Database Info

WiFi issue: no connection, no error (WM6)

Hello everybody
Today I updated my QTEK8310 with WM6. Everything works fine,
also GPRS (MMS and Internet).
Unfortunately, I don't get WiFi to work. It detects the SSID, then I can press
"connect". But nothing happens: no connection; no error
I tried with with WPA protection and without. Both time no success.
My laptop can connect, so the issue must be related to the phone.
Any ideas?

Sounds ridiculous, but did you reboot your phone ?

Yes, of course. --> No success.
It's realy strange. The SSID is shown, the signal strength as well.
If I press connect, I see the WiFi icon changing: dotted-circle for about 1 second, and then the circle disappears again. That's it.

Have you tried with other Wireless AP ?

Unfortunately I only have one
The only thing I can tell you is that the phone detect other
SSIDs at my place. But of course I don't have any access key.
Is there anything I can check? Any log-file or configuration setting?
Thanks!

Ok, what router are you using, if your router supports wireless G only, you might need to adjust a setting so that your phone can connect to G network at B speed
Some router, although is backward compatible with B, but the option is turned off

@karhoe
Thanks! I had to enable the "b" mode! Now it works!
It's time to try out the IP-Phone stuff... but in the
Comm-Manager I cannot activate it. Maybe I should
open a new thread for that.

Raphael: Wifi can not connect to any encrypt connection, any help?

My TouchPro can connect normally to unsecured wifi networks, but with WPA encrypted ones, it can only connect for the first time, after that it can not.
At home I have a wireless router/ADSL modem (Zoom X6) that is connected to my PC by cable, all my phones and laptops connect to internet via wifi. While other phones (1G iPhone) and laptops always connect successfully, the TP only connected once and then cannot or unable connect to the WPA security-enabled wireless network (although it's able to scan and detect the availability of the Wifi network). I tried to reset the router settings, even update router firmware, but no luck, it's still unable connect. I also tried with my office secured wifi network and I had the same problem.
Yesterday, I had to hardreset my TP and tried to connect once again, but problem was repeated, connected only once and after that, unable. Note that my previous PPC (TMobile Ameo WM5) didn't have any problem with the same wifi router and the same wifi settings (as follow).
My TP wifi settings:
Network Name: MyNetwork
Connects To: The Internet
Uncheck "This is a hidden network"
Next step:
Authentification: WPA-PSK
Data Encryption: TKIP
Greyed Out: The key is automatically provided
Network Key:************** (my pass)
Greyed Out: Key Index: 1
Next,
Checked "Use IEEE 802.1x network access control" but greyed (I can't change this)
Anybody know the solution for this issue?
Thanks and very appreciated for any help.

i experienced similar problems with my old p4350 but not yet with the TP...
no solution, sorry. but im quite unhappy that this issue still exists...

Any suggestion, pls.

yeah.. quite sucky.. I though the WiFi 'broke'.. but i was able to connect to a WEP site.. I think its something to do with WPA.
I never had this problem with my Diamond. The firmware on Diamond isso much more stable compared to Touch Pro..

I set everything to WEP and my key is open instead of shared, and now it works fine.
I had issues at my dad's, who has no encryption, and also there, when I set the key to open io shared, I got connection. (even though there is no key
anyway, it looks like that is the bug (at least in my device)

I have exactly same settings and same problem... but I want to use this encrypted connection since in future I will have to connect also in other places where I need it for sure.
Any help here?

I have similar promblem with my Hermes before.
My wireless router is running "Turbo-G" mode, my Hermes can't connect it with Turbo-G mode On.
After I change the wirless mode from Turbo-G to "g/b", my Hermes can connect it without any problem.

I tryed that and does not work...
strange is that is was working in the past and on router I did no changes but on TP I installed just some apps which should not affect this...
Only what could affect is Advanced config which I installed...
So where else can be problem?
How can I troubleshoot this?
Signal kvality is good but still keeps dropping and does not obtain IP from router.

mine works fine...not that that helps you in any way

I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.

I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...

hung_ng said:
I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.
Click to expand...
Click to collapse
You are merely restricting people from connecting to your router.. without encryption, you are sending unsecure packets all over..

Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
I tried the PT using unsecured routers, WEP and WPA and all of them worked fine with stable connectivity.
The routers I have tried (without any problems) so far are:
1. Linksys WRT-54G running Tomato firmware
2. Linksys WRT-54G running DD-WRT firmware
3. D-Link DIR-655 running latest firmware
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues...
I am not using a custom ROM.
I hope this helps in some miniscule way.
Good luck.

Minus-1 said:
Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
....
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues....
Click to expand...
Click to collapse
I was about to say the same thing...
Not having any issues with my girlfriends WPA secured router. It's on WPA2-PSK and AES encryption. Enter key first time (case sensitive!!), and of you go... Connecting without trouble ever since

hmm..Funny mine still can't connect to my home WPA2, AES or TKIP.. I'm on the Buffalo Tomato firmware..

WIFI not connecting
This solution worked for me!! Excellent. This was a right pain!
thedino said:
I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...
Click to expand...
Click to collapse

I've got the sollution, everybody on this forum probably has advance config installed, the program sets some default value's of it's own, set the WPA authentication under network in the advance config program to disabled and it will work again. Anyways, that worked for me

I've removed WiFi settings and then I edited settings again. It works now

Raphael Wifi problems
I bought this Fuze to replace my trusty Dash since I broke the antenna on my Dash. I'm running NRG Magic, but have tried other NATF and other ROMs as well, I cannot get this phone to connect to my wifi network I'm using WPA2-PSK but have disabled security for testing. My Dash and my laptop connect immediately with no problems. If I cannot get wifi going on this Fuze I'm afraid I'll have to put it on Ebay and try the Iphone, which people seem to love.
The Fuze did connect once, and it was WPA2-PSK at the time, I don't remember what ROM I was using at the time probably an NRG flavor, but Ihave had _no_ luck since.
Should I flash to 'official' ROM? Honestly I'm getting tired of playing with this thing I don't have the time.
Any help would be appreciated.
Thanks,
Marc

I may have found something
Check your time zone/daylight savings settings on your router. Phone and router time must be in sync.

02 Xda Zest Wifi problems (help)

I know there are a lot of threads about wifi problems on this site, but i cant seem to find one that has helped me.
My problem is that i am trying to connect to my orange broadband router through the wifi on the Zest. It requires a WEP key which i have, and have entered. Although my desktop PC connects to the router with the network key but uses it as a WPA-PSK key with TKIP encryption. I have also tried to connect my Zest using WPA-PSK but have been unsuccessful. It accepts the key (both as WEP and WPA-PSK) and says that the source is 'Available', but it will not actually connect to the internet. I have tried connecting to another hotspot next to my library (which does not require a key) and have been successful, it becomes available and then connects and i am able to use web browsers via wifi, as usually when i open the browser at home it automatically connects to GPRS/3G, which then costs me extra on my contract.
Any help or suggestions would be deeply appreciated.

noobish error - forgot to press the button on my router that connects new devices

FYI to other Newbies
This can also happen when the user selects (usually inadvertantly) the "WORK" option under "connects me to . . ." section in the wifi setup. When this is selected and all the other settings are set to "my device connects me to . . . 'INTERNET'", then one could have the encryption password correct and have their entire network set up correctly, but the device will STILL fail to connect. Thus, the "connection to" in the wifi network setup and the network adapter, and one's router must all "agree" or connection will not take place.

Need help, PIE or Opera will not load with Wifi

Okay for some weird reason, I have trouble opening PIE, and Opera. Iam able to connect to my router, and it does show the connected wifi icon on top.
-I have indeed disabled proxy.
-I have made Wifi slider to high performance.
-My router is set to b/g not n, and is set to Auto(WPA or WPA2), TKIP andAES.
-I also made my htc networkcard connect to internet, and set all adaptors to
server assigned.
-Oh yeah I also have disabled the router network passkey, but still could
get the same PIE error.
I spent alot of time trying to find the answer for this but nothing seems to work. If anyone has a remedy, or any suggestions please post..

settings->connections->connections->advanced->select network
is it set to my home network or whatever wifi connection and not isp connection
is called on your device?

What do u mean by home network or wifi network? The only options are medianet, at&t isp, my isp, and my work network.
If you mean my work network, I had it on the bottom selection where it says automatically connects to private network. The one on top says automatically connects to the Internet.

WiFi Connection Issues

Hello all!
Not sure if this has been posted but I figured I would put up a new post. I am showing that I am connected to my home WiFi but I am not able to actually use it. For instance, I cannot open links or watch YouTube videos. I believe it is the router because I just had a Droid RAZR and my connections to the Internet were not dependable. Currently, I am using AT&T's 2Wire 2701HG-B Gateway router.
Are there any settings that should be adjusted within the router? Encryption type is WPA-PSK. Wireless mode is 802.11g/b.
I just got my S3 yesterday and so far WiFi works in other places. Also, I tried the #*0011# thing and that did not work for me. I've rebooted and factory reset my device. Nothing helps. Anything I can change?
Thanks in advance!

Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest

ooofest said:
Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest
Click to expand...
Click to collapse
Now that I'm looking, no it doesn't have it listed there. My phone says its connoted though. I forgot the connection, rebooted the phone and did the #*0011# and reconnected the network. Still the same result. Any ideas?

I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest

ooofest said:
I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest
Click to expand...
Click to collapse
1. Yes, my iPad and two laptops.
2. There is a link speed and an IP address but the third number of the IP address on my phone is different than the third number of the IP addresses of the devices listed that connect to the router. I hope I made some type of sense saying that lol! There are about 6 devices listed that connect to the router and the first, second and third numbers are the same. My phone only have the first & second numbers in common.
3. didn't try that because I'm assuming something isn't right from the previous answer.
4. I typed in the pass phrase from my phone. I do not know of any other way to connect the device. I am not familiar with doing it from the admin panel especially since I'm not even seeing the device there.
Thanks again!

Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest

I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3

ooofest said:
Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest
Click to expand...
Click to collapse
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.

iLogikk said:
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.
Click to expand...
Click to collapse
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest

ooofest said:
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest
Click to expand...
Click to collapse
Thank you for all of your help!

Rams99 said:
I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3
Click to expand...
Click to collapse
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end

iLogikk said:
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end
Click to expand...
Click to collapse
To be honest. It's not your phone. I think you said you already did a factory reset on the modem/router correct? If not, do it and revert back to factory settings. If that doesn't work I would call att and tell them to send you another att modem/router. Tell them your wifi is down. Hopefully you'll get everything back to where it was. Good luck.
Sent from my Samsung Galaxy S3

Fix
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr! http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
I tried this part but all of my settings were already set to match this....including it because it was part of the process.
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Originally Posted by shakefry
My little sister received a cool Toshiba Thrive for Christmas but the thing will not connect to the proprietary router we have. The router isn't the problem because I've been able to connect a Macbook, 2 PCs, a 3DS and a smartphone to it and they all work as needed. When we put in the password for the connection it saying it is 'scanning' and 'connecting' then disconnects and starts going into a scanning loop saying is scanning then stopping then starting again.
I found a similar topic about this but the thread did not answer my question. I followed all of the steps of given solutions to no avail. And the constant suggestion to set the beacon or preamble differently is highly frustrating because the model router I have does not have such settings (I have gone through all the menus about ten times, literally).
I have also heard that the connection security could be a factor but I am not willing to downgrade my WPA 2 (TKIP & AES) to a WPA 1 or WEP, unless its absolutely necessary. I've been googling for hours so I need a solution or unfortunately we will have to return it for a more compatible device, which would suck because we got this for a good price (new).
Our router is a 2WIRE 3800 hgv-b (we have AT&T Uverse, idk if I should specify anything else)
Any help would be greatly appreciated.
Hi shakefry - Nice to meet you. You are 100 percent right you should not lower your security - WPA2 is the strongest and it does work fine with Thrive. That is what I use.
For some reason the ATT 2-wire routers are the most frustrating, but that is not a problem. We just might have to try a few different things, instead of getting it to connect the first time, so stay with me, OK? big brothers always have to help their little sisters...
----
1. You do not have MAC Filtering enabled,do you? If you do add the Thrive's MAC to the Router's list of permitted devices. Then try connecting.....
2. Not using MAC Filtering, or you added the thrive and still can not connect ......
OK, First ... Lets get the info your Windows Laptop has about your router when it connects
successfully to the 3800HG-B Router via wifi:
On your (Win7?) PC that is successfully connected by wifi to the same network, lets get some wifi settings. Vista - pretty much the same screens, XP a little different looking.
Click on the wifi signal lower right taskbar, open network and sharing center.
click on right side in blue, your network name
Pop up window - click on Details
the detail window opens ...
IPv4 Subnet Mask should be 255.255.255.0, if not we need to change it in the router settings.
This would prevent you from getting to the internet, but with all devices not just thrive.
Copy down IPv4 Default Gateway, and both IPv4 Servers
(Most routers will not need the actual IPv4 addresses in the devices DNS1 and DNS2, but yours might)
Now (no picture) close the DETAILS window and click on WIRELESS PROPERTIES. click on SECURITY tab, then click on SHOW PASSWORD. DO NOT CHANGE THIS FIELD, YOUR PC WILL DISCONNECT. WHAT YOU SEE IN THIS FIELD IS THE CORRECT PASSWORD TO YOUR NETWORK.
(I just want to be 100 percent sure - this is the password you need to log the thrive on. You are pretty sharp with all this stuff, so you know it is case sensitive, don't mistake a "zero" for the cap letter O, etc.
We will try using these when we set Thrive's wifi settings for your network.
(Go to link to find the screenshot)
Now please check the following router summary page by logging on to your router.
Make sure, on the right side it, shows enough DHCP Available, and on that the router
address is still 192.168.1.254
And on the left, the page is exactly the same as below, none of the blank fields are filled in, right?
And the top button is still selected ..... 192.168.1.0/255.255.255.0 (default)
--------------------------------------------------------------------------------------------------------------------------------------------------------------
THIS IS WHERE THE ACTUAL FIX CAME IN
Originally Posted by shakefry
"Would it possibly help if i DID enable filtering? then I could just put in all the device's MAC addresses and maybe it'll be more focused or something?"
No filtering wont "pull in" the devices, through the front door of the router. Filtering will just turn them around and kick them out again if they are not on the "invited to the party" List.
"edit: I just found a similar page, the design is slightly different. The router/gateway address is one number above my DHCP range and it says I have 178 available and there are 12 allocated (weird because we only have 10 devices connected to this thing that I know of)
OK so you have plenty of available IP addresses (DHCP). It is normal to see a couple more than the number of devices you have."
So now you have the info you need to connect the thrive (maybe):
1-Hold the Thrive in portrait mode so the keyboard does not hide the settings
...
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
enter 192.168.1.173. (a nice odd numbered unused ip, away from the auto assigned ones).
(You are making it an odd number (173) because if you buy, in the future, something like a network drive, or AppleTV, it will probably come with a nice "multiple of five" static number like 150 or 155 or 35
the "CONNECT" is greyed out .... right?
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
ARE YOU CONNECTED???
If NO
1- update the router's firmware - try connecting again
2- We will give up on the 3800 and add your second router, with different sets of DHCP ranges, and broadcasting on a non-conflicting channels to the 3800's channel ( channels 1, 6, and 11 do not conflict with each other - assign one router to channel one and the other to channel 11, and keep them a couple of feet away from each other.
shakefry, Please Let us know how it goes, which solution worked ... so other forum readers can help their little sisters too ....
we are standing by (actually in my comfy recliner waiting ..)
Thanks, bobj
aka Bojo, or Obi-Wan, or RouterRooter
I was able to connect to wifi consistently and access the Internet and YouTube app successfully. Hope this helps someone else!!!
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html

Glad to hear you got it going. I actually fixed mine about 3 days ago. I read somewhere changing your ssid inside the router helps. Well, I did and it actually worked. I haven't had a problem with my wifi signal yet. On mine what was happening also was whenever my phone would go into sleep for say 5min and I went to use the Internet immediately. It would take the wifi about 20-30secs for the wifi to wake up. So far, since changing my ssid I haven't had that problem at all.
Sent from my Samsung Galaxy S3

iLogikk said:
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr!
. . .
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
. . .
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
. . .
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
Click to expand...
Click to collapse
Thanks for posting a followup.
Did you delete and re-add the WiFi network on your phone, configuring it for a static route and IP address that was in the range on the router, essentially?
- ooofest