Database Info

How to flash a new ROM to your Wizard... a little tutorial!

This guide was written a long time ago. I recommend people to use this more up to date guide:
Wizard Windows Mobile 6 for newbies
I've got a lot of post behind my name, but most of my posts are answers to the same questions over and over again. It seems very hard for "noobs" to find the answer to their question quickly on the forum. I quickly wrote a little step by step tutorial for them. Hope it helps!
Suggestions or corrections are always welcome.
You want to flash your wizard, but don't know where to start. Try this:
0. First determine if you got a G3 or a G4 device. When you turn on your device from can can see you're IPL and SPL version on the screen. If you got IPL/SPL 1.xx or 2.xx you've got a G3 device. If the IPL/SPL shows 2.xx.xxx1 you've got a G4. Go to step G3.1 if you got a G3 and G4.1 if G4.
G3.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G3.5, NO go to step G3.2
G3.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). If you got IPL/SPL 1.xx go to G3.3. If you got 2.xx go to G3.4
G3.3 Download button rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.4 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.5 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G3.7, NO OR DON'T KNOW go to step G3.6.
G3.6 Follow this great thread by Dr Puttingham: The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards. Don't skip step 17! Flash the T-Mobile 2.26 Rom! Go to step G3.8 if you got the T-Mobile rom with IPL/SPL 2.26 on your device after doing this.
NOTE: Some people seem to have problem with flashing the button rom in this step (stops at 98% with error 302). Replace button_rom with Xda_MiniS_LaunchROM_v154102 and follow the rest of the steps normally when this happens!
G3.7 Download T-Mobile 2.26 rom and flash it to your device! Done? Go to step G3.8.
G3.8 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise! It wasn't that hard, was it? If you still got an older OS version after flashing then you're not CID-unlocked! Go back to start!
------------------------------------
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!

Nice one.
One thing I've found is since the Mods split the WM6 stuff to a seperate forum a lot of noobs are in that forum and they don't see the stickies over here now (I've had a couple PM me directly asking where this Wizard Upgrading forum is at that I refer to in my posts ). So I think we need some stickies like this or something in the WM6 forum (or a sticky at the top of that forum with a pointer to this forum and maybe certain posts over here).

Nice. Maybe we should add a link in the Wiki to this...
--M

Corrected the links to wizard_love.... they didn't work.

I found this solution much better than shelltool for flashing my G4 CID-locked Wizard:
http://forum.xda-developers.com/showthread.php?t=271043
Shelltool can only flash the OS while using this modified RUU you can task the OS, splash screen, and the radio. Plus this modified RUU will also flash Wizards that do not bootup normally.

You can't flash a touched OS that way in a CID-locked G4.... only some 2.26 roms will work. Trying this with WM6 will go to 100%, but you're "old" OS will startup again.

Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...

JBLaze407 said:
Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...
Click to expand...
Click to collapse
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV

mfrazzz said:
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV
Click to expand...
Click to collapse
Thany you very much for the info...

nice work....stiky.....
could someone post the above info in wiki..... so we can redirect questions to wiki.

If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?

bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
Good question.... have you flashed T-Mobile rom before? If you haven't you will get the strong 2.26 IPL/SPL. It prevents many problems! This step is to prevent people to upgrade to WM6 with other IPL/SPL!

bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!

mfrazzz said:
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!
Click to expand...
Click to collapse
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?

pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
Good question. I don't have a G4, but I'd think the same would hold true to get a stable / clean base for the new custom rom.

pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
NO! that rom has IPL/SPL in it. Don't try flashing this rom onto a G4! It could brick your device!

thanx a lot !

Great job vippie!
I've updated my thread to reference this.

Please update the first post
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?

mfrazzz said:
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?
Click to expand...
Click to collapse
Good one.... updated the starting post! Thnx!

G4 Help plz

Hi,
Im have a G4 mda vario!
ipl 2.21.0001
spl 2.21.0001
original software t-mobile.
Im trying to figure out the best way to upgrade to wm6. Some topics say to unlock CID but with a G4 you must pay for it. Other topic say use hard spl or soft spl is this also for CID unlocking?? I dont know annymore so can someone help me?? The steps I need to make to install wm6 on my device.
And for the best wm6 rom on htc wizard aka mda vario.
Thnx!
Kevin

i have tmobile mda vario
i am running tnt 1933 which seems to be for me at least the best all round rom. and its as stable if not more than stock wm5
i used soft spl.
you should read the instructions fully and make sure you are happy before proceding.
I recommend.
1) Hard reset
2) hook up to pc and run wizard service tool (search the forum) and use this to enable rapi and cert etc.
then run the soft spl.
I had problems first couple of times where it would go black then i get funny error in green text but never actually flashed anything. But i think the hard reset and enable rapi stuff fixed that.
hope thats of some use.
cant recommend tnt rom enough

if you want to save yourself an absolute tonne of mucking about and trying to figure everything out, i recommend you splash the cash and pay the £20 on http://www.imei-check.co.uk/
i have a g4 and used these guys, worked with absolute no issues, and im on the xmr5 rom ( or whatever its called )

funy said:
i have tmobile mda vario
i am running tnt 1933 which seems to be for me at least the best all round rom. and its as stable if not more than stock wm5
i used soft spl.
you should read the instructions fully and make sure you are happy before proceding.
I recommend.
1) Hard reset
2) hook up to pc and run wizard service tool (search the forum) and use this to enable rapi and cert etc.
then run the soft spl.
I had problems first couple of times where it would go black then i get funny error in green text but never actually flashed anything. But i think the hard reset and enable rapi stuff fixed that.
hope thats of some use.
cant recommend tnt rom enough
Click to expand...
Click to collapse
the above recomendation are good , in fact that's what i have done to update my G4. I would only add to that rembember to save your current rom and extended rom before update. so you may downgrade if you have any problem with wm6.

Unable to load ROMS, AT&T Tilt

Hi,
I have a Tilt, the ROM version is: 1.57.502.2, Radio version: 1.27.12.11. I am trying to downgrade the phone to WM5 or to one of the cooked roms published on this site. I have spent hours reading the WIKI section and many posts. I have tried to install the HARD-SPL however in the begining I had the white screen problem. After using the JUMPSPL, I think that I have managed to install the Hard-SPL (The version that the bootloader shows is: SPL-1.0.Olipof.
I have also unlocked the phone and the CID using tools available on this website. I have no way to check if the unlock works since I do not have another SIM with me right now.
The problem that I am having is that every time I try to install a ROM, I start the upgrade wizard, and get to the point where the phone shows a promt that asks me if I want to approve the execution of a file. I confirm it and then the phone reboots, shows the AT&T logo right away and reloads everything. I do not see the bootloader and after around 60 seconds I get the 260 error on my computer telling me that there is an update error and that the update utility could not access my PDA phone.
I have also tried to get into the bootloader manually, then connect the USB while ActiveSync is open and load an ATT rom (It's an older one with WM5 provided by Cingular) however I get the same results...
Can anyone give me some guidance? Any advice will be greatly appreciated!!!
Thanks,
Joe
P.S. The computer's OS is windows XP, I have turned of the Anti-Virus Scanner (AVG)

dude, there is no wm5 for the tilt........i think you are trying to load an 8525 rom on the the tilt and that is not going to work

What about a cooked rom?
Thanks for your reply. Is there any way to install a cooked ROM instead of cingular/ATT provided Roms with WM5?

logmaster said:
Thanks for your reply. Is there any way to install a cooked ROM instead of cingular/ATT provided Roms with WM5?
Click to expand...
Click to collapse
Like XtreMe_G said, there is no WM5-ROM available for the Kaiser. You can only use WM6/WM6.1 ROMs.
Why would you want to use a WM5 one?
If you want to flash one of the WM 6/6.1-Rom's, read the "Introduction to ROM flashing" (link below) .

This thread needs to die...
There is no WM5 Rom for HTC Kaiser Model.
Nobody has cooked one.
HTC didn't OEM one.
IT DOESN'T EXIST.
RTFF, you'll find everything you need to know about flashing cooked Roms but you will only find WM6 & WM6.1 Roms.​

Order of events!

Just so I don't get flamed to bad for asking a what some would consider a simple question, I had an 8525 that I made SuperCID and HardSPL, so I have done this before. I have also read the majority of material in the wiki and the forums on what I would like to do.
So here goes,
I just purchased the Tilt and am looking to do the same. It is stock to the block right now.
ROM 1.62.502.0
Radio 1.27.14.09
Protocol 22.45.88.07H
My question is what is the sequence of events that I need to do in order to get my phone SuperCID and HardSPL to the point I can start using some of these wonderful 6.1 ROMS?
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
Now what SuperCID? I found 2, here http://forum.xda-developers.com/showthread.php?t=361236 and here http://forum.xda-developers.com/showthread.php?t=375583
Any guidance would be very appreciated.
Thanks for your help
JD

The hardSPL depends on the ROM you're going to flash. Some ROMs work better with certain SPLs. Check.
For ease of mind, hardSPL first then security unlock. You can't go wrong in that order.

JudgeDredd67 said:
Just so I don't get flamed to bad for asking a what some would consider a simple question, I had an 8525 that I made SuperCID and HardSPL, so I have done this before. I have also read the majority of material in the wiki and the forums on what I would like to do.
So here goes,
I just purchased the Tilt and am looking to do the same. It is stock to the block right now.
ROM 1.62.502.0
Radio 1.27.14.09
Protocol 22.45.88.07H
My question is what is the sequence of events that I need to do in order to get my phone SuperCID and HardSPL to the point I can start using some of these wonderful 6.1 ROMS?
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
Now what SuperCID? I found 2, here http://forum.xda-developers.com/showthread.php?t=361236 and here http://forum.xda-developers.com/showthread.php?t=375583
Any guidance would be very appreciated.
Thanks for your help
JD
Click to expand...
Click to collapse
Ok, so I don't know about the super cid process but here's at least how you can start the journey:
Copy KAIS_SSPL onto your device
take out sim card and SD card
run KAIS_SSPL
Unplug USB wait 5 -15 seconds, plug in.
Run the Hard_SPL of your choice depending on your ROM choice. Seems like the ones out there are using 3.56, but it varies
Make sure to also flash a compatible radio!
Viola! you are done and ready to flash a ROM!

JudgeDredd67 said:
J
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
JD
Click to expand...
Click to collapse
1.) Flash 1.1JockyW HardSPL
2.) Using Jockys SuperCID process security unlock your device.
3.) Flash to any other HardSPL
4.) Flash the ROM of your choice.

Thank you all for your comments. I feel a lot better going into this now.

Noob question sorry. Sequence of events....
Appologies in advance as this is obviously a nooby question....
I have just aquired a t-Mobile branded MDA Vario III. I want to CID/SIM Unlock it as well as Hard-SPL it so I can install whatever ROMs I would like.
I previously had a HTC Wizard that I CID & SIM unlocked with the Lociwiz tool, however I had to downgrade the IPL/SPL to version 1.x to get this to work. Once it was unlocked I was able to install any ROM. I am looking for a similar thing with my new Kaiser and I can't find a Wiki or guide explaining the steps. It seems there are 1.x HardSPL's as well as Security unlockers, plus 3.x HardSPLs but no definitive guide as to the correct sequence.
1. I want to unlock the phone so I can use any SIM
2. I want to unlock the phone so I can install any ROM
With the Wizard I had to downgrade IPL/SPL run the Lokiwiz tool and the upgrade to whatever I wanted. How do I do the same with the Kaiser?
Sorry....
Andy

ADB100 said:
Appologies in advance as this is obviously a nooby question....
I have just aquired a t-Mobile branded MDA Vario III. I want to CID/SIM Unlock it as well as Hard-SPL it so I can install whatever ROMs I would like.
I previously had a HTC Wizard that I CID & SIM unlocked with the Lociwiz tool, however I had to downgrade the IPL/SPL to version 1.x to get this to work. Once it was unlocked I was able to install any ROM. I am looking for a similar thing with my new Kaiser and I can't find a Wiki or guide explaining the steps. It seems there are 1.x HardSPL's as well as Security unlockers, plus 3.x HardSPLs but no definitive guide as to the correct sequence.
1. I want to unlock the phone so I can use any SIM
2. I want to unlock the phone so I can install any ROM
With the Wizard I had to downgrade IPL/SPL run the Lokiwiz tool and the upgrade to whatever I wanted. How do I do the same with the Kaiser?
Sorry....
Andy
Click to expand...
Click to collapse
Since you are a Senior Member, you should already know the first rule is to search before creating new threads. However, since I am in a good mood from starting my new job this week, I will "help" you out. Check out the threads below, and after some in-depth reading, all of your question will be answered.
HardSPL: http://forum.xda-developers.com/showthread.php?t=334679
Sim Unlock: http://forum.xda-developers.com/showthread.php?t=361039
Now here is your nickels worth of free advice: Do NOT attempt to run the SIM Unlocker with a WM 6.1 ROM or the 3.xx HardSPL installed.

Closing this thread so it can fade away....

Rom install issues

So I have followed the guides, two of them conflicting each other (one tells me Wizard Love while other says Button)
So I pick wizard love because I did the factory update a few years back to 2.25
use loki3
run tmobile 2.26 and it fails
run the 3.08 and it works
try to install TNT roms... all get stuck at 99% except one but the rom doesn't work because I am still on windows 5.1
Now on my third attempt it gets stuck at bootloader. Can't get the phone to turn back on to normal mode just to use it and forget about trying these roms
Any ideas?

Got button to work some how
Now I am at IPL 1.01 and SPL 3.08
Hopefully I can redo everything and get 6.1 to work
It tells me my CID/SIM but no where does anyone tell me where I need to insert this ID code at.

ID code? What do you mean by that?

I ment CID, it was telling me the CID like if I needed to enter some sort of menu and run it
Running t-mobile rom again, hopefully this works

You sure that it wasnt asking for a SIM unlock code? OR was it giving you a "data crashes" message?

Nope neither of those.
Anyways
Tmobile screen pops up now with 2.26/2.26
In regards to installing new roms, do I just launch ROMUpdateUtility or Do I need to do a CID unlock again?
Also saw there is 3.08/3.08 available, Update before or after upgrading the wm6.1 rom?

Well, lemme ask you this, what is your device? Is it a G3 or a G4, if G3, then sure, update your IPL/SPL after you upgrade. If it is a G4 however, FOR THE LOVE OF TUNA DO NOT upgrade your IPL/SPL or you will have a brick on your hands. And also, if you have used HardSPL, then no, you do not have to CID unlock your device again. Personally, I just use the SoftSPL method each time I load a ROM. If your device is a G4, I have made a guide in the G4 section that should help you. Its got screenshots and such aswell.

G3
Yay somehow it worked this time, 6.1 is nice
I did softspl
3.08 worth it?

If you device is G3 - FORGET HARDSPL
You mention that you have IPL 1.xx and SPL 3.xx
get WST - Wizard Service Tool and follow the instructions to cid unlock you device, unfortunately you cannot unlock your SIM with the SPl that you have for now
After that flash a carrier ROm to align your IPL/SPL to 2.xx

Ohh it now displays 2.26 on both IPL/SPL
From what I read, 3.08 is mainly for the european radio brand in terms of what the focus on it was for
<---AT&T
Hopefully this will be my last month with this company, figured I try some things out before I put the phone away or give it away to a friend.

Ok, you have a G3 device
Get WST: http://forum.xda-developers.com/showthread.php?t=329170
Install in your PC (XP not Vista), check the situation about your CID and SIM
If you have CID unlock = SUpercid you can flash any ROm you want, if not you must downgrade to IPL/SPL 1.xx (Button Rom)
WST Unlock only works with IPL/SPL 1.xx
Note that SIM can only be unlocked with your SPL as 1.xx

go on run, type msconfig and open that, close all microsoft services and install,

Ckamc said:
Ohh it now displays 2.26 on both IPL/SPL
From what I read, 3.08 is mainly for the european radio brand in terms of what the focus on it was for
<---AT&T
Hopefully this will be my last month with this company, figured I try some things out before I put the phone away or give it away to a friend.
Click to expand...
Click to collapse
DUDE! I'm your friend you can give it to me
Or you could use tmobile with that phone (or any other company that uses sim chips for service) .
Once you have it completely unlocked (cid/sim) you can take it traveling to other countries and use their prepaid sim cards... This is an open phone. dont get rid of it.
on second thought, I will buy it from you if you dont see a reason why you would keep it. I could use a backup to test my cooking on PM me

HAHAHAHA
S.V.I said:
DUDE! I'm your friend you can give it to me
Or you could use tmobile with that phone (or any other company that uses sim chips for service) .
Once you have it completely unlocked (cid/sim) you can take it traveling to other countries and use their prepaid sim cards... This is an open phone. dont get rid of it.
on second thought, I will buy it from you if you dont see a reason why you would keep it. I could use a backup to test my cooking on PM me
Click to expand...
Click to collapse
You know when an oportunittie comes huh!
I can buy it too but its more glad to see a wizard function well with 6.1
hope you can unlock and upgrade... if not... READ a lot.

Losing Mind (again)
OK, here we go.
First off, I am in no way new to Flashing or the logistics behind it. I am sure this is just something that I cant find by searching. But my problem is this.
I have a G3 TMOBILE USA MDA (Wizard). I have used the lokiwiz2 unlock software several times and according to the program I am SUPERCID unlocked. I am able to flash ROMS all day long. I get no error about loading. What is happening is that I almost always end up with the same default ROM after the FLASH is completed. I am now sitting with the Button ROM on the unit. I assume if the Button ROM loads, then I should be CID Unlocked otr it would not load (or is this my mistake in thinking?)
As my MDA sits now, I have the Beer Mug Displayed, IPL 1.05
SPL 2.26 GSM 01.12.10 OS 1.5.4.2
Now, if I go and try to Flash to one of the Two ROMS I want to go to
TMOUS_MDA_5.2.1629_Wing_Port_1.1 (Boring ROM) or I try with SNN 3.1 it will run the procedure perfectly, and I will end up with a Barebones version of Windows Mobile 5.0. This is wild.
Has anyone seen this happen and is laughing and going "Been there, here is the problem,,) or do I need to discuss this in more detail.
Im wondering if the ROM Upgrade Software is grabbing a ROM from elsewhere on my Hard Drive and is installing it from cache or something like that. Is there another version of the OS Upgrader that allows me to tell it exactly what ROM I want installed, instead of just installing whatever it wants.
Thanks for the help, after two days of searching and looking around, I can deal with amteur hour emabreesment, just HELP!!
My xv6800 and my 8125 was a breeze compared to this nitemare. (BTW, I also flashed this 2 years ago with the TMOBILE USA Official Release, no issue)

wyreless
Well,these are symptoms of CID not unlocked.Button's Rom flashed doesn't mean its CID unlocked,its a patched IPL/SPL rom simply to downgrade to IPL/SPL 1.xx for CID unlocking.
Simply,download WST_4.2.2 and run it to verify the CID lock/unlock status of the phone and do the right thing onwards.

Thank You Zabardast for the quick and to the point answer.
I was thinking in the back of my head it was a CID issue. It was just that everything seemed to be "moving right along". I sthere an easier or better Unlocking soiftware then lokwhiz for the Wizard Series, specifically my USA Tmobile MDA?

Well,if you have Button's Rom running successfully,so its IPL/SPL must be 1.xx already,there shudn't be any problem to use lokiwiz02b to CID unlock the phone,you can even use WST_4.2.2 tool also to easily CID unlock the phone.
There's no other method known to get CID unlocked a wizard freely,unless you are ready to pay to IMEI company to get a unlock code

hey alll..ok i screwed up
i downloaded Charecters ROM..i used WST and it showed that my device is G3 and its CID locked..well i just started the Flashing and it stuck at 99%
now it wont load any ROM and just as i came from school..its not evening starting..its not evening charging..please help any one

for one to flash a rom you must CID unlock it first...