Hi!! I have some problem with my vox + HBH-DS970 headset. I can't redirect incoming call sound from phone to headset
With my previous phone i change "capability" parameter (4-th bit by 0, like 110101)
But "capability" parameter in Vox is 7 bits lenght!
I'll try to set 1110101 (117) and 110101 (53), but it doesn't work!
while incoming call, i hear phone but not headset
Anyone can help me with advice?
bt headset prob
I have an xda2 i and I have the problem that even when the headet is connected, at times an incoming call won't broadcast over the headset at all, and equally if i dial out the call doesn't transfer to the headset.
Curiously, I've found the solution is to go into bluetooth manager -->active connections--> and click on STATUS of the head set connected. it should show signal strength and such. I double click on the CONNECTED message (oor maybe somewhere on the screen, basically double tap until it reads NOT CONNECTED ..... as odd as it sounds... this is what i needed... as when I do this, it usually works ok for me.
Maybe it will help?
..........IB a n e
this is smart, so there is no any bluetooth manager on it
and my headset can play any sound from phone because it is A2DP and i'm continuosly use it
i have one way to solve this - JetWare BT-Extension. In this programm i can check "use phone ringtones" and that works OK
but program unstable, so i want to get this future by regisrty edit
Related
Ok, I have a BT200 that is working very quirkly with my i-mate. Sometimes the phone transfers the call to the headset, sometimes it doesn't. After deleting and recreating the bond, it works, but not for long. Anyone have one of these setup and working properly? Is there a trick to it?
Also, does anyone know if other headset drivers exist that may work on the i-mate that would allow you to hear all audio (not just phone) through a bluetooth earpiece?
Figured it out?
Ok, I've finally pinpointed that it works fine until I turn off the jabra headset, then when I turn it back on, I have to go through the entire thing again of re-creating the bond, etc..
Anyone know how to avoid having to recreate this everytime I turn the headset on or off?
I don't now ... but i have also jaba 200 and the MDA II is must arrive...
well please chip us informed
Thanks
DenisJ
I have the same combination and have also observed the same hassles.
It seems to work when I turn the BT headset function on the MDA off and on also. Thsi seems to result in a rebond.
Exact Steps
TBD,
If you could post the exact order of the steps you take to turn on / off the headset, I'd appreciate it. Right now, I'm doing the following:
1. Finish BT Headset Call.
2. Disable Bluetooth Headset Mode on Phone.
3. Disable Bluetooth on the phone.
4. Hold button on JABRA to turn it off.
Then, attempting to...
1. Hold button on JABRA to turn it on.
2. Enable Bluetooth on the phone (Set to "On" or "Discoverable")
3. Enable Bluetooth Headset Mode on phone.
4. Attempt to make call.
So if you could posts steps like that, i'd appreciate it. Also, do you set your bluetooth to "On" or "Discoverable"? Do you ever turn off the Bluetooth Radio completely?
Thanks,
Jon.
Yup me an all. I too have the Jabra BT200 and have the same problem. Providing you don't switch off the headset or go out of range your ok, but for instance when you leave the headset in the car and take the XDA2 with you you have to create a new bond to use it again. AHHHHHHHHH!!!
Shame cos so much else has been sorted on it.....and more. What a piece of kit!!
SOMEBODY HELP!!!
OK, so here is the sequence, which seems to work (for me).
1) I set everything up as per instruction. creating the bond between the Jabra and the MDA II.
2) Before (or after) I turn off the Jabra I disable the BT-Headset on the Today-screen.
3) Then I turn the Jabra on again and wait several seconds before enabling the BT Headset on the MDA II.
This seems to work most of the time, though the hint regarding going out of distance might explain the instabilities I have still observed. In any case, using the BT-Headset ON/Off on the Today-screen seems to resync things most of the time and get the Jabra up and running again.
Hope this helps and always open for new ideas
I have been a bit impatient after turning the BT headset on. I'll try it and let you guys know.
I may have been a bit optomistic. :roll:
Today I observed that sometimes the Headset reacts very late. Consequently you miss half of the call. Seems to be an XDA problem.
As for my XDA II with Sony Ericsson HBH-65, after creating the bond, before i turn off the BT headset, i turn off BT profile and BT on my PDA, then turn off the Headset.
If i want to turn on the headset, i activate BT on my PDA, then BT profile, the the headset. Sometimes in teh day headset seem to lose the bond and cannot use the BT to call or whatever. I tried turning on/off BT on my PDA, did not work. Turn on/off headset, it worked. So for me most of the time is my headset causing the problems
i am having the same problem with the new moto bluetooth headset although i have experienced no problemzs with the se hbh-30 bluetooth headset....i can turn off and transfer calls without any impact on teh bonding
Jabra problems
I've had similar problems on a boring old Nokia 6310 with my BT200. In the end, all I could do was find the 'automaticly reconnect' option on the Nokia. during calls, the link is allways fine, but between calls, when I guess one end or the other goes to sleep, the link will drop out, and then instantly reconnect. This happens around 2 or 3 times an hour.
Is there a 'automaticly reconnect' option on your XDA?
All the best
James
OK, I finally sacked my Jabra 200, because of its instability. What use is a headset, that doesn't repond when a call comes in? :evil:
I bought a B-Speech from B-Data yesterday and it seems to be working much better :lol: .
Nokia HS-3w headset with XDA II
Well! I am using the Nokia HS-3W Bluetooth Headset with my XDA II . I can pair up two devices and use it for only ten minutes :twisted: . After that, the headset will off(goes to sleep) . I Have to turn on the headset every ten minutes. I ask the dealer about the problem. They told me this headset work fine with Nokia's phone. They told me , there is three color on the light. Red light will flash when you turn off the headset. Green Light will flash when you turn on the headset up to ten minutes, if cann't find the phone devices , it will goes off.White light will flash, when the headset connected to the phone. When I turn on the headset, I just can see the green light only.But, if someone call me or I make a call ,the white light will flash.After the that the headset will flash the green light again for about ten minutes and goes off. Can anyone help me with this problem? Thanks!
@[email protected]
Hi, I will like to ask how your headset B-Speech is working.
It works 100%?
I have a jabra 250 with the same problems as BT200
Please let me know
Regards
JoseF
The B-Speech Headset is working OK, however it doesn't solve the problems with the Microsoft BT-stack.
Some observations, probably also applicable to the Jabra:
:?: When you go out of range with the headset, it will probably not reconnect automatically (but how do you know)
:x On an incoming call, the XDA may be very slow in activating the headset, so you might miss the call (seems to be tied into what the XDA s/w is just doing at the time
When you turn the Headset off, make sure to turn it off on the Today screen first. And when you turn them on, make sure to wait about 2 sec. after you turn the headset on before turning it on on the Today screen.
:idea: What seems to work best, is turning that Headset off and then on again on the Today screen. It usually comes back after that.
Mind you, it isn't the headset thats causing these problems. Its just that Microsoft botched the Bluetooth stack - probably the programmers had blue teeth from all the wine they were drinking!
I've found the out of range issue to be mute on my jabra 200. The only time the bond is broken is when the headset has been turned off. Or sometimes when it has been on charge.....
Strange........I use the Jabra BT 250 with the MDA II and have non of these reconnection problems. I f I turn it on and place a call (or receive) it reacts immediately.
However, I cannot use the advanced Headset Profile features of the Jabra with the MDA, but this is not the fault of the Jabra........
Could the people who are having problems and the people who are not having problems with their Jabra BT200's please post their version numbers of the Jabra BT200. You can find the version number on the boom going to the microphone. It will be 2 numbers and a letter, like 48A or something like that. I'm testing a theory that I think will help identify why some people work and some don't.
Thanks,
LouisK
Ok, the number on my Jabra Bt 250 is 44B.
I decided to open a new thread although there were several threads on the use of bluetooth headsets. My intent is to explore whether there is a particular sequence that we need to follow when operating the XDAII and BT headset. I am using a Ericsson HBH-65.
First observation:
I notice that I need to end all calls via the bluetooth headset rather than from the XDAII. If I end a call using the XDAII (ie depressing the red button), for subsequent calls whether incoming or outcoming, I cannot use the headset. There is no connection between the 2. I seem to be able to simulate this almost 99% of the time.
Second observation:
I normally switch off my BT headset overnight for charging purposes etc. At the same time I deactivate the BT settings on my XDAII.
The next morning, I would activate the BT settings, BT profiles and then switch on my headset.
I notice that for the first call I made/receive the next day, I will have problems using the headset. I am not quite sure whether it is the case that I need to switch on my BT headset first and then the XDAII BT settings and BT profiles. I say this as to resolve the problem, I seemingly need to deactivate/activate the BT profile settings before it works and then for subsequent calls I would have no problems using the headset. This needs further testing to test my hypothesis.
Anyone notice anything different on their part.
regards
Same issues
I have had the HBH-65 and have noticed the same issues. I have also had an Logitech and did not have any problems with that.. I am guessing the issue is with the firmware on the HBH-65.
I use Bluetake GII with my xda2. No sequence, no problems. I never even think about switching it on or off. Works in any sequence. Nice looking too! :wink:
I have a Jabra 250, and I do not have to follow any ritual to have it to work fine
I have a Logitech Bluetooth headset with my Qtek 2020 (rom 1.60.21), and it works like crap.
First of all, the headset wont turn on/off sometimes.
Second - if its turned on, and the qtek has been turned off, i need to reconnect it, to switch automatticly when recieving a call.
Thirdly - both speak and hear is very poor quality/fare away (very silent) even though ive turned the volume to maxx.
BT Headset - Works Flawlessly
I have a Sony Ericsson HBH-30 headset and I never give the slightest thought to sequences or procedures. I can turn the headset on and off, the profile on and off, even the BT stack on and off - without ever having to re-bond or anything else.
Now if I could just voice-dial a call with the bloody thing I would be truly happy indeed.
Same problems but getting it figured out
I have the HBH-65 and it seems to work fine now that I've hopefully figured it out. I do a few things. First, I leave the Bluetooth on, on my i-Mate. Second, once it's in range I've noticed it takes about a minute for it to link up. When it links it either makes a single beep (if I just turned on the Headset) or a quiet click if it was already on. I doesn't work ALL of the time, but the more I use it the better it gets. I really expected it to be a little easier.
I have the HBH-200 with call display...which the salesman assured me that it would work with my XDA 2! Call display does not work, and if I end a call on the O2 the headset will hang. Other than that it's great!
I Have a XDAII and a HBH-35
They key to it seems to be not to turn anything off ! it's really frustrating when you think it's all linked up and then get in the car only to recieve a call and not be able to answer it with the headset.
If I have turned the headset off it's a right pain to bond again, red, green lights, funny beeps it's very confusing !
Once it's bonded it's great ! I am amazed with the call quality.
I have an Sony Ericsson HBH 35, I have no problem w3ith the bluetooth pick up call are end calls.
I can even transfer call from my bluetooth to the handaset and by reverse pick up call on my handset and then transfer the call back to the headset all I have to do his to hold the button on the headset fro a few second and the call transfer from the handaset to the bluetooth headset no problem.
Great piece of headset I would really reccomended it to anyone.
The rom on my XDA II is still the version 1.05
Regards
Gigino
Cheers Gigino
Do you ever turn your headset off or disable bluetooth?
I don't have any problems when it's bonded. Just problems if I turn the headset off to save battery
I only turn the headset off at night when I charge it. I use to swwitch off the headset but not anymore becauswe if it is on it use very very little power so it last all day with no problem.
The bluetooth on the XDA II I have never turn it off since I bought it 5 month ago the bluetooth headset on the XdA II is always on.
I've try it switch it of and then on the bletooth and the bluetooh heaset on the XDA II but when I turn it on and turn the headset on it all works fine.
They is no issue on the headset I've tryed every diffrent combinetion the is and the headset works fine.
I have never needed to rebond the headset with the XDA II.
The only thing I have not try is if I can receive a second caller.
Mean trying to switch between 2 caller when I have the chance I will try it.
Regards
Gigino
cheers
I have the BT800 and I have gotten some results but I want more people to try it,,, maybe with the Sony-Ericson devices. (I am not sure if the Caller ID and call list works with the Sony-ericson BT headset.. So, if you know it works, let me know.)
The BT800 needs BT stack 1.1 or 1.2 and Handsfree Profile to work.
I do not know what MS BT stack I am running, but, with the below handsfree reg hack, I got it to work.
Get rosco file explorer, (serial available from astalavista.box.sk , or use trial version). add the registry entry of Hkey_local_machine\software\microsoft\bluetooth add a new key while "bluetooth" is highlighted of "HandsfreeProfileOn"
Delete the pair on the BT800 and your PPC and turn them both off.
Turn back on the PPC and the BT800, Repair the device and the BT800, go to BT manager, click and hold on the BT800, select Handsfree.
Let me know how this worked, I have had mixed results. One time it did get caller ID and all worked well, but then only the audio was being played to the BT800 and the phone was also playing the audio and the mic did not work on the BT800, only on the phone.. BUT, this may only be my device for I have messed with it so dam much.
hello i have a HBH-DS 970 sony and it work good but i have a probleme and i know that i am not alone .
when the heaset is detected the phone purpose handfree and wireless stereo if i put handfree and wireless stereo i don t heard the ring on the phone only on the headset if i put only handfree the ring is on the phone (very good ) but when i want to listen music i must be configurate bluetooth et put wireless stereo to .
nobody can make a today plugin to have choise handfree or wireless stereo on the today screen.
thanks to your comment sorry for my english
sud the little frenchy
sud, this is a problem for all of Windows Mobile. The best solution I have is to put a BT icon somewhere on your today screen, so that at least with one click you can get to configuration and set "wireless stereo".
I usually put the BT icon in my system tray.
Funny, my Wizard will switch between handsfree, and stereo headphones when there is a call, or listening to music on my DS970 with no problems. I don't need to do anything.
Doesn't do it on my Universal though. As he says, you have to manually switch.
I am guessing there is a registry setting or 2 somewhere that will resolve this.
thanks for your interested for this probleme.
the bluetooth icone can be put on today screen but i search a solution for put an icone handfree and an other wireless stereo or like said alanJC maybe in the registry.
to be continued
@AlanJC: I understood the problem to be... well, the problem that I have! Maybe I misunderstood. It's not that if you are in 'wireless stereo' for music you can't auto-switch to 'hands free' for voice, and back again. It's that you have to set 'wireless stereo' in the first place, whilst 'hands free' seems to work by default.
@sud: I've never seen the Today icons you are looking for... and I've looked too. Great idea. PLEASE post here if you find them.
http://www.teksoftco.com/index.php?section=freeware here is the soft to switch but with the last rom is ok without it
Hello all,
I've had my TP for over a month now, and globally I'm pretty much happy with it. Of course there are some glitches here and there, but no doubt a firmware upgrade will fix those bugs soon.
That said, there's an annoying issue with the way bluetooth headsets work with the phone part. Let me try to explain :
- When an incoming call occurs and I answer using the "take call" button on my headset (which is a Plantronics Pulsar 590), sounds is transferred to the headset and everything works fine.
- When an incoming call occurs and I answer using the "answer" button on the mobile, the sound stays on the TP even if the headset is switched on and connected to the TP.
When the latter happens, I can't get the sound back to the headset. When I select "transfer to hands-free" from the phone menu, the transfer works erratically.
Is there a fix available somewhere to make sure that, when the headset is on and connected, the sound of an incoming call always goes to the headset?
Thanks a lot in advance for any help you may bring on solving this issue!
Are you using AEBPlus?
No (and honestly, I don't see how that relates to the problem)
Hi Guys,
I also have this issue.
But if I press the 'answer call' on the mobile the sound stays with the Touch Pro but if, once I realise what I've done, I press the 'answer call' on the headset then audio is transferred to the headset again.
Does that happen for you? I'm using an SBTHS-3500 BT headset.
Cheers,
D.
clandestino_usr said:
No (and honestly, I don't see how that relates to the problem)
Click to expand...
Click to collapse
Sorry, I had multiple tabs open for responses.
Copy'n'Paste error.
P.S. I had this issue on my TP and Diamond as well. I have since installed a 2.03-based ROM which fixes the issue (since you can no longer press the phone button to answer, but rather have to use a slider).