whenever i try to ugrade my rom i get this 262 error. so then i tried to do the official wm6 rom from at&t for my att tilt but it went through the whole process of upgrading but after it said it was finished it rebooted my device and nothing changed. it was still the regular wm6 that comes on the phone. It says my ROM version is 1.62.502 and my RADIO version is 1.27.14.09. How am i supposed to upgrade and what can i upgrade to . Im trying to use hyperdragon. Please respond asap Thank you
wmontae said:
whenever i try to ugrade my rom i get this 262 error. so then i tried to do the official wm6 rom from at&t for my att tilt but it went through the whole process of upgrading but after it said it was finished it rebooted my device and nothing changed. it was still the regular wm6 that comes on the phone. It says my ROM version is 1.62.502 and my RADIO version is 1.27.14.09. How am i supposed to upgrade and what can i upgrade to . Im trying to use hyperdragon. Please respond asap Thank you
Click to expand...
Click to collapse
Read First, ask later. This problem has been asked a thousand times. Hard reset & Re-install activesync.
Moderators please close this thread!
Related
Was installing duttys rom when my anti-virus program started. Update failed and since then all I see is the tri-colour screen. Sometimes I can get the rom updater to recognise my TyTNII but it will not continue to upgrade. Any suggestions. Have tried mtty1.42 but it doesn't seem to have a usb port option, have tried hard reset etc with no luck. Any suggestions would be greatly appreciated.
An update, I have tried several rom updates since, most get to the stage where the progress bar is shown and the stop. The HTC update to revert to shipped rom gets to 1% and then tells me that this rom is not suitable for my pda!
How about some more information...
What is your Tytn II - Tilt or HTC?
What Rom was on it before you tried upgrading?
What Radio was on it before you tried upgrading?
What version of Duttys did you try to flash?
Did you upgrade to HardSPL before you tried flashing?
This should enable someone to begin trying to unbrick your phone.
Also DO NOT USE MTTY unless you know what you are doing - it can seriously kill your Tytn if used incorrectly. Wait for GSLEON3 to swing by before trying this - but he's very busy at the moment helping others unbrick their toys so you may have to wait for a while.
If you had an original rom/radio from AT&T or HTC it shouldn't hurt trying to download an original rom and try to flash - preferably using your SD card.
Also, while you're waiting for someone to help, have a good read through the Kaiser Wiki (in my signature) before trying anything else.
what are the steps that u take? let us know if u are missing any
HTC TyTN 11, Was using Q-mobile 1.2 but couldn't install tom tom navigator 6, don't know what radio it was using because i hadn't got that far. Was trying to flash Dutty's 6.1 and I had run jumpspl from device because I got the white screen when I treid to run 1.93 so installed 1.56 to pda and ran it. this worked to insatll Q-mobile this morning.
Hope this helps!
what are the steps that u take? let us know if u are missing any
Try to reset pda keep getting tri-colour, attach usb and usb shows at base of screen. When i try to install rom The problem in my second post occurs. I cannot hard reset device to anything other than the tri-colour
Thanks for your help, I tried one of the roms indicated and it worked! I have spent so much time reading various wikis and downloading files. I'm not entirely sure why it worked this time but I'm not about to ask questions! Thanks again!
OK, now you've got your phone working again, make sure that you get HardSPL installed before you try anymore flashing.
ok i was installing KAIS_Radinly_0.26.07.06_CustomRUU and it froze at 96% and now my phone is bricked!! every time i restart the phone its stuck at the RED GREEN BLUE and WHITE screen.. i tried using mtty but then im not trying to mess my phone up any more. i dont understand how to fix it.. if i download a new ROM and put it on my SD card then how do i read it with my phone? sorry guys, im a noob at this as you can tell..
nm guys. i just ran the new rom and it worked! haha sorry for posting too quick!
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
xmooglex said:
okay i have one problem after fixing it. i downloaded the TEST rom for the ATT tilt and now every time i reboot my phone it says 'TEST ONLY. NOT FOR SALE.' how do i get rid of this? when i installed a new rom it still says this and i even tried hard resetting my phone but it did not reset anything to factory settings. it just reloaded the rom that i last had!
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=KaiserFAQ
your answer is in there
I'm trying to create a factory standard HTC three uk rom as there doesn't appear to be one already cooked. I followed the wiki guides to dump and cook my rom. However when flashing it always fails at 25% any ideas? i have re-tried cooking and flashing several times, still same error.
info
The rom is wm6.0 and radio 1.27.15.32
before flashing i successfully flashed my device with L26's new throttle rom (beta 6)
Do you get an error message when it fails?
Thanks
Dave
sorry for the late reply i re-flashed tonight as i could not remember error, its error 262 "the rom update utility encountered communication errors during the update process"
Sorry to ask but, have you installed Hard SPL yet?
Dave
yes i ran hard spl version 1 before flashing, i have sucessfully flashed other roms just not the one i cooked
Hello,
First my question :
I'm now thinking about reinstalling official ROM but my question is : should I remove Hard spl and move back to initilial IPL/SPL before loading the WM5 rom.
Then the context:
I'm a newbie and 2 days ago I've tried to upgrade my I-Mate K-Jam to WM6.1.
After having carrefully read several thread and in particular the thread "Wizard Windows Mobile 6 for newbies" i first start to unlock my G4 mobile with HardSpl. This was a great success so I moved on to the next step loading a WM6 ROM. I choose the WizFlo 6.1.1.4 (http://forum.xda-developers.com/showthread.php?t=435228) but this was not a success since my K-Jam was just looping on the splash page/alignment wizard and reboot. I really thought that I had turned my mobile into a brick but was still continuing to investigate and yesterday evening I've learned how to just start the bootloader by pressing the camera button while starting-up. Yepee, 2 a clock this morning, I succeed loading the vanilla version of the TNT rom : http://forum.xda-developers.com/showthread.php?t=388229. Super everything was working fine so I went to bed.
This morning, very proud of what I've done alone I just decided to move from the TNT vanilla version to the professional version. This was a mistake since then I was never able to restart my K-Jam. It just freeze on the TNT splash screen. I've tried to reload several other rom but the TNT splash screen remains and my mobile just continue to freeze.
I'm now thinking about reinstalling official ROM but my question is : should I remove Hard spl and move back to initilial IPL/SPL before loading the WM5 rom.
Thanks in advance for your help
YES!
In order to revert back to official rom,you'll first have to remove HardSPL,otherwise it'll Brick the phone.
Secondly, have you tried a Hard Reset,it might help the phone to start working.Is your battery fully charged ?
After getting the phone HardSPL,there's no reason for any wm6 roms like TNT to stuck up,it might be that the battery is weak or flat.
Get the battery fully charged,try a Hard Reset,otherwise reflash TNT.
Thanks for your answer, I'm not sure about the batterie status. Am i able to refill the battery in bootload mode. or does the official K-jam charger work in my mobile is not yet started.
Almost a week I'm working on my mobile but no sucess yet.
One more question, Is there any special restart or reboot to be performed once the rom load process is complete ?
I've tried to install Loverom or merlin rom but even if the splash page change I never go furher. I'm now considering on moving back to an official ROM. But since I didn't backed up mu rom before all of these update process I'm gone use a download one.
K-JAM_WWE_216901_2169101_020710_ship.exe. This official package install a ROM file and the RUU utility, but how can I check that the rom does not contain IPL nor SPL file.
Is there a way to check rom content before a load. I'm using hardspl and I've read that if I instal a ROM with IPL/SPL i will turn my device into brick.
May be I should also remove hardspl but how can I do this ?
Solved !!
I just notice a format error when hard reset.
Google it and find his thread
http://forum.xda-developers.com/showthread.php?t=428312&highlight=format+error&page=3
Fixed yepeeee.
thanks to all for your help.
Good that you solved it finally, Happy Flashing
Hi, I hope this is a good place to put this question, I would put this in the Vogue forum but it looks kind of slow-moving, so I figured I might as well turn it over to the experts. I encountered a problem on my first real ROM flash and now I'm kind of worried to try it again. So:
I'm using a Verizon XV6900/Vogue/TouchCDMA. I flashed to the leaked Verizon 6.1 upgrade, which worked flawlessly, and enabled Win 6.1, EV-DO Rev. A., and GPS with the Valhalla CAB. Then I decided to try some custom ROMs.
I unlocked without a problem, and confirmed that I achieved 2.31 coke. I then lauched the ROM update utility on a WDM ROM I got from here. It got hung up 69% through, the RUU tried to help me but failed at 69% again. It gave me an error 262 connection error, but couldn't give any more details.
I thought I had bricked my phone, but while stuck on the three-color screen I flashed back to the leaked Verizon ROM and authenticated, now I'm fine.
I'm guessing that the Verizon radio (3.37) wasn't new enough, since most other ROMs require the new Bell 3.42.
The actual question part: Should I update my radio and try WDM's again, or should I give something else a shot? I'm looking for something stable that includes M2D, and some of that new Opal stuff (title bar, Youtube, etc.) OMJ's also looks promising.
P.S. What exactly is User customization, and will flashing a non-carrier-specific ROM like this one affect my ability to connect to Verizon?
it isn't a problem of being "new enough" it has to do with radio compatibility.
That page specifically says flash version 3.42
I imagine user cusomization is refering to "uc" compliant roms that allow you to automatically install cabs from your storage card after a flash
Hmm, I really don't see a mention of it on the page, I guess I'm just supposed to assume 3.42 because it says simply, "update radio." Thanks though.
EDIT: Well I used a ROM that's compatible with 3.37 compatible, and it works great. I guess this thread is over now.
Hi guys, my raphael was working good when stoped working the EDGE radio, it connects right on the anthem, but doesnt get signal, loosing the information with the connection timeout reason.
I think it is my radio, I have never messed with raphael HardSPL, just installed the rom 5.05.401.1 WWE official HTC rom disponible on the official HTC WEBSITE, only clicking on the file.
And I updated my radio too, installing the 1.11.25.01 version, official to the fuze, it was working so good, suddenly it broken the signal and have already passed 5 days.
I was thinking about re-installing the radio, seems that when I installed the 1.11.25.01 Radio version I didnt need to loose all my installed programs, data etc, only updating the rom, not loosing information as in the ROM installation.
I would like to re-install this rom version, or the last and best rom version with loose my data, I didnt remember the procedure, if I needed to instal the HardSPL or no, but by my remembering, only executed the .exe files on the desktop
help please!
i was needing this help so much, please help me guys, i tested my chip on another mobile and worked the edge
Be sure to flash Hard SPL before you do anything!!!!!
After you do that, you can go ahead and flash.
If I were you, I'd flash a different radio to see if it works better, I recommend .28, .32, and the .19 test.
If that doesn't work then let us know.
basmareck said:
Hi guys, my raphael was working good when stoped working the EDGE radio, it connects right on the anthem, but doesnt get signal, loosing the information with the connection timeout reason.
I think it is my radio, I have never messed with raphael HardSPL, just installed the rom 5.05.401.1 WWE official HTC rom disponible on the official HTC WEBSITE, only clicking on the file.
And I updated my radio too, installing the 1.11.25.01 version, official to the fuze, it was working so good, suddenly it broken the signal and have already passed 5 days.
I was thinking about re-installing the radio, seems that when I installed the 1.11.25.01 Radio version I didnt need to loose all my installed programs, data etc, only updating the rom, not loosing information as in the ROM installation.
I would like to re-install this rom version, or the last and best rom version with loose my data, I didnt remember the procedure, if I needed to instal the HardSPL or no, but by my remembering, only executed the .exe files on the desktop
help please!
Click to expand...
Click to collapse
I cannot say if your radio is the problem. If you're installing an official HTC or provider ROM, you do not need HardSPL. If you want to install a cooked one here off XDA, you do. This great guide will help you flash a cooked ROM and/or radio: http://forum.xda-developers.com/showthread.php?t=448008
You're right, if you flash a radio, then you will not lose anything in your Storage Memory. If you flash a ROM, you will, so be sure to back up your PIM. PPCPimBackup does a great job for that, you can find it at d0ugie's site: http://blownfuze.org/ Your contacts and calendar should come back right away after the restore, but the messages take a while to rebuild, so don't touch it for at least 15 mins after the reboot.
I was trying to flash the HardSPL, and it goes to an ERROR
Trying to flash a Radio goes to an ERROR too, my raphael is only accepting the official's HTC ROM, when flashing anything it cracks on 0%
wtf?
basmareck said:
I was trying to flash the HardSPL, and it goes to an ERROR
Trying to flash a Radio goes to an ERROR too, my raphael is only accepting the official's HTC ROM, when flashing anything it cracks on 0%
wtf?
Click to expand...
Click to collapse
By default, you cannot flash anything but an HTC or provider ROM; you cannot flash radios either. You have to flash HardSPL before you flash a custom ROM or a radio.
Have you tried running SSPLManual.exe as outlined in the guide above, step 2 note 2?