hardSLP and USB connectivity - Tilt, TyTN II, MDA Vario III Windows Mobile ROM De

I'm trying to flash hardSLP, I get to the tricolored bootloader screen with USB at the bottom but when I unplug the USB and plug it back I can not get active sync to connect. Is their something I missing?
Thanks,
Matt

your system is probably installing the wrong USB driver for the new updated mode - you may need to force an install of the proper driver. in my case, running vista ultimate, the system will default to HTC USB driver instead of the microsoft USB interface driver.

Try to continue anyway with the flashing. I'm running XP and got the same thing as you, I rebooted my phone and did the procedure again, even tough I had no "green light", and it worked fine.

Related

WinMo 6.5 for Blackjack 2

Can someone plz give me a full guide on flashing it on vista because i keep getting stuck and all the guides keeps messing me up so i get even more stuck.
Foe one when i plug in my phone in downloader mode and try to update drivers it says my drivers are already up to date and when i start the image downloader i get
[StartDownload => 0] StartDownload !!
[-] Connect and Power-on the Device.
[-] Device Not Found.
Can someone plz give me a full guide
install windows mobile device center
run phone in bootloader mode
uncheck allow usb connection
connect cable to pc
manually update samsung mits usb sync with vistaruu driver (wceusbsh.inf)
then turn on your phone, accept allow usb connection and synchronize it with windows mobile device center
when synchronization is complete uncheck allow usb connection
remove usb cable, run phone in bootloader mode,start
image downloader connect usb cable and wait a moment then start flashing
VistaRUU driver: http://www.fileden.com/files/2010/1/18/2729115//VistaRUU.zip
Alright thank you I'm gonna try in a little bit and I'll post how things go
OK Good luck.
alright i finally got it to work thx for the help

[Q] ADP not working

I wanted to use nvflash to bring back to clean slate. Could not get the USB driver issue resolved in Windos 7 or XP, Read the threads, just did not work. Also noticed that the USB connect to the GTablet stopped working, it woriked fine for before trying adp. Tried Linux and the device is not seen using LSUSB did see the device is I tried via USB debugging mode. I power on and hold the vol- button see boot screen then unit goes black. No usb connect to PC either after trying.
Reset the device to stock with CWM and PC USB comes back. Is there a utility or something to check the ADP functionality at boot level, has anyone had USB issues that can help? Is it a possible hardware issue?
mrmpo said:
I wanted to use nvflash to bring back to clean slate. Could not get the USB driver issue resolved in Windos 7 or XP, Read the threads, just did not work. Also noticed that the USB connect to the GTablet stopped working, it woriked fine for before trying adp. Tried Linux and the device is not seen using LSUSB did see the device is I tried via USB debugging mode. I power on and hold the vol- button see boot screen then unit goes black. No usb connect to PC either after trying.
Reset the device to stock with CWM and PC USB comes back. Is there a utility or something to check the ADP functionality at boot level, has anyone had USB issues that can help? Is it a possible hardware issue?
Click to expand...
Click to collapse
Try USBDeview: http://www.nirsoft.net/utils/usb_devices_view.html
Disconnect the G Tablet from your PC. Then run USBDeview as administrator (i.e. right click and Run as Administrator in Windows 7). Then uninstall any drivers related to the G Tablet.
Now plug in G Tablet and it should be detected again and you can point it at a properly working ADB driver on your PC.
Have done that, but it seems that it is something on the GTablet that is causing the error. When is is malfunctioning no USB connections work and driver issues pop up, after set to factory the USB works and driver issue for storage go away.
So far I can tell that adp mode from power and vol - unroots my tab and I can not connect to pc. After re-rooting I can connect. Linux can not see device in adp mode.
Update. Returned the unit to sears for a new one and problem solved. I must of had a clinker.

SGS4G Drivers Problem?

I hope I'm posting this in the right place. I recently picked up a SGS4G and I immediately wanted to root it. When I plug my phone into the computer, however, the computer doesn't recognize it. The phone recognizes that it is plugged in (green android pops up, gives option of Kies, Media, or Mass Storage), but nothing happens on the computer end. I've downloaded about a million drivers and still no change. I've tried downloading Kies for drivers, but Kies doesn't even recognize a phone is plugged in. I've even downloaded drivers for the original Vibrant, but no luck. It's frustrating because I think that is the only reason my OneClickRoot keeps getting stuck on "waiting for device". Anyone have any ideas?
If you're using a 64 bit system, make sure you get 64 bit drivers.
Got a 64 bit system, got the 64 bit drivers. I even tried the 32 bit drivers just for the hell of it. Nada.
I dunno where you got your drivers, but here's the exact one I used.
http://dl.dropbox.com/u/38496926/usb_drivers_GalaxyS_x64.zip
I got mine from the "How to Root" thread in the SGS4G Bible thread
http://forum.xda-developers.com/showthread.php?t=1025610
I had problems with my drivers before. I downloaded Kies Mini from Samsung's site. I used Kies to install the drivers and haven't had a problem since.
Jerry D said:
I had problems with my drivers before. I downloaded Kies Mini from Samsung's site. I used Kies to install the drivers and haven't had a problem since.
Click to expand...
Click to collapse
Ditto what Jerry said. They work like a charm.
Well I finally got my computer to recognize that my phone exists, but now I keep getting a message saying that the drivers have malfunctioned. I've uninstalled and reinstalled a few times now, and no change. I can't get Kies to see my phone, or I'd try to download through it.
I'm at work so I don't have my Kies with me lol but you should be able to install the drivers. You can't do anything with Kies because the drivers aren't installed.
Look at the "options" in Kies to install drivers.
Sorry for the non technical directions. I only used Kies to install the drivers that one time.
Kies doesn't give me any option to install drivers. There isn't even an "options" tab. Even with my phone plugged in, Kies stills asks me to plug in a device. I've tried connecting my USB through Mass Storage, Media Player, and Kies. I've also tried all the above in USB debugging mode. I've even plugged it in in download mode. Still nothing. I keep getting the message that the drivers are malfunctioning.
OHHitsKB said:
Kies doesn't give me any option to install drivers. There isn't even an "options" tab. Even with my phone plugged in, Kies stills asks me to plug in a device. I've tried connecting my USB through Mass Storage, Media Player, and Kies. I've also tried all the above in USB debugging mode. I've even plugged it in in download mode. Still nothing. I keep getting the message that the drivers are malfunctioning.
Click to expand...
Click to collapse
Try this (sorry if I made this seem novice-like, but I just want to try and be clear):
Open a command prompt
type this, followed by Enter: set devmgr_show_nonpresent_devices=1
type this, followed by Enter: devmgmt
Once Device Manager opens, click View on the menu bar and select Show Hidden Devices
Expand both "Modems" & Universal Serial Bus controllers" & uninstall anything that has Samsung Android USB Composite Device, Samsung USB Composite Device, Samsung Mobile Device, Samsung Mobile Modem, etc.
Once the devices are gone, maybe reboot (probably not necessary, but why not?) and try the USB driver install again.
OHHitsKB said:
Kies doesn't give me any option to install drivers. There isn't even an "options" tab. Even with my phone plugged in, Kies stills asks me to plug in a device. I've tried connecting my USB through Mass Storage, Media Player, and Kies. I've also tried all the above in USB debugging mode. I've even plugged it in in download mode. Still nothing. I keep getting the message that the drivers are malfunctioning.
Click to expand...
Click to collapse
Ya, I didn't think there was an actual Options tab that is why I put options in quotes. I remember hitting install drivers when I installed mine months ago. It was very easy.
It sounds like you need the kind of help Steven is giving.
When you do get your computer to recognize your device I highly recommend installing the drivers through Kies. After many many flashes the have never let me down.
I wish I could be of more help. I've seen your problem in here before and our Helpful Members always get it figured out.
Best of luck!
OHHitsKB said:
Kies doesn't give me any option to install drivers. There isn't even an "options" tab. Even with my phone plugged in, Kies stills asks me to plug in a device. I've tried connecting my USB through Mass Storage, Media Player, and Kies. I've also tried all the above in USB debugging mode. I've even plugged it in in download mode. Still nothing. I keep getting the message that the drivers are malfunctioning.
Click to expand...
Click to collapse
Try USB Debugging
Oddly enough try only using the same USB port you originally installed the drivers on. I have noticed with windows 7, it tries to install the drivers when you change USB Ports, then again it should do this if they are on a separate controller.
As stated above, use USB debugging.
Hopefully we'll get you an answer that works.
Sent from my SGH-T959V using xda premium
Well, I tried Stephen's method, but still got nothing. I keep getting the error message. I just don't understand why the phone will recognize that it's plugged in, the computer will recognize that SOMETHING is plugged in, but it won't recognize WHAT.
OHHitsKB said:
Well, I tried Stephen's method, but still got nothing. I keep getting the error message. I just don't understand why the phone will recognize that it's plugged in, the computer will recognize that SOMETHING is plugged in, but it won't recognize WHAT.
Click to expand...
Click to collapse
Bummer, I Really hoped that would work. When you go into Add/Remove Programs does it show that the USB drivers are listed? If so, remove them there and re-try the installation.
stephen_w said:
Bummer, I Really hoped that would work. When you go into Add/Remove Programs does it show that the USB drivers are listed? If so, remove them there and re-try the installation.
Click to expand...
Click to collapse
I've tried that too, multiple times
I tried something different this time. In device manager, under USB Controllers, instead of deleting all the Samsung stuff, I deleted EVERYTHING (based on an idea I found on a Windows 7 help page dealing with error code 43). When I plugged my phone in, every one of the items I uninstalled reinstalled, except for "Unknown Device" (I'm assuming that's my phone), which came up failed. I'm not sure if this helps at all with diagnosing the situation, but I thought I'd throw it out there...
Did you retry Stephens suggestions after uninstalling everything?
Jerry D said:
Did you retry Stephens suggestions after uninstalling everything?
Click to expand...
Click to collapse
Yep. No dice.

[Q] Win7 system reports slow USB port when in CM Recovery

I'm loading a ROM on this Nexus S i9020A. I have unlocked the bootloader and flashed CM 5.0.2.0.
When I boot into recovery, the Windows 7 host reports "This Device Can Perform Faster" and recommends moving the phone to a different port. However all ports on the computer are USB 2 or USB 3. I have tried other ports just in case and I get the same warning.
When I try to download files with ADB PUSH, it takes forever (5-10 minutes), indicating that it is probably running at USB 1 speeds.
Windows Device Manager reports that it is using the "Android Composite ADB Interface" as the USB driver for the phone.
I have performed a ROM update using the same procedure on another Nexus S on the same computer with the same drivers, and I did not have this issue.
Why does this happen, and how can I solve it? Is there something wrong with the phone or its USB port?
As a workaround, it seems to be possible to unplug the USB cable and plug it back into the same port. In the few times I tried it, it would correctly connect at full speed. There must be some timing issue when the USB port is initialized in CM Recovery that causes the problem with Windows.

Root without PC/USB

Hi,
Have a TF101 tablet here stock rom, stock recovery...
However it seems the USB will not detect on a windows PC tried multiple cables multiple PC's tried from recovery nothing is detected in device manager at all. Tablet doesn't even detect that its connected to PC either.
Is there anyway to root this thing without USB??? I need to root it so I can install recovery and flash another rom.
Thanks,
Which Windows version are you running?
If you use Win 7 and prior you should be able to connect with the universal naked drivers manually installed from device manager
Win 8 and above need driver signing disabled or they wont install the driver and the PC wont see the TF
If you have already tried the above, you might need a new cable
http://forum.xda-developers.com/showthread.php?t=1688012
*Detection* said:
Which Windows version are you running?
If you use Win 7 and prior you should be able to connect with the universal naked drivers manually installed from device manager
Win 8 and above need driver signing disabled or they wont install the driver and the PC wont see the TF
If you have already tried the above, you might need a new cable
http://forum.xda-developers.com/showthread.php?t=1688012
Click to expand...
Click to collapse
Thanks. Well i tried windows 7 x64 and windows 8 x64, neither showed any device or unknown device in device manager... Tried multiple cables as wel, no dice...
Shouldn't MTP work regardless of drivers installed in windows 7/8 ?
Are you putting the TF into APX mode?
Connect TF to PC USB > Power Off TF > Hold Power & Volume Up until the PC recognises it (Only takes a couple seconds, nothing appears on the TF screen) then install drivers
You need APX mode for Easyflasher
For normal media transfer, it will still need to install at least some USB type driver, as do all USB devices to function, possibly not the APX drivers
Check in Developer Options > USB Debugging mode
Try it enabled and disabled with the TF plugged in
But really the MTP drivers are not what you need if you want to root. you need APX mode to work (As above)
*Detection* said:
Are you putting the TF into APX mode?
Connect TF to PC USB > Power Off TF > Hold Power & Volume Up until the PC recognises it (Only takes a couple seconds, nothing appears on the TF screen) then install drivers
You need APX mode for Easyflasher
For normal media transfer, it will still need to install at least some USB type driver, as do all USB devices to function, possibly not the APX drivers
Check in Developer Options > USB Debugging mode
Try it enabled and disabled with the TF plugged in
But really the MTP drivers are not what you need if you want to root. you need APX mode to work (As above)
Click to expand...
Click to collapse
Doesn't seem to do anything when I hold power vol+, the screen of the tablet (blank/off) and on the pc nothing is being detected.
I can get to the bootloader/recovery via holding power vol- though. Also tried USB debugging mode... nothing is detected whatsoever... ordering another cable on ebay will see if that works but I doubt it since it seems to be a common issue with this tablet (port not working with pc)
I edited my post
Nothing will appear on the TF screen in APX mode until data transfer begins
The cheap non genuine cables are renowned for data connection failing, genuine cables are recommended
I still have my original cable and it still works 100%
*Detection* said:
I edited my post
Nothing will appear on the TF screen in APX mode until data transfer begins
The cheap non genuine cables are renowned for data connection failing, genuine cables are recommended
I still have my original cable and it still works 100%
Click to expand...
Click to collapse
Using the original cable, I still can't tell if its in APX mode, installed all the drivers provided by asus, nothing is detected in windows device manager. I'm 100% its not being detected ie. no connection. I ran easyflasher anyway both sbk1 and sbk2 says it flashed recovery but it never did still the stock recovery is on the tablet.
Will try again once the new cable comes in, thanks.
Forget the ASUS drivers, use the Universal ones from the Easyflasher thread
Here's what will happen when its working as intended
When you plug the TF into the PC, no matter what mode it is in, the PC should sound the USB connect sound
When you power off the TF, then put it in APX mode, the PC will again sound the USB connect noise, then it will fail to install the correct drivers
That's when you open Device Manager, find the ! missing driver ! exclamation mark, and update drivers manually pointing it to the extracted Universal drivers
Once you have installed them, then Easyflasher should work as normal
So unless you actually have a hardware fault on the TF, or the USB ports of the PC, Id hedge my bets on the cable
Have you tried a different PC?
*Detection* said:
Forget the ASUS drivers, use the Universal ones from the Easyflasher thread
Here's what will happen when its working as intended
When you plug the TF into the PC, no matter what mode it is in, the PC should sound the USB connect sound
When you power off the TF, then put it in APX mode, the PC will again sound the USB connect noise, then it will fail to install the correct drivers
That's when you open Device Manager, find the ! missing driver ! exclamation mark, and update drivers manually pointing it to the extracted Universal drivers
Once you have installed them, then Easyflasher should work as normal
So unless you actually have a hardware fault on the TF, or the USB ports of the PC, Id hedge my bets on the cable
Have you tried a different PC?
Click to expand...
Click to collapse
Ok, well ya thats the thing no sound or detection of anything when plugging it in, or going into apx mode, rebooting etc...
I tried 2 cables and 2 different PCs. Will try a new cable but I betting that is won't work either... we'll see.
Thanks again
No need to bother with cables and drivers, just download Baidu Root: https://app.box.com/s/pyehf9fh4xem3hy50dot
EDIT: The app has built-in su access management, but I'd recommend installing SuperSU from the Play Store.
Duchman said:
No need to bother with cables and drivers, just download Baidu Root: https://app.box.com/s/pyehf9fh4xem3hy50dot
EDIT: The app has built-in su access management, but I'd recommend installing SuperSU from the Play Store.
Click to expand...
Click to collapse
THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!!! Worked to let me get TWRP installed and flashed a new rom with SU etc...
Thanks again!!!!!!!!!

Categories

Resources