Database Info

WM 6 on MDA

Hello, I really would like to know about this, I have a T-Mobile MDA (USA) running WM 5 version 2.26.10.2 WWE. I downloaded this from the T-Mobile website and updated my phone. I would like WM 6 on my MDA but i have no clue on how to do it. So if someone could please help me to do that i would really appreciate it. Also i would like to know some of the advantages and disadvantages (if any) of upgrading to WM 6. I'm a complete noob to any of this so any help is appreciated.

killerkhatiby009 said:
Hello, I really would like to know about this, I have a T-Mobile MDA (USA) running WM 5 version 2.26.10.2 WWE. I downloaded this from the T-Mobile website and updated my phone. I would like WM 6 on my MDA but i have no clue on how to do it. So if someone could please help me to do that i would really appreciate it. Also i would like to know some of the advantages and disadvantages (if any) of upgrading to WM 6. I'm a complete noob to any of this so any help is appreciated.
Click to expand...
Click to collapse
Start reading the forums. Everything you need is found here. Best bet is to take time and read the stickies at the top of this forum and the Wizard Upgrading forum. Those will tell you the step by step instructions on doing all of this. But understand, this isn't just a simple application install, but an OS Install (and not one supported by your provider). So for most roms you will have to figure out how to setup GPRS and MMS to get them to work. So don't rush into this, but spend some time reading and learning (or you may wind up with a dead phone).
A really good post with tons of pointers to stuff is:
http://forum.xda-developers.com/showpost.php?p=1206964&postcount=894
Hats off to Carlosdude1991 for putting that together.

Thanks for the quick response, ive been reading up a little and so far it seems like the WM 6 Roms run faster than the originals, i have also learned that i have a G3 Device. Anyway im going to unlock my device and install WM 6 but i dont really know which ROM to get. Which is the best WM 6 ROM?

killerkhatiby009 said:
Thanks for the quick response, ive been reading up a little and so far it seems like the WM 6 Roms run faster than the originals, i have also learned that i have a G3 Device. Anyway im going to unlock my device and install WM 6 but i dont really know which ROM to get. Which is the best WM 6 ROM?
Click to expand...
Click to collapse
Ok, then start here and follow everything without skipping steps.
http://forum.xda-developers.com/showthread.php?t=298613
As for WM6, you'll have to decide what you really want. If you want a fully loaded rom, then try Faria's "the real thing". For a "clean" rom try NotTooSmart or Xplore 1.1. Also Zoki's NBD is getting good reviews (I haven't tried it).
The beta of Faria's Vanilla is going VERY well and will be a great rom when its released (watch for it soon).
Good luck and have fun.

I have another question though before i do that, after i get WM6 will everything work again like it used to, like phone, text and sms, camera, programs etc.?

yes they will, you will have to enter in the correct settings for T-mobile mms

I think this is my last question (actually last 2), On the guide it says to downgrade to T-Mobile 2.26 ROM, what does it mean by that, does it mean that I should install buttons 1.05 ROM and do the whole process and then install the T-Mobile 2.26 ROM which is the one I'm running right now? and wouldnt that re-lock my phone? and my second question is about how long would it take to go from an official T-mobile 2.26.10.2 ROM, Locked phone. to a WM6 unlocked everything working phone?
BTW thanks for all the quick responses and help.

http://forum.xda-developers.com/showthread.php?t=285435
Go to that thread and follow those directions. You have to use the lokiwiz to cid unlock your rom before you can add custom roms. Cid unlocking voids your warranty btw. That form is straight forward and works like a charm just do exactly what it says word for word.

I read it through a couple of times now, but i just don't get the part at the end where it says install the T-Mobile 2.26 ROM. I have that right now and wouldnt that just re-lock the phone? Also how do i Downgrade to the Button 1.05 ROM?

Alright, I understand where your coming from, I was in your shoes. lokiwiz will not work with 2.26. Therefore you have to downgrade your rom to 1.05( I used 1.8 because I couldnt find 1.5 and it still worked) Once you downgrade your rom then you can use lokiwiz to Cid unlock your phone. adding 2.26 after your cid unlock your phone will not lock it again given that you did everything correctly. 2.26 is a solid and steady base rom to use that doesnt have any bugs or anything. once this is all done you can put a wm6 rom on your wizard.

o ok i see, so i can download and install the 2.26 ROM from the T-Mobile USA website and it wont relock my phone, right? also "(i used 1.8 because i couldnt find 1.5 and it still worked)" you mean 1.05 right?

k2e15 said:
Alright, I understand where your coming from, I was in your shoes. lokiwiz will not work with 2.26. Therefore you have to downgrade your rom to 1.05( I used 1.8 because I couldnt find 1.5 and it still worked) Once you downgrade your rom then you can use lokiwiz to Cid unlock your phone. adding 2.26 after your cid unlock your phone will not lock it again given that you did everything correctly. 2.26 is a solid and steady base rom to use that doesnt have any bugs or anything. once this is all done you can put a wm6 rom on your wizard.
Click to expand...
Click to collapse
All this is correct, but let me stress... You have to get both IPL and SPL down to 1.xx or when you go back to 2.xx you may find your device isn't really CID Unlocked... So follow that thread. It tells you to do the button downgrade, then do lokiwiz, then you have to downgrade again if your SPL still hasn't changed. Once you get both to 1.xx, THEN you can go back to an official 2.xx rom (TMo 2.26 is the suggested one). THen as long as you stay on 2.xx and above, you will not have to the the 1.xx downgrade ever again. You will remain CID Unlocked during all your flashing adventures.

Thx for covering that.. I forgot about that one.. .. as for using 1.05 when i tried to click the link, I had trouble and had to search for a different 1.rom. checked the link today and it works again.. Would have saved some time and stress. lol

I have a question, when i reach the part right after downgrading to 1.05 ROM and i click enablerapi do i install it to anywhere or just click it then run the lokiwiz.bat on the computer?

Install to the C Drive I believe

killerkhatiby009 said:
I have a question, when i reach the part right after downgrading to 1.05 ROM and i click enablerapi do i install it to anywhere or just click it then run the lokiwiz.bat on the computer?
Click to expand...
Click to collapse
Are you following this?
http://forum.xda-developers.com/showthread.php?t=285435
It tells you there in the steps on where things go... Basically the enablerapi can be anyplace on your phone, just get it over there and run it. But Lokiwiz needs to be on the C:\ drive of your PC to work properly I believe

alright i have succesfully installed WM6 " the real thing" but now i cant make any SMS messages? how can i fix this, i know you have to change the address or something but i have no clue where to go so i can do that. Also is there a way to get free internet from T-Mobile USA? I also have another quesiton, how come sometimes in the little icon next to the signal icon, its G and other times its E? does it make a difference?

killerkhatiby009 said:
alright i have succesfully installed WM6 " the real thing" but now i cant make any SMS messages? how can i fix this, i know you have to change the address or something but i have no clue where to go so i can do that. Also is there a way to get free internet from T-Mobile USA? I also have another quesiton, how come sometimes in the little icon next to the signal icon, its G and other times its E? does it make a difference?
Click to expand...
Click to collapse
You can't do SMS and MMS because you haven't set that stuff up yet apparently. EIther go to the T-Mo site and find the settings to plug into your phone, or search around here for the cabs for T-Mobile (I'm on Cingular so I don't have the T-Mo cabs to post)
G is straight GPRS. E is Edge (faster). I think the default TMo and Cingular stock roms turn this off from switching (so they always just show E). So now you are seeing when you are connected to the better net (but a lot of people don't care for that. again there is a cab around to turn that off)
Congrats on upgrading successfully.

ROM 1.05
Just in case this might help. Here is the link for the bottom 1.05 ROM. http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html

killerkhatiby009 said:
Thanks for the quick response, ive been reading up a little and so far it seems like the WM 6 Roms run faster than the originals, i have also learned that i have a G3 Device. Anyway im going to unlock my device and install WM 6 but i dont really know which ROM to get. Which is the best WM 6 ROM?
Click to expand...
Click to collapse
my advice is to download awizard thats the way i unlockt my mda vario
then flash it whith a black diamond 3.0 rom i think its the best and the fastes
sorry for my engilsh i am not that good
good luck

spl lowering

does any one now how to lower the spl . when u start the ppc mine is 3.08 and i need it lower so i can unlock my phone

Well, my guess is that your phone is already unlocked if your SPL is 3.08.
Is is a G3 or G4 Wizard?

G3 But I Wont To Put Black Diamond On It

So just try to launch the setup for BD to know if it really isn't already unlocked (in case it is, the Rom will install, and if it isn't, then it just won't, so theres' no risk for your phone.

Ya It Says Like Bnf Error

So you just have to follow the Wiki:
http://forum.xda-developers.com/showthread.php?t=263116

i need to downgrade me spl first i no how to unlock it

So what? Can't you READ? Everything is written in there, including the way to downgrade.
Here is a link to the adequate Rom since you seem so lazy...
Good luck
http://c4software.another-team.com/wm5.0/Downgrade/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe

lol im not lazy i have read so many tutorials on to unlock to phone

Just to forewarn you, do not install the downgrade ROM until you bring your IPL/SPL down from 3.08 to 2.xx. If you don't you may end up like a lot of other people on here where you can't upgrade the IPL after you get done unlocking your phone and go to install WM6. To get it down, just go to your service providers website and download their official version of their ROM and install it first and that should bring your IPL/SPL down to a 2.xx version, then flash the downgrade ROM.

xeno1 said:
Just to forewarn you, do not install the downgrade ROM until you bring your IPL/SPL down from 3.08 to 2.xx. If you don't you may end up like a lot of other people on here where you can't upgrade the IPL after you get done unlocking your phone and go to install WM6. To get it down, just go to your service providers website and download their official version of their ROM and install it first and that should bring your IPL/SPL down to a 2.xx version, then flash the downgrade ROM.
Click to expand...
Click to collapse
I did find one workaround that appears to almost always work is to have a minisd with a dumped raw image of a previous rom with ipl/spl included (r2d all command)...this was able to downgrade a phone on 3.08 back to 2.24 even after having gone to wm6. (it downgraded it back to wm5 at the same time)...conventional flashes were failing due to the ipl/spl.

ok thanks i will do that then i will unlock smart thinking

famewolf said:
I did find one workaround that appears to almost always work is to have a minisd with a dumped raw image of a previous rom with ipl/spl included (r2d all command)...this was able to downgrade a phone on 3.08 back to 2.24 even after having gone to wm6. (it downgraded it back to wm5 at the same time)...conventional flashes were failing due to the ipl/spl.
Click to expand...
Click to collapse
Yeah, downgrading your IPL/SPL is easy, it's when you go from a 3.xx IPL/SPL straight to a 1.xx IPL/SPL that can cause problems, like your IPL sticking at 1.01 afterwards and not wanting to upgrade back to a higher IPL.

YA but i cant find a downgrade for my spl

In the future, don't send private messages to people who haven't contributed to this thread. If you can't figure out how to downgrade and/or unlock your phone after reading the many, many threads on how to do it, I suggest sticking with WM5.

Here, run this. It's an IPL/SPL version only. It won't affect anything you info or programs you have loaded on your phone right now, all it will do is lower you back down to an IPL/SPL of 2.26.

ya that made me ipl 2.26 not my spl

That's not normal, try running it again. I think I just put a file that will change it to 2.25 in another post that you started. If the 2.26 one doesn't work after running it again, try the 2.25 one and see if it works for you.

Just install a factory T-Mo or Cingular ROM
(Gotta locate 1 yourself)
You'll lose all your info but you wanted to flash another Rom anyway.
You gotta keep a factory Rom handy when things go wrong

cujo did you just buy an 8125 because you think it looks cool or do you actually understand the phone? It seems to me like you should be using a razr or something less complex than that...

htc wizard cingular 8125 unlocked need help please

Hi I love this site. I need some help i did plently reading on roms n flashes and tried plenty out. My Question is that i have an htc 8125 phone which is unlocked and has windows mobile 5 on it and is is ilp 1.05 spl 3.08. I wanna put windows mobile 6 with the touch flow and cube but so far I ain't able.
I tried out TNT_5.0_Wizard_TouchFLO and NBK 9 on the Tnt i did it with active sync. I noticed on using TNT at starting my phone on i Get a TNT windows mobile 6 screen then when the phone boots up it customizes cingular and im back with windows mobile 5.
anyway to put windows mobile 6 and touch flo.
thanks for the help

When downgrading your phone so that you can unlock it - you need
Both IPL and SPL @ 1.XX
Yours are not the same - so you need to redo the process to get these two numbers to match. Flash the button rom.
Then, you need to flash a stable oem rom - like the Tmobile 2.26
In order to flash WM6 roms - you need ipl and spl of 2.XX or greater.
You've mentioned that you did some reading - do a little more. Read the unlocking and flashing a wizard posts, follow each step - do not skip any. Take your time, the how to's are very detailed - but they are bang on.
Good luck

htc 8125 problem!
Hi that such I have written for several sides asking the same thing, which happens it is that I have a htc cingular 8125 and need the help someone who can devote a solution to the problem that on having connected my htc to the pc, the activesync it synchronizes well and habia could before formatting the memory could spend(pass) of quite files etc.. But now after erasing I want to install any rom and it turns out that the rom does not recognize the htc, me mistake and the this battery 100 % loaded, the cable in good conditions, I changed the framework into the last one to the pc etc.. And nonetheless I could not have installed the rom.. not that to do.
Thanks...sorry for my bad english.

Is your phone a G3? Install SuperCID.
Is your phone a G4? Run HardSPL.
Once that is done, you should be able to load the Wizard Love ROM.
Then, you should be able to load any WM6 ROM from these boards.

How I flashed my TYTN-II successfully without HARDSPL ?

Hi,
I purchased my TYTN-II from UK as sim free in Oct-07. From the last five months i was under the impression that HARDSPL is very much necessary for flashing. Though i never tried to HARDSPL my unit. Last month there was RUU upgrade from HTC e-club. Since it was from HTC and there was no special instruction before running RUU. So i run the RUU directly and my unit was successfully upgraded to WM 6.1.
After that i realised that 6.1 is not stable. So, with the help of the forum ... i downloaded the WM 6 shiped RUU from the forum and run directly and again my device accepted the WM6.
Now, i am confused that how this happened ? am i not suppose to HardSPL my device before flashing specially at downgrading level ?
OR since my device is SIM Free / Unlocked thats why it doesn't need HardSPL ?
I am just trying to educate myself nothing else ...
Regards

i believe that u still need to hard spl the right spl for that rom u installed...the spls are stickied in this forum
admins = plz shut this thread down...

I always thought it was normal for sim free phones.
I could just be thick. But I thought it was due to networks and simlocks that people had to HardSPL.
So its just for cooked ROMs. I get it now. So you flashed a HTC ROM on a HTC device. Which would have flashed the correct SPL anyway.

Hard SPL's allow you to flash cooked roms safely without bricking the device. Since you flashed an official rom from HTC you wouldn't require a modded SPL

There are different hard spl's for wm6.1 thats all. To be honest you are normally safer just to hardspl anyway. Back in the day, if you hadnt hard spl'd your phone and you bricked it, it was basically impossible to fix. Not sure these days on the kaiser, i have never tried not hard spl'ing mine so i couldnt say.

OEM SPL does NOT allow you to downgrade even if the ROM fits your device. I don't know why you not taking HardSPL, if you worry about the warranty, just go ahead to flash ROM with HardSPL, then flash OEM SPL back after it.

if you device is from HTC and not locked to a provider you can flash roms from HTC-E club BUT!!! your phone is not truly safe HardSPL is like a condom for your kaiser if something happens lets say the USB plug comes out while flashing NOT having HardSPL you might have an issue BUT you probably WILL... Just do yourself a favor and flash HardSPL you can always revert back to the shipped SPL if you need to for a warranty return......

austinsnyc said:
if you device is from HTC and not locked to a provider you can flash roms from HTC-E club BUT!!! your phone is not truly safe HardSPL is like a condom for your kaiser if something happens lets say the USB plug comes out while flashing NOT having HardSPL you might have an issue BUT you probably WILL... Just do yourself a favor and flash HardSPL you can always revert back to the shipped SPL if you need to for a warranty return......
Click to expand...
Click to collapse
Thanks austinsync,
It seems to me that i almost tried to kill my device. Now advice me which Hard SPL should i use for TYTN-II. I mean 3.28 or something else ?
They look like same to me ...
Regards,

Please help with Treo 750 Unlock!!!

Hi,
i have Treo 750 want to unlock!!
IPL:0.20
SPL: 0.24.0000'
i try with Cheeta unlocker and MAGIC Unlocker, both not work.
it this because of the new SPL0.24??
can anyone give me instruction how to please!!
thanks

i had same problems with my treo. first like oli says in his first post about hard spl make sure you have net compact framework 2.0 on your computer. what worked for me was in your c drive there is a folder called tempche. delete that file then run unlocker again. i only did first step on my treo just so it would be hard spl'd. never did step 2 and so on cause i didnt feel a need too.

thanks man, just delate the tempche folder then everyhting run smoothly.
cheers

Good for you!
Hi:
Where do you find the SPL and IPL information?
And can you tell me what SPL actually is?
Thanks!

spl
im not sure about what spl means but i do know that you need to have it done in order to install a cooked rom. it basically unlocks your phone so you can flash different roms that the chefs cook. there really isnt to many people cooking roms for the treo. theres only about 3 or 4. i think everybody got different phones so thats why your not getting responded too very quickly. i too have a tilt and a treo and i like to bounce back and forth between phones. i have the wm 6.1 lite rom on my treo. if your looking at just upgrading from wm 5 to wm 6 you dont need to do a hard spl. stock roms allow you to flash without unlocking your phone. im not a computer genious here but i will try and assist you however i can. ive been in your shoes before trying to figure all this stuff out.

i forgot to answer your question about where to find the spl. it shows up in your bootloader screen. you can see it by pressing down the lower left side button and pushing soft reset which is located on the other side where you put your mini sd in. there is a small whole that you use your stylus to push in. you can just soft reset again to get out of the bootloader screen.

helpeee
i used cheeter unlocker. I
did step one and two
successfully. But at the end i get
the debug error which some
people got. So i copied htc herm
unlock v3 to the phone. I ran it
from phone and selected sim
unlock and it was succesfull. But
when i turn on radio, i get "you
have tried 5 times, wait for time
out ****".
Please anyone, what am i doing
wrong, or what should i do to
unlock my machine?? It has wm6
from at&t.
_________________