So I am trying to play with my new tilt for the first time, and after lots of reading I began to try. I am starting with POF's Hard Spl package, and I am stuck with that. I followed all of the instructions precisely, but when I get to the RUU screen, it says to connect PDA phone to the USB cable, and establish an Active Sync connection. Well it won't establish an ActiveSync connection now...and if I just check the box, I get the ERROR [260] Connection message, and it says to hit esc to finish. Then the phone is just stuck on the tricolor screen, and only thing I can do is reset.
So....now what? I have tried to google and xda search this problem, I saw one person with the same problem, but then posted back a little while later saying he resolved the issue, but didn't say how...
Any ideas?
Thanks in advance,
Michael
memnoch_thedevil said:
So I am trying to play with my new tilt for the first time, and after lots of reading I began to try. I am starting with POF's Hard Spl package, and I am stuck with that. I followed all of the instructions precisely, but when I get to the RUU screen, it says to connect PDA phone to the USB cable, and establish an Active Sync connection. Well it won't establish an ActiveSync connection now...and if I just check the box, I get the ERROR [260] Connection message, and it says to hit esc to finish. Then the phone is just stuck on the tricolor screen, and only thing I can do is reset.
So....now what? I have tried to google and xda search this problem, I saw one person with the same problem, but then posted back a little while later saying he resolved the issue, but didn't say how...
Any ideas?
Thanks in advance,
Michael
Click to expand...
Click to collapse
Yes. Use another computer.. or disable your firewall or de-activate your AntiVirus program. You have some sort of conflict in the drivers. It happened to me and the only it worked for me is when I switched to another PC to do the upload.
I will have to try it out on my laptop when I get up...but I have no firewall enabled, and no anti-virus running. But if this is a driver issue, then I don't see how those 2 things would come into play?
So, switching to my laptop worked, thank you for that. I have sucessfully installed Dutty's v3 rom, but now it seems my battery depletion is on a downward spiral. It has gone down 10% in less than 10 mins, and it is just sitting on the table, nothing running.
Any ideas on that?
Also is there anything else after the rom install that I should add/do? I
have seen a few different posts about radios...not sure will keep looking lol...
Thanks again,
Michael
I had the Error [260] Connection issue at some point in the beginning of flash process.
Changing to a different usb-port in my laptop solved it to me.
Related
I've been at this for 2 days now with no luck. I have my Tilt and I want to use Dutty's Rom V3. I've tried HardSPL sereval times with no luck. I use Vista and that seems to be the problem. I've tried using the method offered by the MrVanX website. Still nothing. I've searched the forums like crazy looking at a bunch of different solutions and trying them but nothing.
Is anybody willing to talk me through it on AIM. My SN is scoorch33.
My bootloader screen shows the thing below, and thats it.
KAIS1*0
SPL-1.56.0000
CPLD-8
Everything you need my friend is right here on this site. Sometimes it may take a day of reading before you find the answer, but trust me, anything that you are experiencing, someone else has already had and found a solution for that particular problem. For the hard_spl problem, which is the first thing that needs to be done, try this thread...it helped me http://forum.xda-developers.com/showthread.php?t=354061
I tried using the solutions from that page. I did what the instructions say and during the bootloader screen I get something like this.
KAIS1*0
Jump SPL
CPLD-8
After that I try what it suggests, running the Splash screen application but nothing happens. I extract the files onto my Desktop of my PC and I double click.
A MS-DOS prompt appears for a split second and then disappears. The same happens when I run KaiserCustomeRUU.exe. A brief flash of a dos prompt and then nothing.
My phone stays in the bootloader screen the entire time and then I soft reset, but there are no visible changes to the phone.
Maybe I'm doing it wrong.
I'm trying to do the White Screen Solution Method of flashing the phone. Right now the phone won't even stay on without the SIM card in. It gets to me entering the password and then shuts down and restarts again.
So I run the JumpSPL on my phone and it goes to tricolor mode.
I unplug and plug the USB cable. I then try to run the suggested RUU program. The progam flashes up for a second. I don't even see what it says. The phone still stays in tricolor mode.
Phone doesn't restart until I do a soft reset.
Anybody have any suggestions?
I got it to work.
Found an old harddrive and loaded up XP and did everything.
SBZRO said:
I got it to work.
Found an old harddrive and loaded up XP and did everything.
Click to expand...
Click to collapse
hmmm trying to use vista I see...
All,
Read the forums and done all the searches but struggling. Download the Kaiser-HardSPL exe and ran it on my PC (using XP). Get the tricolor and USB screen but then it tells me to disconnect and reconnect USB, but it never goes green again so consequently it doesn't go any further. I've reset the Kaiser and tried again but no joy. Thanks in advance
Read carefully, when you're in the tri-color screen and unplug/plug your device, the activesync icon shouldn't be green cause it is not able to detect your device as a WM one.
Gray is the way to go
j1ngles said:
All,
Read the forums and done all the searches but struggling. Download the Kaiser-HardSPL exe and ran it on my PC (using XP). Get the tricolor and USB screen but then it tells me to disconnect and reconnect USB, but it never goes green again so consequently it doesn't go any further. I've reset the Kaiser and tried again but no joy. Thanks in advance
Click to expand...
Click to collapse
Yes, I saw that. The icon has gone grey on my desktop. The next step though says connect the PDA back again via usb and establish a connection. How do you know if it has established. I clicked ok anyway ran the program but it can't read the existing rom info off my kaiser and comes back with a connection error
If i'm correct you should wait for a minute or two to let the ActiveSync connect to your Kaiser. After that it should be good to go further..
Be sure that the ActiveSync icon on your computer desktop is green at that stage..
j1ngles said:
Yes, I saw that. The icon has gone grey on my desktop. The next step though says connect the PDA back again via usb and establish a connection. How do you know if it has established. I clicked ok anyway ran the program but it can't read the existing rom info off my kaiser and comes back with a connection error
Click to expand...
Click to collapse
On your screen, at the bottom, it should say USB.
Once you see that you are ready to install the HardSPL
OK guys success. I think what threw me was the activesync staying grey during flashing but found a nice vid on youtube which helped. Many thanks
Hi there guys .
I've been searching and searching, and trying and trying, but I can't seem to get past this Error [262] when I'm trying to upgrade my ROM or Radio (HTC Diamond).
What I'm doing is this basically:
I downloaded DiamonCustomRUU.exe, put it in a folder with the radio/rom (say Diamond_Radio_1.00.25.05.nbh), I connect my HTC Diamond to my pc via usb, activesync is on, I start up the RUU, go through all the steps, then at the end when the update 'starts', my phone goes off, starts up in the 4 coloured screen, activesync stops, then my phonescreen turns grey with the progress bar (stuck at 0%), and on my laptop there's a progress bar as well. It does nothing, and after about 5 minutes, I get the Error [262].
I reinstalled Activesync, but no changes. I installed HardSPLL though. I tried another USB-port, doing it without my firewall on (someone suggested it, yes I'm desperate)... I have no idea where to go from here.
Can anyone help? (sorry if this is the wrong section..)
Love
Had the normal (signed)SPL instead of the hardSPL. Can be locked
Decided to take the plunge and flash my Dash 3G..downloaded the Dash3G HardSPL by JockyW, unzipped it on my PC and ran the auto.bat. Copied JumpSPL. exe to my phone and executed it on the phone. Ended up with a Jump address dialog box.
I'm sure I have overlooked something, but can't figure it out. HELP!
Thanks in advance.
Next steps
Figured out my problem, but have now ran into another.
When I get to the point where I click the trackball to continue execution of JumpSPL, the phone displays turns dark and then I lose USB connectivity. The romupdate displays on my PC, but I am unable to reconnect via ActiveSync. Ideas?
That's normal. After the JumpSPL starts on your phone activesync disconnects. Another type of connection (htc sync, you should see the driver in devicemanager) takes over.
Thanks Jockey. That may be the issue as it doesn't ever appear to switch to htc sync. I am also not seeing anything like that in the device manager. Ideas?
I do see JumpSPL on the phone.
I appreciate your help.
Hi everybody
I have an HTC Fuze (ATT). The ROM I used was NATF v5. series. I tried a couple of days ago to sync it with my computer but it gave me an "USB device not recognized" message. I did a hard reset but it didn't change anything. I changed the "Energy" rom, but I had the same problem. I tried now to sync the phone with another laptop but I have the same message, so something happened with the phone. What I noticed was the fact that actually when I hard reseted, I still had the NATF 5.series screen shot, even if the rom was the energy one. I appreciate each answer as I don't know what I can do more.
Adriciu
adriciu said:
Hi everybody
I have an HTC Fuze (ATT). The ROM I used was NATF v5. series. I tried a couple of days ago to sync it with my computer but it gave me an "USB device not recognized" message. I did a hard reset but it didn't change anything. I changed the "Energy" rom, but I had the same problem. I tried now to sync the phone with another laptop but I have the same message, so something happened with the phone. What I noticed was the fact that actually when I hard reseted, I still had the NATF 5.series screen shot, even if the rom was the energy one. I appreciate each answer as I don't know what I can do more.
Adriciu
Click to expand...
Click to collapse
Had you try other cables Sir?
NATF splash screen will remain there, because when you flash Energy ROM, it didn't contain splash screen, so it wouldn't be replaced.
I tried a different cable, as well as a different computer. On the new computer there was no previous activesync installed. This led me to belive that there is a problem in the registry somewhere, but I don't know what to change. I also installed the Activesync 4.5 several times. on the ald and new computer, but nothing helps. No firewall active.
Adriciu
<- same problem
Anybody has any ideas?
What about using other phones, if it's okay then the problem was on Your phone, vice versa.
In my opinion, to get phone connected, we must have Activesync (for Win XP) or WMDC (for Vista) installed, good cable (original preferred) and good phone condition (H/W or S/W)
Hope You solve it soon Sir.
I have reinstalled the ATT rom, but is still gives me a "USB device not recognized" message. So I think something is wrong with my phone. Is there any way where I can clean up the whole registry and start from a clean fresh phone?
Still not working.
I had a simmilar problem a long time back.... How I fixed it was I deleted that connection setting for that phone in activesync... Then rebooted...Try to connect it then... If it still doesn;t work, UNINSTALL activesync... reboot... reboot again for good measure.. then reinstall it... reboot... Then try to connect again.... a lot of steps, but it worked for me when I put a diffrent on an old phone I had...
OK, some updates. I tried syncing with another laptop and it is not working. I tried doing the same thing with an Apple comp and it doesn't even see it as an usb device. However I tried syncing wifi with my gmail account and it is giving me the following error message: "The configuration on your Exchange server prevents you from synchronizing. Support code: 0x85010004". So I think there is a setting I don't know how to change.