I have the BT800 and I have gotten some results but I want more people to try it,,, maybe with the Sony-Ericson devices. (I am not sure if the Caller ID and call list works with the Sony-ericson BT headset.. So, if you know it works, let me know.)
The BT800 needs BT stack 1.1 or 1.2 and Handsfree Profile to work.
I do not know what MS BT stack I am running, but, with the below handsfree reg hack, I got it to work.
Get rosco file explorer, (serial available from astalavista.box.sk , or use trial version). add the registry entry of Hkey_local_machine\software\microsoft\bluetooth add a new key while "bluetooth" is highlighted of "HandsfreeProfileOn"
Delete the pair on the BT800 and your PPC and turn them both off.
Turn back on the PPC and the BT800, Repair the device and the BT800, go to BT manager, click and hold on the BT800, select Handsfree.
Let me know how this worked, I have had mixed results. One time it did get caller ID and all worked well, but then only the audio was being played to the BT800 and the phone was also playing the audio and the mic did not work on the BT800, only on the phone.. BUT, this may only be my device for I have messed with it so dam much.
After the lot of trials I made with Jetware several releases, I found that this one solved it realy. It reads from phonebook not SIM contacts. It shows the name and save it as a name in the calllist, however this blocked calling from calling list on your Headset.
The example below as made by our colleague Dtread1 I just copied it from Athena accessories, is showing jus the BT 8010 and the advantage, The Jetware is giving solution almost for all. The BT 8010 was not on the list of devices but using the NOkia one worked fine.
Jabra BT 8010 - Solution to display Caller ID
--------------------------------------------------------------------------------
As the first instructions caused some confusion, and some people couldn’t get Jabra to show caller ID, hear are them more complete.
Don’t forget that caller ID only “works” if the caller is in your contact list in the HTC X7500.
A problem still remains: Dialling from Call List in BT8010 doesn’t work
1 – Delete the paring between HTC X7500 and Jabra (if you have one).
2 - Upgrade the Jabra to V1.33 . (http://uswww03.gnnetcom.com/Myjabra/... enter_na.html)
3 – Install Jetware V1.30 on your HTC X7500 (http://www.jetwaremobile.com/)
4 – Soft reset Your HTC X7500
5 – On your HTC X7500, go to -> Start -> Programs -> Bluetooth Options -> Hands-Free Config ->
Menu -> Advanced options -> Ok. Here, at least, you must select /check this options:
.Phonebooks
.Messaging
.Caller ID
.Query status indicator
.Update status indicators
.Hang up/swap to incoming call
6 – Establish a new paring.
7 – On your Jabra settings select -> Display -> Caller ID and select -> ON
8 - From your Advantage (connected to ActiveSync or GPRS) go to this link (http://www.jetwaremobile.com/bthfx/D...kia_HS-12W.jcf.)
9 - When you download that file you should get a prompt asking which paired Bluetooth device the settings should apply to
Choose -> Jabra and -> Done.
10 – Soft reset your HTC X7500.
11 – Turn off your Jabra.
12 - Turn on your Jabra
Regards
__________________
AM
Hi!! I have some problem with my vox + HBH-DS970 headset. I can't redirect incoming call sound from phone to headset
With my previous phone i change "capability" parameter (4-th bit by 0, like 110101)
But "capability" parameter in Vox is 7 bits lenght!
I'll try to set 1110101 (117) and 110101 (53), but it doesn't work!
while incoming call, i hear phone but not headset
Anyone can help me with advice?
bt headset prob
I have an xda2 i and I have the problem that even when the headet is connected, at times an incoming call won't broadcast over the headset at all, and equally if i dial out the call doesn't transfer to the headset.
Curiously, I've found the solution is to go into bluetooth manager -->active connections--> and click on STATUS of the head set connected. it should show signal strength and such. I double click on the CONNECTED message (oor maybe somewhere on the screen, basically double tap until it reads NOT CONNECTED ..... as odd as it sounds... this is what i needed... as when I do this, it usually works ok for me.
Maybe it will help?
..........IB a n e
this is smart, so there is no any bluetooth manager on it
and my headset can play any sound from phone because it is A2DP and i'm continuosly use it
i have one way to solve this - JetWare BT-Extension. In this programm i can check "use phone ringtones" and that works OK
but program unstable, so i want to get this future by regisrty edit
Hi all,
I am trying to use the factory bluetooth integration in my car, and from everything I've read, it requires SAP (or rSAP?) to work properly. I've never had trouble pairing to the bluetooth module, but the car still insists there is no phone.
After messing with it yesterday and installing SAPSettings, I can hear the speaker of the phone in the car's audio, but no microphone, and it still says "insert phone" in the car's phone menu as apposed to downloading the phone book and letting me dial on the screen.
The phone lists the SAP profile among many others, but if I go into the settings of the car's bluetooth connection, it only lets me choose "Hands Free", with an on/off checkbox. It seems like thats what it sensed was available from the car, and offers nothing else, but I'd like to force SAP instead.
Car: MB E-Class
Phone: Sprint HTC Touch
OS: WM 6.5
Thanks!
I'm going to put the official windows mobile 6.1 on it to see if it makes a difference.
bluetooth is a long list of various profiles
problem is that devices only need to implement 1 or 2 to call themselves
bluetooth devices and no if the maker of the bluetooth stack in both ends
didn't implement a profile you can't force it
I have this problem trying to get my HD to connect to my landrover freelander 2 hse. I can get it to connect to the phone, but cant get the call to play thru cars speakers.
Dont bother with winmo 6.1 or official rom, just doesnt work at then (cant connect).
Only way i can get it to work is with winmo 6.5 (manila 2.5) (profiles must have newer or more stable settings). Only thing i have to do then is to make a call (normally voicemail) turn privacy on, then off again and voila it plays thru speakers.
Downside is i have to do this everytime i start the engine.........
Now that probably doesnt help you much but you will probably find from your car manufacturer that you device is not supported with you cars handsfree bluetooth kit.
the only one fully compatible with the freelander 2 is................. an phone
Hello, I am quite an avid reader on xda and have gained a lot of knowledge from this forum. Unfortunately I have run into a problem I cannot seem to understand.
I have a Samsung Omnia 7 (T-Mobile, flashed a stock omnia 7 rom,unbranded). Whenever I pair it with my Car audio (I have a Suzuki Alto) the audio drops atleast 5 times a second.
Also the mic voice quality is terrible (people on the other end complain of a lot of static & as if i were speaking from a thousand miles away).
I also happen to have a developer unlock on my phone so this gives me easy access to the xaps.
My Samsung Omnia 7 details are :
OS Version : 7.10.7740.16
Firmware Revision Number : 2424.11.9.2
Hardware Revision Number : 3.15.0.4
Radio Software Version : 2424.11.9.1
Radio Hardware Version : 0.0.0.800
Bootloader Version : 5.9.0.6
Chip SOC Version : 0.36.2.0
I read on the forum about using the Advanced Config tool to set the Bitpool to 51 and set Joint Stereo to 1. But whenever I tried doing that a popup would say "Unable to apply changes"
So I navigated to HKLM\SOFTWARE\MICROSOFT\BLUTETOOTH\A2DP
and I saw ONLY ONE subkey that as Devices that had 4 Subkeys labelled 1,2,3,4 each with a binary value (Address)
I added a key Settings to HKLM\SOFTWARE\MICROSOFT\BLUTETOOTH\A2DP and I added the following values to it:
Bitpool : 51 Dword
MaxSupportedBitpool : 51 Dword
SampleRate : 48000 (this was added by advanced config later when I was trying it out again)
UseJointStereo : 1
I tried testing these settings with my car bluetooth kit but the results were the same. At first I was baffled when I didn't see the key SETTINGS in the HKLM\SOFTWARE\MICROSOFT\BLUTETOOTH\A2DP path.
Is this normal?
Is there any way to fix the choppy extremely low quality bluetooth audio?
(PS I do not want bluetooth over video, also I have set SupportCLI from 0 to 1)
Hi,
Got the same problem.
BT worked in the really early days of my Omnia but since then, I am unable to listen to music on my Motorola S9 headset (even worst than you ! Drops 10 times a second !). Even the call quality when using a mono BT earpiece, sound is distorded and other side does not understand a thing of what I say !!
Sad to say but I really think Omnia 7 are subject to Bluetooth hardware failure.
Really think there is no way and quiet forgot about using BT on my handset. Shame because I was using my S9 all the time with my previous wm device and it was really working very well.
Anyway, if you figure out what's wrong, please, share with me ;-)
Last thing, did you apply some audio tricks through the Samsung diagnosis app ?
Good luck
Thomas
Sent from my OMNIA7 using Board Express
Hi, thanks for replying, I don't think the omnia 7 is subject to BT hardware failures as i've read about several omnia 7s running okay.
Also I did apply the sound trick using the diagnosis app but it messed up the audio on my phone. 30/30 sounded like the speaker is going to explode. Though the changes used to fall back upon restarting, they would come back if I played a song or if I got a call. So I had to re-flash my rom & reupdate it to mango.
I haven't tried BT on any pre-mango version but I guess its going to be the same.
Anyways lets hope Microsoft comes out with a fix in their tango update in Q2
:fingerscrossed:
Really wonder if BT problem may be linked to the sound trick. May sound weird but as I said, Bluetooth was working flawlessly at the beginning and I'm not 100% sure but it may have stopped working the day I messed with Samsung diag on sound settings.
More than that, I wonder at which OS level these settings are managed (even wondering if a hard reset or ROM flashing can roll back the whole thing to the factory settings)
I hesitated to hard reset in hope it will work again but I do not want to lose everything without being sure problem will be solved (and will never know id I don't do it )
Thomas
Sent from my OMNIA7 using Board Express
In my opinion the settings are rooted in the rom, you cannot program the hardware from the rom but only change the settings (this is what i think) anyhow, my BT settings never worked, not before messing with the audio settings in the diagnosis, not after, also what's weird is that the a2dp settings weren't present in the registry, i had to add bitpool, maxbitpool etc. manually (no change even then)
anyways, lets hope someone knows of a workaround or microsoft regards this issue as 'serious'
thanks
EDIT : @NebZoNe I tried your settings and they didn't work for me thanks for the suggestions anyways
adding a registry entry for bluetooth like bitpool should be made in ..\AD2P\Settings
see http://forum.xda-developers.com/showthread.php?t=1351043
try a registry editor instead of schaps' advanced config...better.
max supported bitpool must be 80 (dword)
if you use 51 for bitpool then you can't use jointstereo (set it to 0), or use 53 then you will be able to set 1 for jointstereo...
once you've connected your car's stereo to your device try to find the second tweak i've written (dots between \ are numbers) to make sure the sound will be streamed in stereo (if you setted bitpool at 51 for sure!)
good luck.
Hello, I used the root tools by cliff74 & advanced config to verify the settings. Anyways, I haven't tried bitpool at 53 & will do.
Question : in your post you have said this :
HKLM\Software\Microsoft\Bluetooth\Device\........\ Services\..........(then u should see u're in stereo sound settings)
enabled : Dword = 1
The dots are the numbers, so how do I know what device is which number?
Thanks!
japmeet said:
Hello, I used the root tools by cliff74 & advanced config to verify the settings. Anyways, I haven't tried bitpool at 53 & will do.
Question : in your post you have said this :
HKLM\Software\Microsoft\Bluetooth\Device\........\ Services\..........(then u should see u're in stereo sound settings)
enabled : Dword = 1
The dots are the numbers, so how do I know what device is which number?
Thanks!
Click to expand...
Click to collapse
Do you use so many BT devices that you can't identify them in that path?? i only use bt headphones so i didn't have that kind of problem sorry...
and i'm agree that what you'll find behind \Device\ is straightly linked with what you use...so you must find the string "stereo sound" for every device you connect...as well as you'll find a string value with your bt device name after first connection....
I must insist on the fact that schaps advanced config is screwing with BT's manual reg.edition...and there's no reg lines for samplerate values, they are setted up straight from bitpool level (51:48000; 53:44100; 76:96000)
unfortunately, having a look to other threads, it seems that samsung devices usually know issues with bluetooth function...
well in HKLM\SOFTWARE\Microsoft\A2DP\Devices I have 4 subkeys that are :1 ,2,3,4 each with 0 subkeys and 1 value that is address (a binary value)
In HKLM\SOFTWARE\Microsoft\Bluetooth\Device I have 1 subkey that is 00137b96be74 that has 1 subkey "Services" which has 2 subkeys :
The first subkey has the following contents :
Status (a subkey that is empty)
channel (value : 0 dword)
enabled (value :1 dword)
name (stereo sound)
sdprecord (binary value)
Similarly the other subkey of \Device\ has the same contents except for channel and name
Channel (1)
name (Hands-Free //I suppose this is my car bt audio but when i sync my phone with the car it shows BT Radio as the car's head unit's name)
Also i have logitech free pulse BT headsets and I have the same problem with that
well, seems that's alright i've got the same layout...
the only thing i can do is sharing my ad2p settings layout...
hope for you it's not a hardware issue...
I do not have the default key (not sure if that would make any difference) but anyway, thank you
japmeet said:
I do not have the default key (not sure if that would make any difference) but anyway, thank you
Click to expand...
Click to collapse
Same situation with my omnia 7 - and i have motorola s9 like you. I tried many settings in registry but all of them have absolutely no effect ((
though I shouldn't be bumping but *help?*
As I already told, sorry but I really think the reason is really simple. BT chip on Omnia 7 is defective, this is a hardware failure and I am quiet sure it can not be software solved.
There are plenty of reports on the web with people having the same problem with Omnia 7 :-(
Sent from my OMNIA7 using Board Express
But my motorola s9 worked fine with NODO.
Can we diagnose somehow that it is hardware issue? I have used following codes in Diagnosis:
*#232331# - BT RF Test Mode
*#232332# - BT Audio
*#232333# - BT Search Test
*#232337# - Bluetooth MAC Address
First one tells me that RF testmode is on, second gives me nothing... Third displays Search Failed!!! message and fourth just same code...
On my omnia
*#232331# - RF Test Mode ON!
*#232332# - Nothing
*#232333# - Search Fail!!!
*#232337# - 0x78471D364188
My bluetooth only works well when I put off the wifi on my Omnia 7
Sent from my OMNIA7 using Board Express
I've tried the codes and I have the same results as you have, sigh.
ikke008 said:
My bluetooth only works well when I put off the wifi on my Omnia 7
Click to expand...
Click to collapse
My bluetooth dont work with wifi.
And without wifi sound is choppy.