Related
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
I have an at&t Tilt. I am having a problem with the device automatically powering off during the Windows screen while loading.
To get to where I am at:
1. I followed the instruction to install the HardSPL from HERE. On my bootloader screen, I see:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
2. Then I did the Sim Unlocker procedures found HERE. After completing step 5, the device rebooted, the AT&T icon displayed, then the screen goes blank and stayed that way.
3. I found the fix for the black screen problem HERE. It was a radio problem, and I needed to update the radio to a compatable radio.
4. My phone worked fine for a day. The next day, my phone just died and when I rebooted, it said critically low battery. After I tried to charge it overnight (with AC adapter charger), it was still critical low battery. Then I tried USB charger for the day, still critical low battery. I figured it was a SPL-Radio conflict.
5. Then it stops getting into Windows altogether. It will power off at the Windows loading screen. I let it charge all day. I suppose that the battery is not dead because it is able to stay on the Tri-Color screen without being plugged in, and it always turns off at the same exact point while loading Windows.
6. I still can get to the tricolor screen. I can see USB when plugged and serial when unplugged.
7. I can flash ROMS, and I will even see the different Windows loading screens (Dutty's screens are different than the AT&T green Windows screens.) I have tried original AT&T and cooked WM6.0 Roms/Radios, WM6.1 Roms/Radios. It still keeps rebooting at the Windows loading screen. I tried the original and cooked roms from HERE.
8. I tried accessing the phone via MTTY and use the "boot" command. I still don't fully understand the boot command and what exactly it does, but from my understanding, it resets the boot loader chip.
9. I would like to update the SPL -- instructions HERE. But since I can't fully boot the phone, I can't actually run the Soft SPL (JumpSPL).
Please... any advice will be greatly appreciated.
Similar Problems/Threads:
1. http://http://forum.xda-developers.com/showthread.php?t=406163
2. http://forum.xda-developers.com/showthread.php?t=409272
Try to charge through the usb port on your computer... I have had a similar issue, but that was full stock and still have the issue. HTC chargers wont work for me but select moto ones will. Does the orange light come on when you connect by USB to your computer?
I have tried charging through the USB port on my computer (as well as AC Adapter). It does show the amber light on top (for both methods), but no matter how long I charge it, it will never get to the fully charged green light.
I haven't tried a different (non HTC) charger, but I will try that next.
Are you sure the SIM card door is locked? My phone reboots on its own during start-up if the SIM door is nor properly locked into place...
I just tested the sim card cover. It will reboot at the same point even if the cover is on of off. However, I do believe the cover is sitting correctly, because if I'm at the white AT&T boot screen and remove the cover, the phone will power off.
have you tried hard-resetting your tilt before and after flashing? I had the same problem before. Try to do a hard reset, flash a stock ROM for your tilt, then hard reset afterwards. If same thing happens again, we'll try another method
Put phone in tricolor mode and connect with MTTY.
Type "info 8" and post output here. I suspect problem is caused by bad sectors in the OS area.
There a few different forums on this same subject, and I had the exact same experience on a brand new kaiser last week and thought it was dead. Yea, your gonna have to do a hard reset holding down the power and camera buttons then clicking the soft reset button to get to tri color bootloader mode before it dies, then plug into pc and reflash the official htc rom. It seems like a one time phenomenom as my Kaiser is running just fine now as I was three seconds away from flushing it down the toilet
jockyw2001 said:
Put phone in tricolor mode and connect with MTTY.
Type "info 8" and post output here. I suspect problem is caused by bad sectors in the OS area.
Click to expand...
Click to collapse
Here is the output after using MTTY:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x94C0
Partition[3], type=0x4, start=0xA200, total=0x110C0
CE Total Length(with sector info) = 0x5151000
CE CheckSum Length(without sector info) = 0x5100000
Cmd>
kaalgoosy said:
There a few different forums on this same subject, and I had the exact same experience on a brand new kaiser last week and thought it was dead. Yea, your gonna have to do a hard reset holding down the power and camera buttons then clicking the soft reset button to get to tri color bootloader mode before it dies, then plug into pc and reflash the official htc rom. It seems like a one time phenomenom as my Kaiser is running just fine now as I was three seconds away from flushing it down the toilet
Click to expand...
Click to collapse
I have tried a hard reset before and after flashing the ROM. The method I used was pressing down the two buttons on the front of the phone then soft reset (one above internet button and one above mail button)... then I am prompted with a white screen saying, "This operation will delete all your personal data, and reset all settings to manufacturers default. Press Send to restore manufacturer default, or press other keys to cancel." Please let me know if this method is wrong.
I actually haven't tried the official HTC rom because my phone is originally an AT&T phone. I have tried the official AT&T rom, including the WM6.0 and WM6.1, but I will try the HTC rom now. It won't hurt to try!
UPDATE: After hard reset --> Load official HTC Rom 1.56.405.5 (radio 1.27.12.11) --> hard reset again. Still does the same thing... still rebooting during Windows load. The only difference, no more AT&T screen during bootup... now it's a "smart mobility" message.
jommo said:
I have tried a hard reset before and after flashing the ROM. The method I used was pressing down the two buttons on the front of the phone then soft reset (one above internet button and one above mail button)... then I am prompted with a white screen saying, "This operation will delete all your personal data, and reset all settings to manufacturers default. Press Send to restore manufacturer default, or press other keys to cancel." Please let me know if this method is wrong.
I actually haven't tried the official HTC rom because my phone is originally an AT&T phone. I have tried the official AT&T rom, including the WM6.0 and WM6.1, but I will try the HTC rom now. It won't hurt to try!
UPDATE: After hard reset --> Load official HTC Rom 1.56.405.5 (radio 1.27.12.11) --> hard reset again. Still does the same thing... still rebooting during Windows load. The only difference, no more AT&T screen during bootup... now it's a "smart mobility" message.
Click to expand...
Click to collapse
my OS is writing in bad blocks before that's why it's rebooting over and over again. What I did was use jocky's frankenkaiser (http://forum.xda-developers.com/showthread.php?t=393337). This WIPES OUT ALL DATA IN YOUR KAISER and you need to restore it back again. FOR THIS YOU NEED TO FLASH THE RADIO FROM HELL (get it from here http://forum.xda-developers.com/showthread.php?t=393182) AND AN OLD SPL which you have right now. Read the directions carefully-- it's not that hard but also not for the faint-hearted. Goodluck!
pfcsabre said:
my OS is writing in bad blocks before that's why it's rebooting over and over again. What I did was use jocky's frankenkaiser (http://forum.xda-developers.com/showthread.php?t=393337). This WIPES OUT ALL DATA IN YOUR KAISER and you need to restore it back again. FOR THIS YOU NEED TO FLASH THE RADIO FROM HELL (get it from here http://forum.xda-developers.com/showthread.php?t=393182) AND AN OLD SPL which you have right now. Read the directions carefully-- it's not that hard but also not for the faint-hearted. Goodluck!
Click to expand...
Click to collapse
I know you specifically said to get the radio from hell, but after reading jockey's guide, I got the other radio that GSLEON3 successfully got working with FrankenKaiser. Now I'm stuck because it didn't work out for me. I used radio 1.64.08.21 rather than the actual radio from hell 1.65.17.10. Hopefully GSLEON3 and Jockey will be able to help me with this one.
Can't recall I published FrankenKaiser for radio 1.64.08.21
Here is is:
http://rapidshare.com/files/130939717/FrankenKaiser-V1.9408.zip.html
(follow the readme inside the zip file)
jommo said:
I know you specifically said to get the radio from hell, but after reading jockey's guide, I got the other radio that GSLEON3 successfully got working with FrankenKaiser. Now I'm stuck because it didn't work out for me. I used radio 1.64.08.21 rather than the actual radio from hell 1.65.17.10. Hopefully GSLEON3 and Jockey will be able to help me with this one.
Click to expand...
Click to collapse
ooops... replied to your pm it seems jocky sent you the correct one already. Good luck mate
Losing hope....
Well, I successfully completed the FrankenKaiser process, updated my SPL to reflect:
Security Unlocked
KAIS1*0 MFG
SPL-1.1.JockyW
CPLD-8
I am still getting the power off while Windows loading.
I even tried to load back the original radio from hell (1.65.17.10) and completely ran through the FrankenKaiser process hoping somehow it would fix the problem... but unfortunately, it did not work.
1. Maybe I'll try a few more rom/radio combinations
2. At least I can re-use FrankenKaiser to get back to factory SPL when I attempt to go through the warranty process.
Any other suggestions??? Please let me know.
***Thanks for the help so far Jockey and pfcsabre***
I also have the at&t tilt kaiser version and used the North American Rom update from the HTC website to get it back up. Have you tried getting into tri color bootloader mode by holding the power and camera buttons then clicking the soft reset button then connecting to pc and flash the the official rom? That's what worked for me
also, are you getting any kind of notifications before it shuts down?
kaalgoosy said:
I also have the at&t tilt kaiser version and used the North American Rom update from the HTC website to get it back up. Have you tried getting into tri color bootloader mode by holding the power and camera buttons then clicking the soft reset button then connecting to pc and flash the the official rom? That's what worked for me
Click to expand...
Click to collapse
I have NOT been flashing this way. I have been flashing anytime I get to the tri-color screen, rather than this exact procedure you noted. (Tricolor bootloader--> then soft reset and back to tricolor bootloader) I don't know if this makes a difference or not, but I just tried your method with the rom from the HTC website AT&T Official Rom Download from HTC Website. Still no luck. It still turns off at the Windows screen.
Also, I do not get any kind of notification at all. It always resets before or at the Windows Mobile 6.X screen. I do get a distinctive chime the majority of the time right as it shuts down.
I was having random power down issues as well. This may or may not be the same as your problem, but mine ended up being a hardware issue with the camera itself. My device would suddenly say the camera (actual camera hardware not software) was not recognized and then soon after I would get the chime and then shut down. My only solution was to warranty it. Let's hope I have better luck with a replacement device then a lot of the other storries I have read around here.
Goin' for the warranty...
I want to try the warranty route now. I feel it's hardware at this point because I've already done FrankenKaiser.
Now, my problem lies with returning back to the factory SPL and Rom. I can use FrankenKaiser to UNDO "Security Unlocked" and then use JumpSPL via FrankenKaiser to get back to the factory SPL, but from that point, how do I get back to the original ROM?
Note that I still can't boot into Windows at all, and I will want to flash OEM Rom while I have the OEM SPL. Will the OEM SPL allow flashing back to the OEM Rom, WITHOUT JUMP SPL???
Thanks for your input..
I am posting this here since there seems to be way too many threads around here all saying the same thing diffently yet in NO clear way that everyone can understand. I spent 2 days trying to recoved a Prophet from a bad flash.
Symptoms
Prophet stuck in Bootloaded (Tri Color Screen)
Prophet stuck in 2nd Splash (Usually Your providers Splashcreen)
Solution Read as (This is what I did to fix it)
Download a WM5 Prophet\Wizard Official Rom (I still own a Wizard so I used the K-JAM_WWE_216901_2169101_020710_ship rom, the devices are very similiar concerning chipsets with the hardware keyboard seeming to be the biggest difference)
Extract the Rom (if it is distributed in an exe format with a tool like Winrar or 7zip)
Download the Prophet Tools Light package and extract to any folder . This contains both G3 and G4 RUU's (I can confirm this worked on a G4 Device)
Place the Official nk.nbf in the \Utils\Flash folder
Drop the phone into bootloader (Tri Color Screen) mode and connect to PC via usb.
Allow a few seconds for the usb connection to settle and run the RUU specific to your device.
DO NOT TOUCH the device or PC at this point. If your pc is a tad slow, go make some coffee and watch an episode of Big Bang Theory
This should now give you a shiny new (or old ) rom that is bootable which will allow you to upgrade your Prophet to any of the pretty WM 6.1 roms available.
Just a little tip:
If you are worried about messing up the device again use Alternate "Lazy tool" by dioxda. Its easy and it works !
I couldnt make this process any clearer if I tried
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
specto13 said:
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
Click to expand...
Click to collapse
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
cornelha said:
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
Click to expand...
Click to collapse
Recovery
http://forum.xda-developers.com/showthread.php?t=401326
If at any stage your Prophet fails to start properly or can only enter bootloader follow this:
* Download and install the latest version of ActiveSync (Google for it)
* Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from [here | ftp://xda:[email protected]_NVID.exe] or [here | http://wiki.xda-developers.com/index...=Prophet_ROMs]
* Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
* Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
* Plug the Prophet in via USB
* Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder. If there is only one RUU, use that.
* When it has finished: disconnect the Prophet, and then re-enable the connect through USB in actyivesync before reconnecting the device.
==> if success, will going back into WM5 and then u can use the Lazzy Tool, look at http://forum.xda-developers.com/showthread.php?t=353547
choose WM 6.1 ROM, after u doing that step, u already done with the WM 6.1 SEMOGA SUKSES!
yes it works again ...
Help, please?
Hi guys,
I have a slightly different problem. When I turn on my Prophet, it is in bootloader mode, so I take out the battery, leave for 3 seconds, put the battery back in, turn on the Prohpet.
Bootloader is displayed
Plug into PC with Active Sync 4.5 running (USB disabled)
Windows makes the 'new hardware connected' sound
RUU shows USB in bottom corner
Run the NVID no vender ROM,
Agree to first screen
Agree to second screen
Click Next
Prophet turns off
Windows makes the 'hardware disconnected' sound
Argh
No Prophet, no phone - incommunicado!
When I turn the prophet on now, I just get the bootloader, then it turns itself off after 10 seconds.
Could it be a low battery? - How do I charge it? I have left it plugged in to the power all night!!!
Could it be a faulty phone? - I have been having random resets over the past 3 weeks or so and thought that it was the WM6.1 rom installed, so was trying to put WM5 back on to see if that helps. - I am beginning to think there may be something wrong with the device?
I am trying a few more things from this forum before giving up and buying a new windows smartphone!
Any help would be apreciated!
Regards Mike
Guess it could be a power issue. - I got further just now by using a powered cradle instead of just a usb cable, but still reset at 80% complete. Will leave the phone charging using a wall charger only for an hour and see how i get on with that!
Its Fixed!
Ok,
So it turned out to be a low battery. - I charged the Prophet up for 1 hour and then ran the re-flash and it worked perfectly.
Now I just need to get the Orange rom back on it so its back to normal - Not faffing with WM6.1 - will stick to WM5 as its much quicker and works!
Maybe I was a bit too fast in posting the problem!
Thanks
Mike.
So I recently went to vzw to check if my warranty would cover unresponsive buttons and it does, so they sent me a replacement ozone in the mail. I checked the multicolored screen and saw spl 0.44 and remembered that it couldnt be flashed to hardspl. So I said to myself, "ok, stock windows mobile 6.5 on the ozone can't be so bad" and booted it up. OMG I got used to the 3vo rom sooo much that the phone is crippled with the stock rom. So I want to send the replacement they sent me right back to them and just say f-ck it!! I would rather live with the phone the way it is now.
My question is.... Can I flash a Hardspl to it? has anyone tried and if so did it work. Is there going to be a Hardspl 0.44? Should I try to flash the replacement and if it bricks or fails just send it back? I'm going to send it back anyway if I know I can't install custom roms to it.
Yes, it can be done - apps unlock it first, then flash from 0.44 to .39.hard
Yes, it can be done and I've done it with mine. Read & print out the detailed steps, instructions & review the notes of errors/steps for recovering, etc. - backup your own data/contacts/settings, etc. on the phone - remove the sim card & microSD memory card. I used oem LG usb cable on Windows XPP SP3 desktop & do it without interruption (got a PM story of a ruined flash due to a dog jumping on the link & killed the process, for real ....)
Mine was originally running WM6.1 from VZW, did the HTC official upgrade via the link to WM6.5 and then decided to take a chance with the 3VO flash.
It's very important to do it carefully and get it apps unlocked first.
When that's done successfully & tricolor bootloader confirmed it, pull the battery out for a few moments to reset, and then re-insert & boot it up again before resuming the flash with the unzipped 3VO rom file.
When the HTC ROM Update Utility is finally connected & the phone screen is blank (black) and your pc has finished switching from Moto drivers (ActiveSync) to HTC drivers (re-establish active connections) - and you can see both your "current" version and 3VO version, you are ready to take the plunge & finalize the burn process - took less than 10 minutes at that point.
Then, it's a matter of watching the phone reboot, initialize & preparing the phone for 1st time use and waiting another 5 to 10 minutes, and wow, the 3VO startup & WM6.5 screen will greet you. Then, it's just of customizing the options, restoring the contacts/settings upon putting the sim card (used my owned sim, phone already unlocked) and memory card in the slots.
Good luck.
I tried everything. All directions as closely as possible. I had no errors happen to me on anything and everything flashed as it should have and still no hardspl 0.39. No big deal, I'll just send it back. This phone must be very very locked. Oh well. Thanks for the help.
Where do we find the drivers...after disconnecting. my device comes up as unknown
Good day.......
I am mailing out of real frustration.
I don't know if this is allowed.
I collected a cingular 8125 from a friend in the UK.
I noticed on starting up that there was Tmobile screen first before the windows mobile screen starts. I had no problem with the fone until i realised that i couldnt connect to my local networks GPRS service (who uses a phone that can't browse)
After scanning thru the site, i decided to flash the phone with Crasing's WM6.5 ROM after doing a HardSPL and i could browse and it was the perfect phone apart from the fact that it was real slow and hangs attimes.
It got worse so i got fed up and decided to revert it back to the original ROM and sort the browsing stuff with a network fix that someone on this site had told me.
I reverted the hardSPL and on installing the Tmobile ROM, it brought out an error message, tried with the Cingular ROM same thing.
So i tired reflashing by using a software called Flash Center and it started and stopped at the 1%.
Restarting my phone just shows me the bootloader screen and i have been battling it constantly for 3 weeks but to no avail
I have read almost all forums here, done almost all they ask to do, but nothing.
The only ROM that worked on it is the WIZARD love ROM but it using exactly 21mins to start up. Thot of downloading Faria/Molski WM5 ROM (cos i sorta prefer going back to WM5) but the links for their downloads are dead.
Please help/direct me to where i can see help cos i really need the phone like 2 weeks ago. I am most definitely depressed now.
Thanks.
Check here for all HTC Wizard WM5 OEM shipped ROMS. The one for Cingular is listed in there.
http://forum.xda-developers.com/wiki/index.php?title=HTC_Wizard_Windows_Mobile_5.0_Shipped_ROMs
You say the phone is a Cingular (G4 DOC version). Does it look like this one (click link ... http://www.brighthand.com/assets/4811.jpg ) with the Cingular logo on top left, etc?
Did you require the HardSPL to be able to flash to new ROM, or did you just use the SIM / CID unlocker using the Wizard Service Tool (note the Wizard Service Tool will only work for G3 DOC type device, not the G4 DOC devices)
You said you also removed the HardSPL. If you removed the HardSPL, then you can only flach the OEM ROMS (i.e., if yours is Cingular, then you can only flash the Cingular Stock ROM ... check link above and use Cingular 2.25 (click here ...
... http://www.4shared.com/file/BJUEhCC9/RUU_Wizard_Cingular_8125_WIZCN.html )
First do a battery pull, replace battery, then start device in bootloader mode (i.e., press and hold Camera button on side, then using the stylus press and release Reset button on same side. Do NOT power up the unit by trying to turn on using the Power button on top). Take note of IPL and SPL version that shows up on Bootloader (3 colour) screen. Then plug in USB and try re-flashing with Cingular OEM ROM.
After successful OEM ROM you can then try HardSPL again and re-flash to other ROMS. There are plenty of cooked WM5 and WM6.1 ROMS out there. The WM6.5 is too much (I think) for these devices. A neat clean simple WM5 or WM6.1 with overclocking works very good.
Regarding your settings for ISO, GPRS, WAP etc. you can look for a Netwrok Wizard cab file, and install ( heres the newest I could find ...
http://forum.xda-developers.com/attachment.php?attachmentid=121023&d=1223800573). This will install 6 files into the root Windows directory of the phone. Reboot the phone and you will notice the Network Wizard icon show up in the Settings/Connection control panel.
One of the files it installs is called provision.zip. You will want to update this by copying the following to the windows directory overwriting the old one. This contains all the settings for your phone. Once you copy this over, click on the wizard in the Connection Settings control panel, and it should give you options for Country and Cell Phone carrier/provider. Click away and it shoould automatically set up the correct info for WAP, GPRS, ISP, MMS, etc.
Good Luck. Let me know what happens.
WOW
Thanks for the response
I used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
WOW
Thanks for the response
About the pix you reffered to? Yes thats exactly how my phone looks like
I had used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001, SPL 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
PS: My IPL/SPL is 2.26.0001
OK. Good info.
Not sure how you did it but somehow you managed to get the T-Mobile IPL/SPL on it, and yet it still recognizes it is Cingular. For one reason or another one aspect does not let the other load and vice versa. ????? Hhhmmmnnn ????
Here is what I would try.
1) I have attached a zip file called SoftSPL. Inside I have made an image file nk.nbf, which contains ONLY the 2.25.0001 IPL and SPL for the Cingular 8125.
Unzip this folder to your Desktop and then try to run only the "newromupdateutility_wizard_noid.exe". Remember, start the phone up in bootloader mode, connect via USB then run the "newrom...exe" file. If you get an error right away saying this is not the right update utility for the phone or something like that, then start over ... i.e., disconnect phone, pull battery, start phone in bootloader mode,reconnect via USB, but this second time try using the one called "2.exe". I found sometimes when I flashed ROMS the first one did not work and the second one (2.exe) did for me.
IF this works, once you get the 2.25.0001 IPL and SPL showing on the bootloader screen then start again (pull battery etc. same as above) but then re-flash back to the original Cingular OEM 2.25 ROM that you tried earlier (the original RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe). Try this and let me know how it goes.
If and when you get it back to the original Cingular ROM, if you get to this point, you can then start back like it was when phone was "new". It will still be SIM unlocked so you can use any carriers SIM card but you cannot flash other ROMs.
If you are going to try other ROMs, re-apply the HardSPL, but make sure you only use ROMs that have been cooked, say they are safe for G4 devices and do not have IPL/SPL in them. This means when you have it HardSPL'd you cannot, or should not use other carriers OEM ROM's such as T-Mobile 2.26 or 3.08.
Lastly, if you do like some of the "extra's" offered with WM6 or higher and do not like a slow phone and want to keep it fast like a WM5 ROM, then stick to either WM6.0 or WM6.1, clean (or what they call Vanilla) ROMs.
Good Luck. Give feedback of how it works out for you and pay attention to errors and messages and IPL/SPL etc. for reporting back and I can help you a little more.
Another thanks again.
I really owe you if and when my phone is finally done cos i think i am getting there.
But i successfully changed the IPL/SPL but on flashing the cingular ROM it says the RUU cannot see my phone and once it sees that it says the update utility cannot be used for my phone.
So what next?
Maybe the ROM is not the right one but i ensure it was meant for g4 tho"
Tried MUN-RUU but to no avail
Eagerly waiting your reply.
Thanks again
OK. YES. You are getting there.
You say the phone is now IPL/SPL 2.25.0001. It shows this on the 3 colour bootloader screen?
What did you run in order to flash; did you run the "newromupdateutility_wizard.exe", or "2.exe", or did you need to run the "START-sSPL.exe" to flash th nk.nbf file I made? (I don't think the "START-sSPL.exe" works from the bootloader screen...phone has to be booted to working status).
Here's what is next. I made a new nk.nbf which is the Cingular 2.25 OS, splash screens and 2.25 radio only. I removed the IPL/SPL and the Extended_ROM, and cooked this back to nk.nbf.
Download it from here .....
http://www.fileswap.com/dl/7WhstX82/nk.nbf.html
..... and copy this to the folder you made of the SoftSPL earlier (overwriting the other nk.nbf - you may want to save that as a back up)
Now try flashing this new nk.nbf again as you did for the IPL/SPL.
If it works, then let the phone boot up completely. Check it out. And then you can run the RUU for the original Cingular OEM once the phone is booted to get it back to Cingular OEM state (full IPL/SPL, OS, GSM, Extended_ROM, etc.)
From here (if you make it) then any further flashing of ROMs, you will want to flash G4 safe ROM's, and you can do this using the SoftSPL folder. Copy the nk.nbf from the custom ROM you want to flash into the SoftSPL folder and run the "START-sSPL.exe" with your phone connected (not in bootloader mode, has to be completely started up and recognized by ActiveSync, but you do not need to establish partnership ... just skip/cancel that part and phone will connect to ActiveSync as a "Guest").
Good Luck. Let me know how you make out with this.
Just to answer your questions.
I ran the "newromupdateutility_wizard.exe"
Would follow thy new instruction sire and get back to thee.....lol
Thanks again.
I am not here to say "Yipee, its done'
But rather to say that the universe, cingular and the god of communication might have just conspired against me.
Just when i think i would finally get my phone working after 3 weeks, a 2 yr old kid took my batteries and only God know where that batteries is now.
Tried to buy a new one but all i get is "Wow! that a pretty old uncommon phone here"
I intend to use an ac to dc converter and when i am done i would give you the feedback
Thanks
PS: Just wanted to give you the heads-up
So i found the battery early this a.m.
Flashed the phone with the ROM you uploaded and it was succesful but on starting it i get a green screen and its damn slow and doesn't even pass the spot where you are asked to align screen (i really do think that nothing happen and its still the Wizard Love ROM that its still booting into)
So I am still stuck?
Hmmm....
OK i guess there might be a psych diagnosis for what i am doing (posting excessive replies without any respond)
It just a worried person.
So i kept re-trying to flash the ROM on my phone about 2ce.
Then i noticed on the 2nd time at about 86% the phone seemed to restart itself into bootloader mode about 2-3X, so i thot the battery was running out. Decided to take it out and get it charged.
On plugging the battery back to the phone all i got was a white screen and starting it on bootloader mode OR hard-resetting still gives me that white screen. On removing the battery the phone flashes like once or twice.
Is this the end? The phone has brought an apocalypse on?
Been doing a lot of browsing for clues but nothing tangible yet.
God smiled on me and the phone started
Got the ROM you gave me flashed and its really refreshing to see the Windows Mobile logo again
But i am stuck at the align screen tho'
I tap and nothing happens unless i drag the target and it just moves around and get back to the original spot.
Thats the latest pal.
OOPS. I did not read all .... your posts ... I just answered your post at the end of the last page. Did not see these last 2.
This is a good sign that you get past the initial boot splash screens and make it to the Align Screen ... soft reset the phone again and look at the IPL SPL that shows on the screen. Is it 2.25.0001 or 2.26.0001?
If 2.25.0001 then let the phone boot up to the Align Screen (and if you cannot get past this then just leave it at this point). Plug back into computer and now try to flash Cingular OEM ROM 2.25 that you tried earlier using the stock file.
If this doesn't let you flash for the same reasons as before (i.e., Invalid RUU tool or Not correct operator) then extract the nk.nbf from the Stock Cingular ROM (right click on the Cingular RUU OEM exe and select "Extract here ...".) then copy the nk.nbf over to the Soft SPL folder and use the START-sSPL.exe and flash this way. (you can delete the rest of the files from the Extract process.
Good Luck. Let me know the IPL SPL you get.
I know my posts are getting sickening but i am really desperate.
Got some info about how to bypass the align screen online but couldn't get my phone to boot anymore.
Soft reset/Hard reset/Bootloader mode: All of it just shows a white screen and nothin more.
Any ideas?
PS:The last time i could start the phone the IPL/SPL was 2.25.0001.
Just want to add this cos i just noticed it:
1. Sometimes tapping the Camera button alone puts the phone on (tho' it shows that annoying white screen)
2. On connecting the phone to a PC the PC recognises it even tho' its off and once i put it on and that annoying white screen comes on, the PC gives the same sound as when a USB is detached.
Hope these info would help.
I"m really getting depressed now. Hope's looking dimmer.
OK. I am now suspecting that you may also have a battery problem. How old is the battery. Could be the battery no longer has enough capacity. It may charge but only hold a charge for very short time and voltage may be too low. Maybe enough power to keep some of the electronics "awake" but not enough to drive the LCD.
It is now IPL/SPL 2.25.0001 so it should be able to flash the Cingular OEM ROM. You may want to try a different battery. Other than this, if not a problem with the battery then I think maybe phone itself is coming to an end.
I would try the battery route, making sure you have a good power source, and then try to flash the stock Cingular ROM.
You can still get these batteries on ebay and phone as well. If you are going to spend any money then maybe instead consider a newer model phone on ebay. (if you are patient you can find very good deal ... I got the T-Mo MDA Vario version of the Wizard (WIZA200) for $25 plus shipping, brand new with a carrying case. It was an estate item from a salesman who passed away and phone was not used before he passed on. One man's misfortune, another man's luck. I am now selling this on ebay plus memory card and earphone here ... http://bit.ly/hDHxrW. I have two more on sale at ebay here... http://bit.ly/eV0zZh ... and here ... http://bit.ly/gLIiKh. I am selling 3 and I have upgraded to Touch Pro 2. Go with AT&T version as this can beused world wide on 3G in North America and is quad band GSM for use in rest of world)
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
Cheap battery on ebay ..
http://cgi.ebay.ca/New-Li-ion-Batte...652056?pt=PDA_Accessories&hash=item5d2d297c58
http://cgi.ebay.ca/Battery-HTC-Wiza...163910?pt=PDA_Accessories&hash=item45f7ebb846
Phone
Wizards
http://cgi.ebay.ca/HTC-MDA-Mobile-S...0528835033?pt=Cell_Phones&hash=item4cf50dc5d9