Database Info

dead or alive

My jam is stuck on the serial screen
tried upgrading with imate original, wont see the phone
tried mtty d2s (from a working unit)>NTRW READ FROM sd, ntrw WRITE TO SD, it freezes on boot,
the mtty intracts with the phone: here :
USB>info 0
MAGICIAN
USB>info 1
1.00
USB>rtask 0
Radio reset.
USB>checksum
CRC checksum=0xACC883CE
no luck restoring the backup file,
any clues ?
thanks.

ok seems i have a shot bootloader, when i try d2s, the screen goes blank.
s2d dows not work with jam
rbmc is locked!
erase is locked
password >> need a password to do much of the writing commands
lnb >>not allow operation
in short, there is no way(from where i stand) to flash this thing, attempting to flash with SD returns a frozen set, same SD was able to flash another unit.
any clues ?????

I now have the same prob...
I wanted to flash the: ma_cdlsku12_wwe_10300_163_10100_ship.exe
but it now is stuck in serial mode...

pc->drive.total_lba=77380
pc->drive.num_heads=8
pc->drive.sec_p_track=20
pc->drive.num_cylinders=773
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=A95C
pc->drive.drv_type=0
pc->drive.securedAreaSize=1500
pc->drive.securityDrv=5
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=EE70000
SDCARDD2S+,cStoragePlatformType=FF

My probs started after flashing the UK ROM of the I-mate in to my MDA Compact.
MTTY:
USB>info 0
MAGICIAN
USB>info 1
1.00
USB>rtask 0
Radio reset.
USB>checksum
CRC checksum=0x68A159CD
I can't flash my MDA compact Backup ...
What could be the sollution?!!

can you do d2s from mtty ? if so, you are in luck, you can still revive your set. if not, try the warranty option something i do not have.
Try d2s, if it works, stop, download the backup from the xda ftp, use ntrw to write it to SD, then put your set in boatloader mode with the SD in, wait 7~10 seconds, it will ask you to press power to flash, & you are there.
if you cannot perform a d2s, your screen goes blank when you try, i do not have a solution, nor does anyone else, so far... either wait, OR try the service center.
regards.

You were right, MTTY is still working. I finally got it working again. It took me several methodes.
I got it in serial mode after flashing it with this ROM (it couldn't get out serial mode) --> http://www.cddnet.com/Support/ma_cdlsku12_wwe_10300_163_10100_ship.exe
The backup i made didn't work. But an other way worked:
The other ROM's didn't work but by first updating the radio file form this ROM --> http://www.clubimate.com/Support/ma_cdlsku1_wwe_10300_143_10100_ship.exe
and then doing the setup complete (ms, nb and radio) it finally worked!!

i have the same problem when i tried to upgrade.
now im stucked with the serial screen, and youre method doesnt work for me, it says unsupported format when i dubble click at radio_.nbf
and when i run a full upgrade it says Modell ID error.
hope someone can help me

Palm Treo 750, stuck in bootloader ROM flashing not working

I had to hard reset my palm, as it was stuck at windows screen. It had WM6.
Now it does not go beyond bootloader screen.
Tried, the following
1. Palm recovery tool, connection gets lost
2. Tried ROM flashing with the WM6 ROM (CHEEIMG.nbh) with 2GB Mini SD card with FAT 32 formatting, does not progress, it gets stuck no progress even after one hour.
Not sure what to do next, any help is greatly appreciated.

Hi mohaninusa2003, looks like your waiting for a reply since a while. Here you will find all the answers connected to your issue. Probably you did already but just incase have the link
http://forum.xda-developers.com/showthread.php?t=366771

Thanks hammod2k, I have tried all the suggestions on the thread. Still when flashing the original rom, it does not go beyond Bootloader -ok hans at GSM, left overnight for flashing, still not working.
Tried Mtty, set 14 0/ task 28 55aa /
Tried to flash Hard SPL, bit it is not successful, I am getting an error "Image file is corrupted".
I will keep searching threads and reading..in the meantime.

recovery tool
my friend where i can find the recovery tool? i been looking for it but nothing even on the palm suuport page? thanks in advance
regards from lima
mohaninusa2003 said:
I had to hard reset my palm, as it was stuck at windows screen. It had WM6.
Now it does not go beyond bootloader screen.
Tried, the following
1. Palm recovery tool, connection gets lost
2. Tried ROM flashing with the WM6 ROM (CHEEIMG.nbh) with 2GB Mini SD card with FAT 32 formatting, does not progress, it gets stuck no progress even after one hour.
Not sure what to do next, any help is greatly appreciated.
Click to expand...
Click to collapse

stuck on boot loader
hey mohaninusa2003..
I exactly have the same problem bro..it hangs up on gsm...i tried removing my card and hard resetting it but it just brings me to a tricolored screen red green and blue with the word serial at the bottom...tried soft reset but still the same thing..hope someone could help us on this

Hey fguimet,
Please follow the link and look at post 9 for the file,use the Desptop update method file and extract using winrar to get th file you are looking for. hope it helps,
http://forum.xda-developers.com/showthread.php?p=1714416

Sorry to bother but i have a few questions...i have a 750 treo and none of the support on this website is helping...i am trying to flash my palm 750 but its says the file is corrupted..what do i do about that? Progress only reaches 7% ive used cheetah and kaiser unlockers and i was also wondering if it can be flashed just using the computer and usb in booter mode since it wont go past the palm splash screen...i can access my treo using mtty but doing task 2a doesnt do anything either... I think that maybe my phone is screwed up. I appreciate any help you can offer.

I have almost the same problem with my Palm 750 that I believe locked to Rogers.
1. It hangs on GSM if I use SD card ROM file CHEEIMG.nbh . I have tried many different CHEEIMG.nbh files (ATT, Cingular, ROW…)
2. Running CheetahUnlocker will crush at 7%, and my Palm 750 will reboot and freeze at MS Mobile screen.

I have the same problem, and I think we have to change the IPL and after run cheatunlock.
How can we do it?

on my treo I have hard-spl'd but still i cant manage to flash a rom
My Bootloader screen results:
CHEE100
IPL - 0.20
CHEE100
SPL - 1.40.0liNex
______________________
it starts, gets to about 4-7% and then it says:
|00018003
|CHEEIMG.nbh - FAIL
|
|OS - Fail
|
|
|
|Update Terminate
|UPDATE FAIL
i have no idea what i am doing wrong
it all started when i tried to flash a wm 6.5 os and it didnt work... i was just randomly stuck on the bootloader screen
Swarford

Stuck en bootloader

Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)

Please need some help ( a lot)

beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and

Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??

beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+

too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark

Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull

dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?

noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.

back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...

ok, will send the s200 to the SAT (repair). I don´t have other options.

My Treo 750 wont upgrade

Hello. I had a Treo 750 with the original os. After finding out the windows mobile 6.5 version that you guys had i tried it and it worked.
Well.. i saw another one that i thought was cooler... htc like and tried it on, i have installed using usb method and the installation went well. After I rebooted I got a 3 coloured screen.
Ever since that i have tried every method i could found, i tried flashing rom using mtty command
set 14 0
task 28
tas 0
than I installed the 6.5 version using my sd card. It all goes well untill at some point I get this on the screen:
CHEEIMG.nbh
SPLASH1 - OK
BOOTLOADER - OK
GSM - OK
MicroP - OK
EXTROM - OK
OS - Fail
Update Terminate
UPDATE FAIL
Any other CHEEIMG.nbh file i try i get the same error -.-
In some topic I saw that in this case I had to flash using the original rom, I have a Cingular device from the US (im not in the us), was a ATT rom that I have seen posted in the forum.
If I update this 6.5 CHEEIMG.nbh using the complete fix kit through usb it stops everytime in different percentages. It got stuck on 12% , 53% and others but never finishes..
I have also tried the original rom through cable mode using complete fix kit and it sais the CHEEIMG.nbh file is corrupted ...
Im about to loose my patience since i've been on this for days... can anyone give me a hand?
By The way Merry Chrystmas to you all

stuck on bootloader

i was installing kotas ver "c" rom. during process my pc suddenly shut down and after restart i am not able to recover the process and my polaris stuk or hang at boot loader skin. during the process i forget to remove the memory card. previously i was using "M. Amine 2.0" rom. i also tried the matty but unsuccessful, when i select usb it gives an error "can't read from usb".
help guys???

If you see the bootloader you can still flash a rom try another one or another method maybe with SD flash

i successfully resolved the problem. when i take my poris to HTC center they ask me change the motherboard, thanx to imfloflo for suggesting me that i can still flash it with SD. And special thanx to taiseer999 for the post of "How to flash your Polaris using the microSD card [Guide]" and Whitealin for "[SOLVED] Connection Error [262]. Stuck in bootloader (tri color) mode. ". I am really thankfull to you guys. You guys are grate.