Please help me out!!!! i flashed my m600 with the G4 ROM and since then i can not turn on the phone or get it into bootloader please can anyone help me out? it would be a huge help is there any way to save my spv?
I have the same prob. Did you fix it?
crossy4life said:
Please help me out!!!! i flashed my m600 with the G4 ROM and since then i can not turn on the phone or get it into bootloader please can anyone help me out? it would be a huge help is there any way to save my spv?
Click to expand...
Click to collapse
What happens when you turn the device on ? Does nothing happen or do you get a white screen or something like that?
Da9L said:
What happens when you turn the device on ? Does nothing happen or do you get a white screen or something like that?
Click to expand...
Click to collapse
Hi,
I have this problem too and I got "the nice white screen of death".
The phone's working (can recv calls) but the white screen...
The press and hold the red btn is not working in this case and I thing it could be HW problem.
Now the device is in the drawer waiting solution!
Did You find?
B.R.
George
If you can receive calls, It may be a hardware problem. Try entering bootloader to see if it still displays the white screen. If it does, try a hard reset, and if that fails, try reflashing a ROM (It shouldn't matter that you can't see what's happening on the device as you should be able to control it all from the computer).
If all that fails, I think the most likely cause is a loose connection between the screen ribbon cable and the device mainboard.
Thanks,
The white screen remains after hard reset , after reflashing rom and after changing the LCD with the working one.
The ribbon connector is prooved !
Because of the block diagram showing that CPU is directly connected to the LCD I think it could be the CPU. But if the CPU is malfunctioning the whole device must be dead!!
That is why I try to find some scheme to observe the connection but ... nothing on the net!
The other one is to change the CPU ( I have the other one not working Prophet) but at the test I could receve an error msg because of the chaged CPUs ID.
Do you have any idea what is better to do!?
Waiting
l3v5y said:
If you can receive calls, It may be a hardware problem. Try entering bootloader to see if it still displays the white screen. If it does, try a hard reset, and if that fails, try reflashing a ROM (It shouldn't matter that you can't see what's happening on the device as you should be able to control it all from the computer).
If all that fails, I think the most likely cause is a loose connection between the screen ribbon cable and the device mainboard.
Click to expand...
Click to collapse
Related
My prophet is dead...
I try to upgrade my prophet to WM6...work sucessfull
When i try install MORANGE in my prophet its error (hang)..so i try to reset.
After i push the reset button my prophet is dead...i can't do anything.
I try hard reset is still not working...i try to plug in charger -> RED LED indicator not show.
It really..really DEAD PROPHET...
Please help me with my prophet.
It still dead until now...
novian said:
My prophet is dead...
I try to upgrade my prophet to WM6...work sucessfull
When i try install MORANGE in my prophet its error (hang)..so i try to reset.
After i push the reset button my prophet is dead...i can't do anything.
I try hard reset is still not working...i try to plug in charger -> RED LED indicator not show.
It really..really DEAD PROPHET...
Please help me with my prophet.
It still dead until now...(
Click to expand...
Click to collapse
try another battery.
still not work...
dioxda2 said:
try another battery.
Click to expand...
Click to collapse
novian said:
still not work...
Click to expand...
Click to collapse
how can you hard reset?
do you really know how to?
if it still can turn on, will be recoverable...
PROPER INSTRUCTION
1. Press POWER button to off unit (if unit is ON)
2. Press CAMERA and COMM buttons simultaneously
3. While holding down CAMERA and COMM buttons, use stylus to poke the RESET button at bottom of unit.
4. Release pressing of the RESET button, and continue to hold on to CAMERA and COMM buttons until message appear on the screen asking you to press the SEND (green phone button) to continue.
thats right ?
will be recoverable ?....Oh My God..
it's really can't do anything else ?
because my prophet still can not show the light charger..still DEAD
dioxda2 said:
how can you hard reset?
do you really know how to?
if it still can turn on, will be recoverable...
Click to expand...
Click to collapse
novian said:
PROPER INSTRUCTION
1. Press POWER button to off unit (if unit is ON)
2. Press CAMERA and COMM buttons simultaneously
3. While holding down CAMERA and COMM buttons, use stylus to poke the RESET button at bottom of unit.
4. Release pressing of the RESET button, and continue to hold on to CAMERA and COMM buttons until message appear on the screen asking you to press the SEND (green phone button) to continue.
thats right ?
will be recoverable ?....Oh My God..
it's really can't do anything else ?
because my prophet still can not show the light charger..still DEAD
Click to expand...
Click to collapse
you are right, those step are very precise
so, can successfully hard reset?
PS. if the battery is not flat, please don't plug the power cable at the beginning.......
plug later when the device goes fine ( sometimes the device won't continue to boot if the power cable was plugged...
not successfully with hard reset..the prophet just blank screen...nothing else.
i try connect my prophet to pc its not detect...
how can i know the device goes fine?
for your information..if i try charge the batery (with no RED LED indicator) for may be 2 hour and then i unplug the charger...after that i try remove the batery the device show the white screen for a second like blitz...just like that.
i try insert he batery againt and doing hard reset still nothing...i plug the charger still light off...hiks...hiks...
dioxda2 said:
you are right, those step are very precise
so, can successfully hard reset?
PS. if the battery is not flat, please don't plug the power cable at the beginning.......
plug later when the device goes fine ( sometimes the device won't continue to boot if the power cable was plugged...
Click to expand...
Click to collapse
novian said:
not successfully with hard reset..the prophet just blank screen...nothing else.
i try connect my prophet to pc its not detect...
how can i know the device goes fine?
for your information..if i try charge the batery (with no RED LED indicator) for may be 2 hour and then i unplug the charger...after that i try remove the batery the device show the white screen for a second like blitz...just like that.
i try insert he batery againt and doing hard reset still nothing...i plug the charger still light off...hiks...hiks...
Click to expand...
Click to collapse
Too bad....., it does look like hardware damage.....
needs to bring to repair shop or nothing else..... good luck~~~
update condition :
my prophet if i plug usb cable..my prophet just blink-blink (white screen for a second..continue)
i press reset blink-blink STOP...but if i release reset buton blink-blink againt.
any solution for this situation ?
any one can help me ?
help!!!
i tried to upgrade to i-mate, first i unlock it using "awizard" then i use lokiwiz 02b, then i followed the instructions.. i upgrade to "ruu_prodigy_226102_22610105_022511_tmous_wwe_ship.exe" the process was so smooth until 100% but when restart, i cant boot anymore, it stucks in the scren with black and the white light on the screen keeps on blinking.. help please.. im so frustrated..
spl 2.69 g3
sorry idont remember the other info.. please, please help me..
R.I.P Dopot 818 Pro
I also have the same problem. First time I was interested with the upgrading proses by looking around the forum. They said noting would be wrong, nice display, try it. But actually the upgrading process to wm6 or wm6.1 are not stable. My Dopot 818 Pro also are now dead coursing by the upgrading from wm5 to wm6. Before upgrading I've asking around, many of the expert said do not upgrade, its not stable, but I just would listen and done the upgrading proses and that was the last time I saw my prophet functioning and its dead now..
I using a very simple basic Nokia phone now & I happy about it, I will not do the unstable upgrading again in the future..
I have the same problem, but don´t have solution :-(
I am finding the solution as well.
novian said:
update condition :
my prophet if i plug usb cable..my prophet just blink-blink (white screen for a second..continue)
i press reset blink-blink STOP...but if i release reset buton blink-blink againt.
any solution for this situation ?
Click to expand...
Click to collapse
sorry im trying to hard reset the phone too,can anybody tell me which is the COMM button,i cant find it,thanks
well?......
SicilianBoy said:
sorry im trying to hard reset the phone too,can anybody tell me which is the COMM button,i cant find it,thanks
Click to expand...
Click to collapse
Is yours a Prophet?
Should be right next to the volume slider....
Hi all... and sorry for my bad English ;-)
I've got an HTC G1. When I try to start it, nothing happens. Only the backlight turns on ... What can I do?
do you have a rooted g1 with recovery and engineering SPL?
No, it isn't rooted...
Is it brand new? I think you should be able to exchange it, if you got it from a store that is; unless you got it from online then you will have to contact the website and see where that goes.
No, it isn't brand new. Someone gave it to me... So i can't exchange it.
Try to boot it thru camera+power holding. Wont help you if success but at least will tell you where the problem.
if he can go to recover mode screen wont remain completely black as far as i know. Because splashscreen appear before recover (or other) mode starts. I might be wrong of course.
If I try to go into the recovery mode thru camera + power button, nothing happens. Only the backlight turns on (black screen with backlight & keyboard backlight...)
Follow first 6 steps in this form...
http://forum.xda-developers.com/showthread.php?t=442480
tihs should boot your G1.... then if you want go on ahead with other rooting steps to root your g1..
I tried the first 6 steps, but it won't work. I think I can't entry bootloader mode. On step #4 (...)You should see a gray/white screen with instructions(...)
nothing happens on my Phone. :S
Isn't it possible, to flash the bootloader/firmware over USB or something like that?
*push* no solution?
are you sure the phone does not boot? Does it rumble when you first turn it on?
I have a similar problemb, but my phone will completely boot and work, but the lcd does not work it stays black. i can move apps around (they rumble when you pick one up), and i can recieve calls.
I was able to get it to occasionally boot with the lcd working by rebooting the phone with call+menu+power. It worked long enough to reflash the rom to rc29, and boot into it. Then it died shortly after.
mine is going to htc.
Yes, it does rumble when I turn it on, but I think it doesn't boot. So I can't "move apps around" or "recieve calls"
And I can't use the warranty, because I'm swiss.
another way to tell if it actually boots is plug it into a pc after giviing it enough time to boot, and listen for the usb connection notification sound your phone should make.
just trying to help you narrow it down. When i am contacted by HTC i will be sure to try and get as much info from then as possible. hopefully ill get something that might help you.
Since you wont have to worry about voiding your warranty, I also suggest snagging the factory service manual and make sure all the flex cables/connectors pertaining to the lcd are properly connected. This, of course, is under the idea that you have the same problem as me.
good luck
When I plug the phone over usb into a PC, the pc find it as "HTC Android Phone USB Device".
Hmm I don't think, that the LCD is broken, because the backlight turns on... If the lcd is broken, the backlight won't turn on, right?
the backlight on mine would also stay on. then again my lcd worked intermittenly at first and proceded to work less and less, but the backlight would remain on. However, I think your problem differs from what I encountered.
The fact that your pc recognizes the phone means the usb controller is working, but thats about it... I am just trying to find out for sure if you phone boots or not. That will help narrow down the problem for sure.
Have you tried calling it from another number?
It also never hurts to take a peek at the factory service manual... if you havent already
thank you. hmm... I think I can't recieve phonecalls.. but I'm not sure. (I tried it, but yeah i don't know. xD it doesn't rumble or something like that...) Is it possible to have "remote" on the phone? So I can use it over the PC?
They have shipped my phone back. Apparently the screen dying was a side effect of the keyboard going bad...The keypad did not give me any problems though. I was told they replaced the keypad FPC (part no: 73H20137-41M, pg#102 in the service manual). They replaced nothing else.
Unforutnately they did not have any more info to give me. In your case, i would suggest opening it up and checking all the flex cable connections to ensure they are properly and fully attached. of course this check is not really for the faint of heart technically speaking, but it shouldnt be too bad with the service manual as a disassembly/assembly guide.
are there any tutorials how to open the g1? =)
http://www.youtube.com/watch?v=27inpgouXII (part I)
http://www.youtube.com/watch?v=HIg_3EgrgGY (part II)
Hey all,
I need some help. The other day my touch cruise was working fine, but I wasnt able to connect to the network, and I thought it was time to do a soft reset. After soft reset my phone has now stopped working. It is stuck on the screen that says:
POLA100
SPL-3.13.0000
CPLD-2
The screen has 4 color bars on it, in this order:
RED
GREEN
BLUE
WHITE (SERIAL OR USB)
Every time I reset the phone it quickly flashes the screen with a messege that I believe says "No Image Found"
Any ideas on how I can fix this?
Thanks for all your help guys in advance!
Matrixum
A quick update...
I have managed to get back into the phone. I plugged it into the usb, and of course it would not recognise it. However, after it was plugged in I held down the camera button, and the power button and pushed in the reset button, and vola the phone restarted back to normal. I have not lost the operating system or anything. I am not sure what will happen if I turn it off. So I plan on backing it all up and then trying to turn it off and on.
But if you have any answers to this problem please let me know as I am not sure what i have done.
Thanks again guys
Matrixum
Update:
Ok everytime I turn off my phone I go back to the tri color screen. The only way for me to get back into the phone is if I plug it into the USB and hold down the camera button and hit the soft reset. Any ideas?
I guess nobody has had this problem? I must be the first! Seriously.... Well I still have the problem, each time I shut off the phone and turn it back on it goes to the tri color screen. I have to do my combination of camera button and soft reset in order to get the phone to start properly. I dont loose any information, but the phone is now running very slugish at times.
Once again, any help would be great... Unless I am really the first one to run into this problem.
Thx,
Matrixum
Hmmm... I have no idea what could the problem be.
But I have some questions:
1. What OS is/was on your Polaris?
2. Have you managed to backup your data via ActiveSync or other means?
It looks to me like you're stuck somewhere in the upgrade process. But I'm not sure, just guessing.
I'd recommend flashing Polaris with official ROM.
Be aware that you'll lose all your data on device.
Hi,
I've flashed my phone (HTC Touch Pro) with Hardspl and then the latest Energy ROM.
Everything went perfectly and I was impressesd with how simple and easy it was and how much difference the ROM made to the phone.
Today, while using the camera, the screen went blank.
I tryed turning the phone off, pulling battery and a hard reset but its still the same.
Even after hard reset, the screen is blank but if i press the power button, on the second press, I get a flash of whats on the screen and then it goes blank again.
Should I try to reflash the phone again?
I've searched but not found the same issue
Thanks
The touch screen is still working and sometimes i can see the display, but its very dark and hard to read. Is the flex cable that needs changing?
Why would it stop working so suddenly?
Should i take it apart to reseat it?
Ok, I've found the same issue in a few other peoples phones but they seem to have beeen resolved by sendin the phone back under warantee.
I dont have that option unfortunatly so need to find a fix.
The only thing wrong with the phone is the screen backlight that suddenly failed
Can anyone help me or point me in the right direction please? I cant find a definite diagnosis anywhere
New Flex cable?
New Screen?
Pray?
Thanks
Back to stock SPL and stock ROM
Still no luck
Hello guys, I bought a new screen with frame included, and after put everything inside, the screen dont work when load Android.
Just work on splash screen, recovery or fastboot...I need help..
Even I cant see the hexagon, I tried put stock ROM..but dont work....
Led, back-home-menu buttons works, double tap work (I know because buttons works), and speakers works too....but when it load Android screen dont show anything....
Help me please...What I should to do.....sorry for my bad english..
Did you see the OnePlus logo when the phone is booting up? If not try reconnect the display connector?
soralz said:
Did you see the OnePlus logo when the phone is booting up? If not try reconnect the display connector?
Click to expand...
Click to collapse
Yes, I tried may times check everything, and seems correct....I told with seller and he get me new replacement..
Anyway im not one this happen, I checked this
https://forums.oneplus.net/threads/replacement-screen-goes-black-after-boot-logo.247230/
https://forums.oneplus.net/threads/working-phone-but-black-screen-after-the-boot-logo.315281/
Thanks!