Related
I just wanted to upgrade my pda with RUU_Prophet_220734_2207114_024721(AKU2.3)_lvsw_edition.exe but I flugg out the sync cable bymistake.Now there is an screen at the opeening that show IPL SPL ect but nothing else change pda breeze at this screen what should I do ? please help me
you have to go to bootloader modus. then you can reflash your device and it should work
ndCChris said:
you have to go to bootloader modus. then you can reflash your device and it should work
Click to expand...
Click to collapse
I found the bootloader but when I tried to upgrade tthe rom there is a message as this '' no device recognized'' now what should I do
is your device in three stripes mode? if yes it should normally work to flash it
ndCChris said:
is your device in three stripes mode? if yes it should normally work to flash it
Click to expand...
Click to collapse
yes it is but computer doesn't recognize my device what should I do in this situation
cafein said:
yes it is but computer doesn't recognize my device what should I do in this situation
Click to expand...
Click to collapse
Activesync doesn't work, but if your Prophet shows USB in the lower left when you plug the USB cable, you should be able to flash it using the ROM installer.
MusicMike said:
Activesync doesn't work, but if your Prophet shows USB in the lower left when you plug the USB cable, you should be able to flash it using the ROM installer.
Click to expand...
Click to collapse
yes i shows USB but when I try to flash a rom CMD.exe screen appears and says initilazing after then device nort recognized screen appears I don't know why
You have to use an original ROM to re-flash your device. You can't flash from a ROM that uses a DOS screen
Start the ROM update as soon as your device is in three color mode!
cafein said:
yes i shows USB but when I try to flash a rom CMD.exe screen appears and says initilazing after then device nort recognized screen appears I don't know why
Click to expand...
Click to collapse
you must have a org. Rom like Qtek, O2, etc and just run the .exe file. Or if the Rom packet is already unpack then run "Romupdateutility.exe"
John-Wu said:
you must have a org. Rom like Qtek, O2, etc and just run the .exe file. Or if the Rom packet is already unpack then run "Romupdateutility.exe"
Click to expand...
Click to collapse
where can I find it can you give me a link please I need it
cafein said:
where can I find it can you give me a link please I need it
Click to expand...
Click to collapse
Use Google to search for official ROM releases of your provider..
cafein said:
where can I find it can you give me a link please I need it
Click to expand...
Click to collapse
i only have an german rom
ftp://xda:[email protected]_220739_2207119_024721_QTEK_GER_Ship.exe
mccune said:
Use Google to search for official ROM releases of your provider..
Click to expand...
Click to collapse
I searched but there is no link for it . most of the links shows XDA's ftp but it doesn't work.Shame on you Microsoft
John-Wu said:
i only have an german rom
ftp://xda:[email protected]_220739_2207119_024721_QTEK_GER_Ship.exe
Click to expand...
Click to collapse
thanks my firend I'm downloading it I hope I will solve this problem .I tnik first I will make bootscreen then plug it into usb am I right
Hi
My Uni is dead, dont enter in bootloader mode, dont upgrade, dont do nothing.
Please help me, i dont know what happen.
You have to give us more clue. What were you doing with the Universal before this happened? Were you in the process of upgrading, downloading, etc...?
cktlcmd said:
You have to give us more clue. What were you doing with the Universal before this happened? Were you in the process of upgrading, downloading, etc...?
Click to expand...
Click to collapse
I upgrade with Vista. Dont work nothing.
Solution..
Hey i had the same problem... the Screen will say Serial no. and at the bottom it will say V. 1.01
Just do one thing.... connect yr fone to a desktop with Xp and then try running the upgrader... make sure u have the Sync software with u.....
I know this because the same thing happened with me.. my fone was dead.. till i did this..
try it
danidabest said:
Hey i had the same problem... the Screen will say Serial no. and at the bottom it will say V. 1.01
Just do one thing.... connect yr fone to a desktop with Xp and then try running the upgrader... make sure u have the Sync software with u.....
I know this because the same thing happened with me.. my fone was dead.. till i did this..
try it
Click to expand...
Click to collapse
My problem is the screen dont have nothing, any letters ou numbers.
having constantly the 150 connection error message
hellonasty said:
My problem is the screen dont have nothing, any letters ou numbers.
having constantly the 150 connection error message
Click to expand...
Click to collapse
Have you tried the suggestion at least?
Look for the original ROM of your device and find a WINDOWS XP computer and try to reflash with those 2 as suggested from above.
i want Try Mamaich Method but dont recognize the usb port.
Do you know?
Thanks
hellonasty said:
i want Try Mamaich Method but dont recognize the usb port.
Do you know?
Thanks
Click to expand...
Click to collapse
I don't think it would work. The Mamaich method is for a different problem. Yours clearly is due to Windows Vista incompatibility. I had read a couple of this type of thread in the past and the only solution was already given to you.
do you know where is the original rom?
hellonasty said:
do you know where is the original rom?
Click to expand...
Click to collapse
What type of Universal do you have? TMobile, O2, IMate...etc?
Sorry
I have a qtek9000
Before I tried my 1st upgrade I download the official ROM just in case.
I thought I had it but I can't find it. I have one copy on the PC at work, but I will only return there next Wednesday, so no big help.
I remember see a post were a member informed that he had an ftp with all the ROMS. Maybe some one remember the address. If I get, it i will post it.
Cheers.
Here: http://forum.xda-developers.com/showthread.php?t=296651&highlight=official+qtek+rom
Take a look into this thread at POST #7 by nvatvani
---
cktlcmd said:
Here: ftp://ftp.xda-developers.com/Universal/Uni_AKU2_WWE/QTEK_9000/
---
Click to expand...
Click to collapse
Am I wrong or those are the files that have been deleted because M$ "request"?
ultravox said:
Am I wrong or those are the files that have been deleted because M$ "request"?
Click to expand...
Click to collapse
OOOOPPPPs. that was the wrong dead link. But I corrected it already.
dead xda
i was trying to upgrade rom downloaded from o2 for my xda 2i i have same problem as previous guy i have tried to load from windows xp machine but get connection error 101 my screen is blank apart from usb and v1.01 can anyone help?
sounds to me like it might be as simple as a dead battery.
1. what happens when you try to charge it with the wall charger?
2. have you tried switching batteries?
3. you still haven't said what you were doing with the device before this happend
4. this is totally unrelated to WM6 Forum, you shouldn't have posted this here
when you put your universal on usb with a pc on xp there is a detection? or not and are you sur that there isn t any write on the screen .
because i have the same pb in 2006 an ithink that my universal is dead an aftrer 2 day i put the universal on the light and i see v101 if you don t see to the light you don t see it because the backlight don t work.
in this case the led for the charging don t work to.
if you have this there is a solution with a free operator rom i think it s on my pc.if you need tell me
sudf said:
when you put your universal on usb with a pc on xp there is a detection? or not and are you sur that there isn t any write on the screen .
because i have the same pb in 2006 an ithink that my universal is dead an aftrer 2 day i put the universal on the light and i see v101 if you don t see to the light you don t see it because the backlight don t work.
in this case the led for the charging don t work to.
if you have this there is a solution with a free operator rom i think it s on my pc.if you need tell me
Click to expand...
Click to collapse
Thanks
It do not enter boot loader with light + power + reset and show no signs of life.
The light is off.when i push reset button flash the red light.
When connected to USB, PC reports "USB device not recognised"
I want a original rom for qtek9000 for test.
Anybody have this rom?
When I bricked my XDA Exec by means of hung program during the upgrade, I had: no reaction to normal Reset, no entry to Bootloader - basically a brick.
I did LeftSoftKey + RightSoftKey + Reset to do a *hard* reset (everything was lost anyway), and after that I could see "Serial... v1.01" Bootloader notification. When you connected that to a computer, it changed to "USB... v1.01" prompt.
So I just took JWright's image, and re-flashed it.
Guess what? It detected I had no image/extRom/RadioRom whatsoever then offered to re-flash them. I knew I'm OK when Radio upgrade progress indicator started to move.
It took me to get to another machine first, however. My Vista machine totally screwed up things, whereas my home XP managed to do the job.
Sitting on JWright's 2.02.02 now - very thoroughly made ROM, love Voice Command integrated with it instead of crappy Cyberon's software.
First of all, I wish to say thanks to jockyw2001 for coming up with a solution for all those 1.56/1.57 Tilts. You guys all got a Merry Christmas... you lucky SOBs. Haha
However, there are newer versions of the Kaiser/Tilt coming out with 1.82.00 display versions and the current fix for 1.56/1.57 do not work. They get to the WSOD and stall.
I may be one of the first to have a 1.82.00 phone - I understand that it is the latest version put out by HTC, but I won't be the last. So I am hoping that jockyw2001 reads this thread and will continue to work on finding solutions for these newer versions of the Kaiser.
@jockyw2001
I've got a bounty for you if you can figure this one out... I need to switch from Traiditonal Chinese (which my phone came with) to the WWE ROM to be able to use this phone. Thanks a bunch beforehand!
Michael
Mike some questions:
1. did you try 1.93 (i posted in the original thread)?
2. do you see tri-color with any of the versions you tried?
3. do you see "USB" on the display after a few seconds? If yes with which version?
4. do you see "unrecognized device" after unplug and replug usb cable? or do you see MS sync device in device manager?
5. do you have MTTY up and running?
Note that you should always run the SSPL with USB cable connected!!
Answer to your questions...
jockyw2001 said:
Mike some questions:
1. did you try 1.93 (i posted in the original thread)?
2. do you see tri-color with any of the versions you tried?
3. do you see "USB" on the display after a few seconds? If yes with which version?
4. do you see "unrecognized device" after unplug and replug usb cable? or do you see MS sync device in device manager?
5. do you have MTTY up and running?
Note that you should always run the SSPL with USB cable connected!!
Click to expand...
Click to collapse
A1. I did try 1.93 and I still got WSOD, I lost USB connectivity at that point
A2. No tri-color screen with 1.56, 1.93 or the original HardSPL v1
A3. I do not see "USB" anywhere, the connection goes dead at WSOD
A4. No and no.
A5. I got MTTY 1.42 and tried it, but I'm not sure I'm using it correctly. I'll have to re-read some posts for that.
Thanks for the followup. I'll try and figure out MTTY and get back to you on this.
Michael
good luck to ya..
i am sure it ll just be a matter of time before u get a solution, he is pro and before u know it u will be part of the flashing world here on xda..
the team here on xda rocks..!!
a in yul said:
i am sure it ll just be a matter of time before u get a solution, he is pro and before u know it u will be part of the flashing world here on xda..
the team here on xda rocks..!!
Click to expand...
Click to collapse
Thanks for the well wishes... I have faith in these guys based on the body of work that is available here. Almost every HTC phone ever made has been hacked so I know it's a matter of time before they get this one sorted out.
Michael
Hi dear,
I have the same problem.
During the installation of Hardspl on my new Tilt, the PDA doesn't go in Bootloader mode (3 colors screen) but stop it in a white screen......and I can only make a soft reset to continue to use it.
I have read something about these new version of Kaiser but I need to reflash my Tilt.
Is there someone who know the way to resolve this problem?
I'll post my Boot version shortly....
Thanks and regards
Daniele
I have a 1.57 (from the ROM version in Device Information, right?) Tilt that's new (stock at&t ROM without the customizations). I get the WSOD using both the methods of doing the HardSPL. I was hoping to start fooling around with my new toy!
I'll re-read the forum, but my experience seems consistent with the people in this thread.
TTFN
If I have some time left today I will post another patched SPL.
Oh yeah it *does* cost time ya know ...
You wouldn't happen to be able to pull your existing Traditional Chinese ROM off of that their badboy would you?
I'd really like getting my hands on a chinese ROM for the IME.
Please try the attached file. Follow the instructions exactly!!
The only thing I'd like to know is if display is tri-color and if "USB" appears.
Don't do anything else with it!
- download the attached file
- REMOVE SIM and SD CARDS !!
- connect usb cable
- copy sspl-1.16-test-on-kaiser.exe to your device and run it (leave usb cable connected!)
- screen should be tri-color and after a few seconds "USB" should appear on the display
display is tri-color and "USB" appears
Orange Tytn II French version HSPL 1.81
The test is ok ...
Patrick27 said:
Orange Tytn II French version HSPL 1.81
The test is ok ...
Click to expand...
Click to collapse
Thx, will wait for feedback from the original poster.
Do you actually have trouble running pof's SSPL and my SSPL 1.56 ??
re 1.81
it is ok with 1.56
Chinese ROM
ouminan said:
You wouldn't happen to be able to pull your existing Traditional Chinese ROM off of that their badboy would you?
I'd really like getting my hands on a chinese ROM for the IME.
Click to expand...
Click to collapse
I guess I'll have to go check some threads about how to dump the ROM on the Kaiser. I thought I saw an HTC traditional chinese ROM on one of the links for the Kaiser though. I'll have a look. If not, I'll do my best to dump this bad boy for you.
Michael
Hi there,
I just tried your new test file on my 1.57 Tilt and followed your instructions exactly. It worked. I get the tri-color screen and it says USB on it. It also says:
KAIS1*0
SPL-1.16.Jump
CPLD-0
Thank you for your efforts... no more WSOD!
So, is that it or is there another step? I'm not sure.
TTFN
greggerca said:
Hi there,
I just tried your new test file on my 1.57 Tilt and followed your instructions exactly. It worked. I get the tri-color screen and it says USB on it. It also says:
KAIS1*0
SPL-1.16.Jump
CPLD-0
Thank you for your efforts... no more WSOD!
So, is that it or is there another step? I'm not sure.
TTFN
Click to expand...
Click to collapse
Yes sounds like progress
With this 1.16 do you see "unrecognized device" after unplug and replug usb cable? or do you see MS sync device in device manager?
Can you also try with 1.93 from this post please.
@MikeLim: did u try?
1.16 Did not work...
jockyw2001 said:
Please try the attached file. Follow the instructions exactly!!
The only thing I'd like to know is if display is tri-color and if "USB" appears.
Don't do anything else with it!
- download the attached file
- REMOVE SIM and SD CARDS !!
- connect usb cable
- copy sspl-1.16-test-on-kaiser.exe to your device and run it (leave usb cable connected!)
- screen should be tri-color and after a few seconds "USB" should appear on the display
Click to expand...
Click to collapse
jockyw2001,
I followed your instructions to the letter but still ended up on WSOD. After about 15 seconds the USB connection times out and dies. Back to the drawing board
Michael
Just for info, I noticed this thread whilst looking for a solution to my WSOD, my Kaiser is 1.88.00.00 - (UK Orange) I used the JumpSPL1.56-kais on mine, and it worked fine, Tri-Color - USB, then installed
Also, I can tell you that so far, I have been unable to SIM-unlock via IMEI-Unlock.
MikeLim said:
jockyw2001,
I followed your instructions to the letter but still ended up on WSOD. After about 15 seconds the USB connection times out and dies. Back to the drawing board
Michael
Click to expand...
Click to collapse
After unplug and replug of the usb cable, please check if there is a microsoft usb sync device in device manager
Have you ever tried a hard reset and then run a SSPL?
jockyw2001 said:
Yes sounds like progress
With this 1.16 do you see "unrecognized device" after unplug and replug usb cable? or do you see MS sync device in device manager?
Can you also try with 1.93 from this post please.
@MikeLim: did u try?
Click to expand...
Click to collapse
Let's see... when I unplugged the USB cable and re-plugged it, Vista detected a new device and started installing a USB Sync driver. I think it finished. Actually Windows Update decided there was a new HTC Sync driver available for me, but it didn't successfully install. I'll try the next step.
TTFN
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
medeis_jar said:
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
Click to expand...
Click to collapse
Go here- http://forum.xda-developers.com/showthread.php?t=396922
And look into the force-USB Hard Spl! You may need to change your Hard Spl! Remember to use jump spl to flash!
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
redbandana said:
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
Click to expand...
Click to collapse
Hey Red, I see you got your calendar working! Yea I have never had an issue with my usb, but I saw that he flashes alot and it kinda fit the explanation for force-USB!
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
Can you get into the bootloader? Maybe reflash the ROM from bootloader mode!
I have harspl 3 56 flashed, the bootloader mode working, but windows dont reconigze my kaiser...
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
no you don't kill the processes on your mobile. you kill them in your TASK MANAGER application in windows on your pc NOT your pcc/tilt/kaiser/device then restart your computer and connect once windows is fully loaded.
edit:
These are the programs that are running on my computer associated with data sync:
1) WmdHost.exe
2) mobsync.exe
I killed proces on my computer in task menager ;] restarted and nothing happened...
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
Try uninstalling activesync on your computer then re-install it! I have heard of that working in the Herald thread!
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
ok then open Windows Mobile Device Center on your computer>Mobile Device Settings>Connection Settings>Allow USB Connections
read my first post i tryied that,...
i tryied mobile center doesnt work too...
medeis_jar said:
read my first post i tryied that,...
Click to expand...
Click to collapse
doesn't state that in your first post. It just says you never had a connection problem.
If you manually go into bootloader and have data cable connected does it say serial or usb at the bottom?
redbandana said:
doesn't state that in your first post. It just says you never had a connection problem.
Click to expand...
Click to collapse
Hey Red, happy 1000 post day! Your bigtime now!
Yes but i wroted that after flash new rom i had and tryied reinstal AS ;] sry for missunderstanding
in bootloader write usb when is connected, when i put of cable write bottom
dashmaster1000 said:
Hey Red, happy 1000 post day! Your bigtime now!
Click to expand...
Click to collapse
thanks dash and thank you for all the suggestions regarding the calender
medeis_jar said:
in bootloader write usb when is connected, when i put of cable write bottom
Click to expand...
Click to collapse
Then you are connected to your computer even though it doesnt say on computer! Go ahead and flash a new ROM! As long as your bootloader says USB you can flash!
Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!