Hello people.
Yesterday i tried to upgrade my i-mate JAMin to WM6 but i couldn't do it.
anyway, because i couldn't upgrade it to WM6, after i upgrade to 2.40 WWE when i arrived at home i've tryed to upgrade to 2.13_Portuguese_ROM...
Here was when the problem started.
When updrade started, at 1% the problem ocurred... message ERROR.
From what i've read I need a flash ROM, I'm desperate...
Can any one help to find the flash ROM and how to recover my PPC?
Best Regards
Thank's in advance.
(Faria, ajuda-me! sei que podes fazê-lo nem que seja orientando-me em português...)
where did you get 2.40 WWE
you need No Vindor ID to install the ROM
please give your IPL SPL (G3 or G4), what error message?
but your problem can be solve I'm sure, don't do anything you don't know what it is
ask before every step !!!!!!ok
Again, would people please read through the forum carefully before starting a new thread and ask the same questions over and over again. It is not that I am mean (just getting old), because any new thread will take time to read. Why not the person who need answer to read first and save other people's time. I found this forum contains so much information that most problems people generally ask are well covered one way or the other.
you may right, but human is talking here, we are not machines, human did mistakes and sometimes even if read it new people hard to get it, they need it step by step
if you don't want to help please don't reply, leave it a lone and it will go to the end with no replies
I've seen a lot of replies like yours witch they are not nice I think they have to be deleted
sorry for beeing rude, but we are human
paradis_pal said:
where did you get 2.40 WWE
you need No Vindor ID to install the ROM
please give your IPL SPL (G3 or G4), what error message?
but your problem can be solve I'm sure, don't do anything you don't know what it is
ask before every step !!!!!!ok
Click to expand...
Click to collapse
Hello paradis, and everyone else.
Thank you for you quick reply and support.
Starting to answering your questions:
- My i-mate is G3
- ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code.
About the ROM 2.40..., i'm confused and since i can't read my i-mate i don't know the correct version but it was downloaded here in this forum.
Regards
reinstall the 2.20.7.37 wwe using the NO VINDOR ID NVID
look for RUU_Prophet_220734_2207114_024721_NVID.exe you can find it here
then unlock CID see the WIKI how to
and then install any ROM you want
What is you SPL Version?
NetrunnerAT said:
What is you SPL Version?
Click to expand...
Click to collapse
this not SPL problem
the arror at 1% is becasue of changing the langauge he just need NO VINDOR ID
that is all
and I want him to unlock CID, please do my steps
If he have SPL 3.08 -> CID Unlock doesnt work -> Device report wrong DeviceID and CID ^_^
paradis_pal said:
reinstall the 2.20.7.37 wwe using the NO VINDOR ID NVID
look for RUU_Prophet_220734_2207114_024721_NVID.exe you can find it here
then unlock CID see the WIKI how to
and then install any ROM you want
Click to expand...
Click to collapse
Thank's paradis_pal
My i-mate came back to live, tank you so much.
I fallowed your instructions and the problem was solved.
Best Regards.
As i said, my i-mate is biack to life.
I try to unlock CID, but the link ftp://xda:[email protected]/Uploads/Prophet/pdamobiz.com_downgrade_and_unlockcid.rar is not working.
Can any one put it on working?
NetrunnerAT said:
If he have SPL 3.08 -> CID Unlock doesnt work -> Device report wrong DeviceID and CID ^_^
Click to expand...
Click to collapse
dear net if he has 3.08 the 2.20 will not be installed, I know what I'm writting
but thanks for the advice
I think you can find it at pdamobiz.com
but please unlock cid before doing anything
paradis_pal said:
I think you can find it at pdamobiz.com
but please unlock cid before doing anything
Click to expand...
Click to collapse
Hello.
Sorry for responding so late.
Right now my i-mate is Cid Unlocked and working with WM6 Prophet_4.0.0.0.3_PV just fine.
I´m Going to try and explore this (Beautifull) Rom and post my feedback.
Once more thank you for your help, atention and support.
Best Regards.
msylva said:
Hello.
Sorry for responding so late.
Right now my i-mate is Cid Unlocked and working with WM6 Prophet_4.0.0.0.3_PV just fine.
I´m Going to try and explore this (Beautifull) Rom and post my feedback.
Once more thank you for your help, atention and support.
Best Regards.
Click to expand...
Click to collapse
As I said before, the feedback for this rom is just... GREAT.
Better than this only if it was in Portuguese (for me, off Corse), because in these rom theres no Portuguese GPRS configurations.
Regards.
Related
Hi,
I am expecting my German XDA in the mail in the next few days.
I have been reading this forum for the past 2 weeks, and have tried to wade through all the great advice to educate myself on ROM upgrading issues. I would like to clarify that I understand this properly.
As I understand, in order to render my new XDA "O2-free" and customizable, not to mention english, I need to install a new ROM - probably the latest Imate ROM or maybe the PDAMobiz ROM.
Before I do this, should I Unlock the CID? From my reding, this will allow me to the install any ROM.
Is this an accurate understanding of everything involved?
Are there other better options to achieve my goal of a non-branded non-operator specific Jamin/Neo?
Is there a way to save my original German O2 ROM if it became necessary to return the unit for service?
I hope people do not object to thsi post. I know that it can be irritating when newbies post on topics which have already been discussed thoroughly. I have spent at least 2 weeks trying to educate myself on the procedures, and really would just like if some knowledgeable contributor could reassure me that I have not missed something obviuos.
Thanks,
Ronan
Check here
http://wiki.xda-developers.com/index.php?pagename=Prophet_Upgrades
I'm still updating the page, but its working fine for my dutch s200 (now english dopod rom)
Hi,
I tried to follow the steps as outlined, but when I get to teh first soft reset, the device locks, and I can do nothing with it!
Please tell me how to fix it. Can I use bootloader?
How?
Thanks,
Ronan
Crisis averted!
Got into bootloader and installed the dopod rom.
Ro
Dear Ro,
have you upgrated your PDA?
Can you write your procedure?
Best regards
Daniele
please, read this topic and tell me what you think about it...
http://forum.xda-developers.com/viewtopic.php?t=54878
I entered bootloader then used the Dopod ROM with the modified romupdateutility.
I have not tried anything else.
Does anyone know of a solution for us SPL 2.15.0001 users? We seem to be very restricted in options.
Ro
Please, can you write the links where it is possible to download this rom and all the necessary files?
Is there a way to save my original German O2 ROM if it became necessary to return the unit for service?
Click to expand...
Click to collapse
Here u get the official one from O2: http://www.o2online.de/o2/kunden/technikundeinst/exclusive/xda/xdaneo/index.html?nidx=1
I just upgradet to the new dopod wwe one. No probs at all with my XDA Neo. Its just 5 days old, so no CDI-unlockin needed Then I also took the O2 bootscreen again, and it works...still :wink:
Is there a way to save my original German O2 ROM if it became necessary to return the unit for service?
Click to expand...
Click to collapse
Here u get the official one from O2: http://www.o2online.de/o2/kunden/technikundeinst/exclusive/xda/xdaneo/index.html?nidx=1
I just upgradet to the new dopod wwe one. No probs at all with my XDA Neo. Its just 5 days old, so no CDI-unlockin needed Then I also took the O2 bootscreen again, and it works...still :wink:
Thanks dears,
I have updated it with Dopod rom......but now....how can I update to I-mate JAMin (italian) rom?
Does someone have an Idea to how do it?
Thanks, thanks, thanks
Daniele
Yes, you have to go to ftp.clubimate.com there you can find the JAMin ROM's and also you can choose the language you want.
As you know, first, you must CID unlock, then you can download your favorite ROM. Tell us your opinon after install it.
I have a wizzard G4....
2.16.0000
2.16.0000
What do i need to do to install faria verssion , the last one ?
Do i need to unlock ?
Thnks a Lot
You need to read alot.
galinha said:
I have a wizzard G4....
2.16.0000
2.16.0000
What do i need to do to install faria verssion , the last one ?
Do i need to unlock ?
Thnks a Lot
Click to expand...
Click to collapse
Wow! I hope this is a gag post, since coming from someone with over 200 posts I would hope you would have spent at least a few minutes reading.
If this is indeed real then I will say the following
1. GO to the G4 forum
2. Read how to unlock your G4. I have a G3 so I have paid not attention to all that hoopla.
3. Read how to install the ROM in Faria's rather long post about it.
4. Enjoy!
I tried to install on my g4, which is CIDLocked, it went through the install but didnt install the OS, the only thing that sucesfully installed was the extended rom. I then used shelltool to flash the OS, and that worked fine.
You need to read.
Great ! I will read.....Thnks for your time.
do you have a wizard or tytn? just make sure you arent flashing this on your tytn, it wont work...reason im saying this, is because you have TytN written on your sig.
I have a tytn ,
But i want to upgrade a wizard.
Thnks for your concern.
Luis
galinha said:
I have a tytn ,
But i want to upgrade a wizard.
Thnks for your concern.
Luis
Click to expand...
Click to collapse
Use the ShellTool:
http://forum.xda-developers.com/showthread.php?t=293480
All the instructions you need are here.
Or you would have to pay to have it CID unlocked (G4). Where, I don't know but supposedly people have paid for this service.
galinha said:
I have a tytn ,
But i want to upgrade a wizard.
Thnks for your concern.
Luis
Click to expand...
Click to collapse
Uh technically, the tytn is the upgrade to the Wizard...
You have a faster processor, and the capability of 3G HSDPA/UTMS data connections.
I think that currently the Wizard has better custom ROM support, although apparently Faria is moving to the Tytn so that might change (and Kyphur has been doing some good work with XDA-Live) but other than that, if I had a money tree I probably would have moved to a 8525 (Cingular Tytn).
Why are you going the opposite way? I am just curious, not trying to bash or anything...
dwny said:
Use the ShellTool:
http://forum.xda-developers.com/showthread.php?t=293480
All the instructions you need are here.
Or you would have to pay to have it CID unlocked (G4). Where, I don't know but supposedly people have paid for this service.
Click to expand...
Click to collapse
I think it is imeicheck.com
This is the new question I want to ask. (13 Aug 4.37pm London)
As mentioned in the Wizzard-wiki, there is no free way to unlock G4.
BUT !!!!! today, I just did an update (look at my signature). First of all flash the Radio and ExtRom. Then use aWizzard, enable Rapi (e),
UNLOCK CID (u) and last write new OS (w).
In the Unlock CID phase, I finally get something like "your device is successfully CID unlocked" !!!!!!!!!!!!!!!!!!!!! does this mean that my G4 is unlocked and is it the same as we pay 20 pounds to use IMEI number to lock the CID (as mentioned in wiki)??????????????????????????????
The following is the original post.
I am using a CID locked O2 XDA Mini S. It took me about 6 minute to upgrade to TNT4.0, but after that the device rebooted. And then the old wm5 shows up...... (2.21.4.1)
what's going on here?????????????
Please read the wiki before you ask questions.
jacknjill said:
Please read the wiki before you ask questions.
Click to expand...
Click to collapse
Hey, thanks for the reply. Maybe sorry for this naive question.
But I have been reading the wiki many times. Being a foreigner, I don't quite understand many terms and abbreviations in the wiki. After reading the describtion from the TNT 4.0, i know that it is safe to flash it to my O2 MiniS.
But I still don't know why it doesn't work. Here i want to ask 2 questions.
I have read the "how to flash ANY rom to a CID Locked device". 1 question I want to ask is that Any rom includes a rom like TNT4.0, right? I.E. I can flash TNT to my CID locked O2 MiniS, right?
2nd question is that, I noticed that many posts mentioned that they will need an official rom as the base. Where can I find any Official roms for the MiniS. are the following 3 the ONLY OFFICIAL roms for O2 Mini S? I apprecaite any help. Thank you.
O2 WWE OP ID 1.5.4.02 1.10.00 1.12.10 Download Thread
O2 Launch ROM WWE OP ID 1.5.4.02 1.10.00 1.12.10 Download ?Thread
O2 WWE WWE OP ID 2.21.4 2.21 2.07.10 Download Thread
wildcolor said:
Hey, thanks for the reply. Maybe sorry for this naive question.
But I have been reading the wiki many times. Being a foreigner, I don't quite understand many terms and abbreviations in the wiki. After reading the describtion from the TNT 4.0, i know that it is safe to flash it to my O2 MiniS.
But I still don't know why it doesn't work. Here i want to ask 2 questions.
I have read the "how to flash ANY rom to a CID Locked device". 1 question I want to ask is that Any rom includes a rom like TNT4.0, right? I.E. I can flash TNT to my CID locked O2 MiniS, right?
2nd question is that, I noticed that many posts mentioned that they will need an official rom as the base. Where can I find any Official roms for the MiniS. are the following 3 the ONLY OFFICIAL roms for O2 Mini S? I apprecaite any help. Thank you.
O2 WWE OP ID 1.5.4.02 1.10.00 1.12.10 Download Thread
O2 Launch ROM WWE OP ID 1.5.4.02 1.10.00 1.12.10 Download ?Thread
O2 WWE WWE OP ID 2.21.4 2.21 2.07.10 Download Thread
Click to expand...
Click to collapse
You need to use the shell tool to flash to a G4 CID locked device - follow the instructions.
dleeming said:
You need to use the shell tool to flash to a G4 CID locked device - follow the instructions.
Click to expand...
Click to collapse
Does that mean that I can flash any rom to use the shell tool, like I can flash TNT4.0 or Faria etc. ?
The answer to EVERY Question and problem you are having is:
Unlock CID your device!
For Crist sake!
You CAN NOOOOOOOOOT put any rom in your device until you have done that, and no matter whatever anyone else says , just do it, and your problems will go away...
Some poeple just dont do what the instructions tell you to do, and then fill the forum with repeated issues...
t2t said:
The answer to EVERY Question and problem you are having is:
Unlock CID your device!
For Crist sake!
You CAN NOOOOOOOOOT put any rom in your device until you have done that, and no matter whatever anyone else says , just do it, and your problems will go away...
Some poeple just dont do what the instructions tell you to do, and then fill the forum with repeated issues...
Click to expand...
Click to collapse
Man, you scaried me. But there is a post saying that I can flash any rom without CID Unlock, right? Just don't have money to do the cid unlock.
dleeming is right.
According to your signature you have got a G4 model. Follow the instructions in the stickies about upgrade of a G4 model.....
Huckleberry88 said:
dleeming is right.
According to your signature you have got a G4 model. Follow the instructions in the stickies about upgrade of a G4 model.....
Click to expand...
Click to collapse
Understand.
I just want to make sure that in theory I can flash to any roms according to thread "how to flash any rom with a cid locked"
As most of these ROM do not incl. IPL/SPL or the radio you may want to check whether your IPL/SPL and radio version work with the respective ROMs first.
If I remember correctly they require 2.x or higher IPL/SPL. But, check for yourself.
BTW what kind of Chinese support you are referring to?
The best I've used for Chinese support is CE-star specially made for WM6 release from the ppda forums. Penpower works like the transcriber for Chinese.
Monster Chinese, I have never gotten to work correctly. You can't uninstall it too.
jacknjill said:
The best I've used for Chinese support is CE-star specially made for WM6 release from the ppda forums. Penpower works like the transcriber for Chinese.
Monster Chinese, I have never gotten to work correctly. You can't uninstall it too.
Click to expand...
Click to collapse
thats interesting. What do you mean by "ppda forums"?
Some users seem to have no probs with Monster:
http://forum.xda-developers.com/showthread.php?t=314159&page=2
sorry for the OT...
Huckleberry88 said:
As most of these ROM do not incl. IPL/SPL or the radio you may want to check whether your IPL/SPL and radio version work with the respective ROMs first.
If I remember correctly they require 2.x or higher IPL/SPL. But, check for yourself.
Click to expand...
Click to collapse
Thanks mate. Now I've got my new signature. I can show this off to myself now hahahahaha
I forgot the name of the forum, but you can do a search on Leies edition of CE-star.
Idealy, I want to use the English OS system but with full Chinese support. e.g. I can install Chinese software, browse Chinese web-site etc.
But just now, I flashed a Chinese OS system. Quit happy with it now, though maybe later I will try to find a way to fullfill my ideal system above.
jacknjill said:
I forgot the name of the forum, but you can do a search on Leies edition of CE-star.
Click to expand...
Click to collapse
I see. thanks.
wildcolor said:
Idealy, I want to use the English OS system but with full Chinese support. e.g. I can install Chinese software, browse Chinese web-site etc.
But just now, I flashed a Chinese OS system. Quit happy with it now, though maybe later I will try to find a way to fullfill my ideal system above.
Click to expand...
Click to collapse
If you don't need to enter Chinese characters but just have your Wizard to show them, the easiest way would be to install a cab with the Chinese font set.
The cab is somewhere here on the forum...
Huckleberry88 said:
If you don't need to enter Chinese characters but just have your Wizard to show them, the easiest way would be to install a cab with the Chinese font set.
The cab is somewhere here on the forum...
Click to expand...
Click to collapse
Are you sure? I think this thing works similar as PC. Not only we need the font, but the encoding thing (like uni-code or something). Personally, I don't think your suggestion will work. If you find such thread, please do show it to me. It will be highly appreciated
Cheers
I am using it that way. Haven't check Chinese websites but chinese SMS and the menu of the SIM card are shown in HanZi.
check for the fontpatch.cab
or start here:
http://forum.xda-developers.com/showthread.php?t=237858&page=4&highlight=fontpatch
especially post no. 39
Cheers!
I have a locked tmobile mda... I forget what I need to do b4 I can flash a new rom... I think all I have to do is CID unlock it right? But I forget how. Any help would be great
why not to read "sticky" threads on the top!!!
cgigate said:
why not to read "sticky" threads on the top!!!
Click to expand...
Click to collapse
Yes the fastest one way to figure this out again is to read the stickies labeled unlocking and UPGRADING. That is usually pretty helpful.
help wanted
dharvey4651 said:
Yes the fastest one way to figure this out again is to read the stickies labeled unlocking and UPGRADING. That is usually pretty helpful.
Click to expand...
Click to collapse
hi ive tryd to up to wm6 but no luck ive read all the info on how to doit downloaded loads of software still no good ive managed to put wizard love rom on it for now but cant get round the cid unlocking then how to up aput wm6 on
ive tryd it but dont want to kill the phone could some one make an ruu of wm6 then upload it or dont it work that way
any help would be great please and thank you
device info
mda vario
rom ver 2.26.10.2 wwe
rom date 6/7/06
radio ver 02.25.11
protocol 4.1.13.12
ext.rom ver 2.26.10.105
i just started going to this forum and I'm just looking for a way to get WM6 on my MDA. I know there are some posts here but I don't understand a lot of this flash rom things? Could someone help me ain directing me to a trustworthy post on how to upload WM6 on my MDA? thanks!
read the stickies...
especially
How to flash a new ROM to your Wizard... a little tutorial!
VWGolf2.OHH said:
i just started going to this forum and I'm just looking for a way to get WM6 on my MDA. I know there are some posts here but I don't understand a lot of this flash rom things? Could someone help me ain directing me to a trustworthy post on how to upload WM6 on my MDA? thanks!
Click to expand...
Click to collapse
Which is your device, a G3 or G4,how come we can tell,untill and unless you do not post the vital data of your phone,no one can suggest you any help without knowing the version of your phone.always post the data.
Well 'trustworthy post on how to upload WM6 on my MDA?',why ?,do you think what all is posted here in this Forum is not Trustworthy.
Very rightly said by moseslin 'Read The Stickies',you'll find all the answers here, just "Help Yourself"
bill4676 said:
hi ive tryd to up to wm6 but no luck ive read all the info on how to doit downloaded loads of software still no good ive managed to put wizard love rom on it for now but cant get round the cid unlocking then how to up aput wm6 on
ive tryd it but dont want to kill the phone could some one make an ruu of wm6 then upload it or dont it work that way
any help would be great please and thank you
device info
mda vario
rom ver 2.26.10.2 wwe
rom date 6/7/06
radio ver 02.25.11
protocol 4.1.13.12
ext.rom ver 2.26.10.105
Click to expand...
Click to collapse
which DOC chip version you got,a G3 or G4 ? to verify post your IPL/SPL...? or download the WST Tool,install and run it and post the report to determine if it's a G3 or G4 device.You can download the WST tool here :-
http://forum.xda-developers.com/showthread.php?t=329170
If it's a G3,it's required to first CID unlock the device and than upgrade to wm6.
How to CID unlock,check this guide here :-
http://forum.xda-developers.com/showthread.php?t=285435
http://forum.xda-developers.com/showthread.php?t=263116
But if a G4,read here how to upgrade :-
http://forum.xda-developers.com/showthread.php?t=329147
Good luck
Hi , i am trying to upgrade the rom on my wizard to wm6.
some info about the pda: spl = 2.24 (Mr Clean), Pls 3.08
i am trying all the rom none of them work i can run them but they don't change my wizard.
i would like to install wm6 + touchFlo on the wizard please your help.
my e-mail : [email protected]
Thank you
CID unlock Your device.
ba_ronen, do you have brain damage?
How many people have to give you the same answer before you listen?
You posted the SAME question in the XM6R4 thread and I replied here:
http://forum.xda-developers.com/showpost.php?p=1690298&postcount=98
and you posted this thread AFTER that response.
famewolf said:
ba_ronen, do you have brain damage?
Click to expand...
Click to collapse
That's not nice...you were a n00b once too.