from mobile 6 to 6.1, no problem
when i want to update with a different rom, (even hard spl tried it also)
i run the KaiserCustomRUU it works til i get the %, it stays at 0% and after a time i get an error 262 update error.
can somebody give info to update my radio, the original radio from htc is not good and when i am calling i have an echo.
total rom update even to English is no problem. but it wont update....
anybody?
Click to expand...
Click to collapse
There are some ideas in here for getting past 262 errors: http://wiki.xda-developers.com/wiki/RUU_Errors
Ta
Dave
@ daveshaw
thanks, but after soft reset its starting up normaly, next update the same, always that fault...
nobody, any ideas??????
mrijnvis said:
nobody, any ideas??????
Click to expand...
Click to collapse
Try re-installing active sync and try again. Error 262 usually means that connectivity is lost between your USB and phone. Re-installing active sync might solve the issue.
Also try and do a forum search using the search option right at the top of the page using the key words "Error 262" you might get some more inputs on how to sort this.
Related
Please help. I wqas trying to update my radio rom to 1.13 but the error 114 appeared and asked me to disconnect my imate jam and do a soft reset. I did that but its stuck with blank screen that shows SERIAL ta the top of the screen and V1.02 at the bottom. I tried removing the battery and replacing it back but it still shows the black screen.. now im stuck please help...
Have you tried hard resetting at the bootloader screen (this is the SERIAL
screen)
Hard reset is:
__ + __ + Reset button
hi
i tried hard resetting but it didnt make any difference.. now i nearly had a heart attack... what i did was reconnected my imate to my pc and ran the rom update again... to my surprise it did the update then asked me to hard reset... thats it my radio version in now updated... now im going to observe its behaviour first before installing everything again...
cheers
Good to hear, looks like everything went fine.
What ROM are you using? Just curious
Jorgee said:
Good to hear, looks like everything went fine.
What ROM are you using? Just curious
Click to expand...
Click to collapse
hi its:
Rom Version 1.12.00WWE
Rom Date May 28, 2005
Radio Version 1.12.10
Protocol Version 1337.42
ExtRom Version 1.12.171WWE
now im reverting back to the original rom version then ill update the radio version with 1.13 just in case i made a bad patch cos of disconnecting it during update.. :lol:
ayos to!
It looks like you are using a very old rom, BTW, the newest RADIO is 1.04.10....
Do you have a Vodafone v1640?
no i am using imate new jam. imate says it has the latest rom version.
Oh, sorry i thought it was a Universal....
Well hope everything is now okay
Please help me out here... Got my new G4 Prophet screwed during upgrading... Now it can't boot up at all.. Bootloader is working tho, could somebody send me a SD dump image for G4 Prophet? Thanks a lot!!!
Anyone please help~~~ Thanks a lot!
leiz_ca said:
Anyone please help~~~ Thanks a lot!
Click to expand...
Click to collapse
why do you need an SD image, you can use a ROM updater to fix 95% of the problems
Thanks, Jesterz. You are right, I got it fixed an hour ago... here is the story, just in case it may help other people later.
Got my XDA Neo and it was in Chinese rom, which has Wi-fi disabled. So I tried to upgrade to AKU3.2. but there was an error, something like "Can't write" or similiar. Then cellphone just stop responsing. Tried soft-reset and hard-reset, both stopped at splash screen (where shows the version of IPL/SPL). Bootloader still working tho.
Then try to download some rom from xda-developers, especially that stopatbootloaderfix, but the updateutil just can't update it, report different types of error code. Others just complain no connection through activesync has been established. After trying for over 5 hours and got desperate, that was the moment I login here and ask for help.
Today I tried the stopatbootloaderfix again but this time with "Allow USB connection" disabled in ActiveSync... and it works! It successfully flashed the ROM and now I am running the new AKU2.3.1 rom!
Happy....
Same Prob
Hi, where i can find this stopatbootloaderfix?
Looks i have the same problem. my Prophet stays at the Splashscreen with IPL, SPL, GSM, OS :-(
OK, worked it out by pressing and holding the powerbutton while performing a softreset
leiz_ca said:
Thanks, Jesterz. You are right, I got it fixed an hour ago... here is the story, just in case it may help other people later.
Got my XDA Neo and it was in Chinese rom, which has Wi-fi disabled. So I tried to upgrade to AKU3.2. but there was an error, something like "Can't write" or similiar. Then cellphone just stop responsing. Tried soft-reset and hard-reset, both stopped at splash screen (where shows the version of IPL/SPL). Bootloader still working tho.
Then try to download some rom from xda-developers, especially that stopatbootloaderfix, but the updateutil just can't update it, report different types of error code. Others just complain no connection through activesync has been established. After trying for over 5 hours and got desperate, that was the moment I login here and ask for help.
Today I tried the stopatbootloaderfix again but this time with "Allow USB connection" disabled in ActiveSync... and it works! It successfully flashed the ROM and now I am running the new AKU2.3.1 rom!
Happy....
Click to expand...
Click to collapse
Are you telling me this solution is also for error 326? If so Darn!!!
Don't remember whether i had a Error 326 or not.. Sorry..
Was installing duttys rom when my anti-virus program started. Update failed and since then all I see is the tri-colour screen. Sometimes I can get the rom updater to recognise my TyTNII but it will not continue to upgrade. Any suggestions. Have tried mtty1.42 but it doesn't seem to have a usb port option, have tried hard reset etc with no luck. Any suggestions would be greatly appreciated.
An update, I have tried several rom updates since, most get to the stage where the progress bar is shown and the stop. The HTC update to revert to shipped rom gets to 1% and then tells me that this rom is not suitable for my pda!
How about some more information...
What is your Tytn II - Tilt or HTC?
What Rom was on it before you tried upgrading?
What Radio was on it before you tried upgrading?
What version of Duttys did you try to flash?
Did you upgrade to HardSPL before you tried flashing?
This should enable someone to begin trying to unbrick your phone.
Also DO NOT USE MTTY unless you know what you are doing - it can seriously kill your Tytn if used incorrectly. Wait for GSLEON3 to swing by before trying this - but he's very busy at the moment helping others unbrick their toys so you may have to wait for a while.
If you had an original rom/radio from AT&T or HTC it shouldn't hurt trying to download an original rom and try to flash - preferably using your SD card.
Also, while you're waiting for someone to help, have a good read through the Kaiser Wiki (in my signature) before trying anything else.
what are the steps that u take? let us know if u are missing any
HTC TyTN 11, Was using Q-mobile 1.2 but couldn't install tom tom navigator 6, don't know what radio it was using because i hadn't got that far. Was trying to flash Dutty's 6.1 and I had run jumpspl from device because I got the white screen when I treid to run 1.93 so installed 1.56 to pda and ran it. this worked to insatll Q-mobile this morning.
Hope this helps!
what are the steps that u take? let us know if u are missing any
Try to reset pda keep getting tri-colour, attach usb and usb shows at base of screen. When i try to install rom The problem in my second post occurs. I cannot hard reset device to anything other than the tri-colour
Thanks for your help, I tried one of the roms indicated and it worked! I have spent so much time reading various wikis and downloading files. I'm not entirely sure why it worked this time but I'm not about to ask questions! Thanks again!
OK, now you've got your phone working again, make sure that you get HardSPL installed before you try anymore flashing.
ok i was installing KAIS_Radinly_0.26.07.06_CustomRUU and it froze at 96% and now my phone is bricked!! every time i restart the phone its stuck at the RED GREEN BLUE and WHITE screen.. i tried using mtty but then im not trying to mess my phone up any more. i dont understand how to fix it.. if i download a new ROM and put it on my SD card then how do i read it with my phone? sorry guys, im a noob at this as you can tell..
nm guys. i just ran the new rom and it worked! haha sorry for posting too quick!
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
xmooglex said:
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=KaiserFAQ
your answer is in there
whenever i try to ugrade my rom i get this 262 error. so then i tried to do the official wm6 rom from at&t for my att tilt but it went through the whole process of upgrading but after it said it was finished it rebooted my device and nothing changed. it was still the regular wm6 that comes on the phone. It says my ROM version is 1.62.502 and my RADIO version is 1.27.14.09. How am i supposed to upgrade and what can i upgrade to . Im trying to use hyperdragon. Please respond asap Thank you
wmontae said:
whenever i try to ugrade my rom i get this 262 error. so then i tried to do the official wm6 rom from at&t for my att tilt but it went through the whole process of upgrading but after it said it was finished it rebooted my device and nothing changed. it was still the regular wm6 that comes on the phone. It says my ROM version is 1.62.502 and my RADIO version is 1.27.14.09. How am i supposed to upgrade and what can i upgrade to . Im trying to use hyperdragon. Please respond asap Thank you
Click to expand...
Click to collapse
Read First, ask later. This problem has been asked a thousand times. Hard reset & Re-install activesync.
Moderators please close this thread!
I have an Qtek S100 and according to the imei check its an o2 rom.
After a long time i decided to use my qtek again just for fun and see what i can do with it.
In windows 2003se it keeps giving low battery although its connected to usb, anyway i decided to give it a go and installed wwe05 but totally forgot about the radio rom that needed to be 1.12. (it was 1.13).
So it gave "bad radio" during startup.
I tried to flash it with multiple radio roms, including the original o2 one, but some dont start at all and some keep getting stuck at 45%.
and eventually give error 114, i can flash it back to original rom, but as soon as i want to update the radio, same thing happens.
now it gives "no radio" in wwe05, and after flashing back to 2003se it says "no gsm".
the radio wasn't giving any error/problem before i decided to update the os, so i doubt it's an hardware issue. i checked mutiple threads about 114 radio, but haven't found a sollution yet.
maybe somebody here can help me get my radio back.
You should read this Thread first http://forum.xda-developers.com/showthread.php?t=705702. Maybe there is the Solution.
i tried them all with normal usb flash, they all stop at 45% and give error 114.
Next Idea is here : http://forum.xda-developers.com/showthread.php?t=494635&page=2
Dont use a USB HUb !
k, i charged battery as long as possible, (althought i think its nearly dead) it now shows 100%.
I'm also using a different system now with windows 7,, when trying to flash it doesn't give an error, but after a few seconds its shows "congratulations", but it hasn't done a thing....
i can only try a windows xp in vmware, will try next first.
nvm, tried multiple roms, guess one of them changed my bl, cause its showed version 1.5.0 when its needs to be 1.00 or 1.02, so i tried to update my bootloader with pnewbootloader and version 1.02.nb0 and it resulted in an error ITFlashRom and never came back to the living. no boot no bootloader. paperweight is going in the bin. topic can be closed.