Related
Hello all,
Yesterday I tried to update my MDA Compact to qtek 1.06 and I saw to executables in the package:
getdevice.exe and enterbl.exe
I runned getdevice.exe for getting the device data for in the change.bat. That went oke, but out of curiosity I had to run the enterbl.exe, which made me go to the boot loader immediately. And now I'm stuck at the boot loader!
Whatever I do it won't boot to WME anymore! Soft reset, pressing the camera+power+reset, everytime it goes to the "Serial V1.00"screen.
When I remove and put back the backcover of the device (where the battery and sim are) it will go off and after a press on the power button it will boot to WME. But when I manually reset the device or when it automaticaaly reset itself after installing the ExROM tools, it goes back to the boot loader (Serial - V1.00) screen!
I even dumped the ROM with mmty to the SD card and flashed the device with that ROM again, but after it says Checksum is OK and I press reset it just goes straight to bootloader again.
I'm really out of clues of what to do. Can someone please help?
EDIT: When removing and putting back the backcover I can reset the device and it will boot back to WME so I can use it. But still when I softreset (with button or through software) it goes to boot loader. :-(
So using the backcover as a reset button is possible and does work, but it isn't very handy/usefull off course.
TIA
Regards,
Aurora13
Check the forum, the answer is there
Yes, you are still in bootloader mode and it's actually getting ready for you to flash.
Donno which part of it goes wrong, mine also have the same issue. What you need to do now is to restart your desktop pc / laptop (from the info I gathered from the forum). Then run that update thing again. This time, the same screen will appear saying it's trying to get the device data. Difference is, this time you no longer see the current version of ROM (as the Magician is in bootloader mode now). And you will see it show you the ROM that you going to upgrade to. Just follow the instruction, everything is straight forward. Hope this help.
cheers..
Thanks man!
You're the man cyberjaya!
It is working now, here is what I did (as told by cyberjaya):
- Rebooted my laptop
- Connected the MDA to the laptop
- Started the upgrade program of the qtek 1.06 ROM
- It didn't found my version, but it would let me update it to 1.06
- Flashing....(15 minutes is a LOOOONG time if you have to wait )
I did reset it a few times and it just boots normally!
Thank you ver much cyberjaya!
Regards,
Aurora13
No problemo
Am using laptop to flash also. Likely it's the USB hub thing (which listed in the "hardware devices" list). Read it somewhere, it's not recommended to flash using USB hub. Enjoy your new ROM!! .
cheers
I had a thought:
Isn't this the way to do a ROM upgrade without editing the ROM files?
Because it can't detect a different ROM and it will do the upgrade...
Or am I missing something?
Hello, I though I knowd everything I needed to upgrade my hpc from wm5 to wm6.1 with the rom of this post http://forum.xda-developers.com/showthread.php?t=401095 , so I did hard reset it, I then launched EnterBL.exe on it, I then launched ROMUpgradeUt.exe on my computer (I saw later that I should have use GetDeviceData.exe before but still, I think this wouldn't have change something), I saw that I must hard reset again my hpc, so I did and now: the screen show absolutly nothing, not "serial 6" or something but nothing, the only thing I seem to be able to do is to hard reset it again so I see the "press 0" screen but if I do so, it show me nothing again. Also, my computer doesn't recognise it. So ?
yeah I get it, I should have put the file in the right folder, not just launching it. Isn't there a way to move it now or I'm totally screwd like I can simply throw it by the window ? Even a way like paying qtek to reset it I don't know...
Woot, ok, at least now I know that I will be able to do something: I just did hit light + power + reset to enter the bootload (I'm getting a serial msg but I'm sure I will find what I'm suppose to do here since I saw help for this case many times). I understood that to go in the bootload, I had to copy the file (and since I didn't this well, I was screwed).
Fool!
You havent ROM in your UNI....Your ROM is Empty bro, cause you not upgrade correctly your UNI, you skiped a lot of steps, Do you unlock your UNI? Do you upgrade to supercid? DO you upgrade the bootloader? Do you try to upgrade the ROM with a instaler? Why you skip getdata? Do you want to brick your UNI or What?!, try to do all steps correctly and first try to back to original WM5 ROM. I did brick a UNI cause i didnt follow the steps, take care plis....
and....
Put your UNI in Bootloader, disconect usb conections in Active sync, conect the UNI, execute the installer of the ROM, if you have errors, you' ll format the UNI's RAM with mtty.exe (task 28 55aa) and try again.
I finally got the nerves to put the new radio and rom version on my HTC Touch pro.
It went wrong at 1%, and the recovery option was in a loop.
So I did exit the process after recovering/restarting like 12 times.
It did exit on a 262 error at 0% or 1%...
Ok let’s try one other rom; now I did first run the HardSPL Unsigned 190.1.3 again as advised before every rom update, and it was successful...
But when booting the phone it is stuck at the black TOUCHpro screen with the following red text at the right bottom.
R 1.02.25.19
G 52.33.25.17U
D 1.90.00.00
Now whatever I try, whatever rom version I use, it always tells me the phone is not connected by USB.
Seems like the USB driver or something is not loaded at this stage. Maybe when by some key combination I get the phone in the ROM/Boot loading menu I can try other rom version. But I could be completely on the wrong track here.
I was so happy with my WM6 phone, please help me so I can enjoy my phone again, hopefully not with the old rom and radio ofc, when possible.
Don't panic!
Put a the NBH file of the rom you want to flash on your storage card and rename it to RAPHIMG.NBH. Start the bootloader (reset and keep pressing the volume down button) and follow the directions on the screen. When it sais it flashed succesful reset again.
Of course this only work if you did install the hardspl...
Good luck,
Cheers,
Cacti
Ok found that when I go in bootloader mode manually by pressing the Volume-down and reset button at the same time it can connect to my PC.
But no matter what rom version I try, original, Stock or custom it stops at 0% or 1% .. Giving me any of these errors :
readme.doc said:
ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
Click to expand...
Click to collapse
Plz help me, I am using the original USB cable and did try a general one, no-USB hub, did remove my firewall/virus scanner software and all.
Put the NBH file on you storage card and rename it. Don't use rhe RUU...
Thanks le_cactus, the above message crossed yours..
I will try getting the new rom trough my MicroSD card, good thing I have no regular Diamond..
Diamond?
This is the HTC Touch Pro forum
Yhea I know, I have the TouchPro... aka as the Professional version of the HTC Diamond in the Netherlands.
Raphael is rarely used here, only by people who are into rom's and TF3D hacks and stuff...
Damn my CF/MD adapter does not seem to work, or my card reader, printer with card reader and my iPaq don't support 8GB cards..
Guess I have to go to the shop tomorrow for a smaller card with a new adapter or a card reader that accepts MicroSD to get my phone back to order.
Thanks for your advice and cooling down my panic moment.. "Bedankt !!!"
Thanks man for 14 euro's I did buy me a card-reader that is able to handle my 8GB microSD card and my problem is solved. Running on 405.3 with latest .28 radio drivers now.
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
bsgbelg said:
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
Click to expand...
Click to collapse
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Not possible to flash anything
what I've tried so far:
- activate active sync to install hardSPL. Not working
- install HardSPL through microSD. Not working
- install ROM through SD. Not working
I tried a non HCSD for a change, and then I see the loading scree flashing up, but quickly says No rom found and returns to the bootloader screen.
The only thing that works is load the bootloader (red green blue white) into a screen that says:
KAIS130
SPL-3.29.0000
CPLD-8
Serial
When connected to USB, it says USB, but no disk is showing in Explorer or any connection is made to AS
The only thing I've done in the past is flash the 6.1 rom through the system provided by HTC with a file called RUU_Kaiser_HTC_NLD_3.29.404.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
Please help, I really like this phone and hate to loose it
put it into bootloader, connect it to the computer and then flash one of the htc roms. make sure its an htc rom, you cant flash a custom rom cause you dont have hardspl
I have not been able to find the original rom, only the exe from htc which says Connect with active sync. Do I have to set it in bootloader and then execute the program?
Solved
Just want to let you know I sorted it out!
Flashing the original rom does not need active sync, the bootloader USB connection is sufficient.
After this, the phone restarted in 'Erasing memory' mode, but was able to finish it and reinstall the whole rom.
I believe I got the taste of it and will start testing some other roms...
msd24200 said:
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Click to expand...
Click to collapse
Thanks, worked fine
majedaly said:
Thanks, worked fine
Click to expand...
Click to collapse
good to know
**MY PHONE IS NOW WORKING***
Hey guys,
I am going to start by saying that I have read almost every single sticky, thread, wiki and anything else I could get my grubby hands on to try and solve my problem; but I fear I may have missed something, or done it wrong.
Now to my problem. My friend who had the same phone as me did a HardSPL flash a long time ago and gave me some new ROM. It worked for awhile but wasn't great so we changed to a different ROM. After awhile I got sick of this one and all of its bugs so about 3 days ago we got some with windows 6.5; unfortunately something happened; causing it to be highly unstable, so we switched AGAIN.
Now to my problem. It will not boot. If I just let it boot without doing anything *or if I hit keys* it goes to an hTc TyTn2 screen with the R; G; and D displayed. I tried to flash it via Micro sd card but all I get is a white screen with blue "loading..." and nothing; it will sit there indefinitely. I have been following cmonex's instructions to a "T" and I am stuck. I attempted to do the USB route and the phone will display the tri-colors and say USB, but my computer *Vista* isn't seeing the phone. I tried different USB ports etc. and nothing. Please let me know what you guys think; anything would be greatly appreciated.
~big3
I would recommend down-grading to xp. But if you can't try to explore the drive as a removable driver
Are you sure when you flashed it via MicroSD you had only one file named KAISIMG.nbh on the card?
This happened to me about a month ago, if it's still going to bootloader there is a good chance you can recover but the process is a bit intricate, especially to a newcomer like myself. I spent more time reading on how to fix this issue than I did on the entire process of flashing roms, mtty specifically. These are the threads I used to get running again, don't lose hope. I assure you the your answer is there.
http://forum.xda-developers.com/showthread.php?t=397157&page=4
http://forum.xda-developers.com/showthread.php?t=371154
http://forum.xda-developers.com/showthread.php?t=370169
I am sure. I even reformatted the sd card to a FAT32. It goes to a loading screen then freezes. I can also get it into the tri-color screen and have it say USB at the bottom, but when I try and flash it via USB; for some reason it starts at 0% and then crashes.
I am able to work with it in MTTY and I had to use a Task 8 command for anything to happen. I was told my friend already did a HARDSPL; is it possible that this was deleted/ corrupted?
Put your phone in bootloader mode what does it say?
Have you tried a Hard Reset yet?
Ta
Dave
hey everyone, My phone is temporarily working at this point!!!
My new question is, how do I know if my friend really put a HardSPL on my cell the first time. I know that one way to tell was through MTTY and boot command, but my cell didn't respond to that. My friend said he put a HardSPL on; would doing it again hurt anything?
big3 said:
hey everyone, My phone is temporarily working at this point!!!
My new question is, how do I know if my friend really put a HardSPL on my cell the first time. I know that one way to tell was through MTTY and boot command, but my cell didn't respond to that. My friend said he put a HardSPL on; would doing it again hurt anything?
Click to expand...
Click to collapse
Put your phone in bootloader mode and if it says "hard" next to "SPL:" it's got a hrd SPL version.
Ta
Dave
I am trying to flash a HardSPL to my phone; the computer see's the device but will not allow me to copy any files to it. When I go though the sync center, it begins to connect then says error. What should I do?
big3 said:
I am trying to flash a HardSPL to my phone; the computer see's the device but will not allow me to copy any files to it. When I go though the sync center, it begins to connect then says error. What should I do?
Click to expand...
Click to collapse
Try copying them via the SD card using a card reader if you have one.
Ta
Dave
tryd that, all it does is say loading and pretty much stays there indefinately.
Right, lets take a step back...
You don't have Hard SPL at the moment?
If not, the best guide for flashing Hard SPL is here : http://forum.xda-developers.com/showthread.php?t=433835
Follow through what mskip advises and let me know if you get stuck and at what point.
Ta
Dave
I get stuck at the very first step were you are supposed to copy the 3 different JumpSPL files. I even tried copying a word document and it said "the file Reference could not be copied. It may not exist or cannot be transferred."
My computer can access the phone, but I cannot transfer anything to its memory. I also tryed copying it to the sd card while it is in the phone and it gives me the same error. Active sync whont work either, just keeps saying error.
big3 said:
I get stuck at the very first step were you are supposed to copy the 3 different JumpSPL files. I even tried copying a word document and it said "the file Reference could not be copied. It may not exist or cannot be transferred."
My computer can access the phone, but I cannot transfer anything to its memory. I also tryed copying it to the sd card while it is in the phone and it gives me the same error. Active sync whont work either, just keeps saying error.
Click to expand...
Click to collapse
Try deleting and re-creating the partnership... Do you have Office installed, this might stop if working.
Do you have a Card Reader, put the card in there and put the files on the card that way.
Failing that MyMoblier let's you copy files, I think it works differently to AS.
Dave
i have deleted the partnership and created a new one, and it doesnt work. As for mymobiler; the website will not load for me on either my desktop or laptop.
one thing i just tryed which was interesting was to load the 3 JumpSPL files onto the sdCard and then copy them to the phone's main memory. It wouldnt allow me to do this. How do I remove the read/write protection on the phone?
big3 said:
Hey guys,
I am going to start by saying that I have read almost every single sticky, thread, wiki and anything else I could get my grubby hands on to try and solve my problem; but I fear I may have missed something, or done it wrong.
Now to my problem. My friend who had the same phone as me did a HardSPL flash a long time ago and gave me some new ROM. It worked for awhile but wasn't great so we changed to a different ROM. After awhile I got sick of this one and all of its bugs so about 3 days ago we got some with windows 6.5; unfortunately something happened; causing it to be highly unstable, so we switched AGAIN.
Now to my problem. It will not boot. If I just let it boot without doing anything *or if I hit keys* it goes to an hTc TyTn2 screen with the R; G; and D displayed. I tried to flash it via Micro sd card but all I get is a white screen with blue "loading..." and nothing; it will sit there indefinitely. I have been following cmonex's instructions to a "T" and I am stuck. I attempted to do the USB route and the phone will display the tri-colors and say USB, but my computer *Vista* isn't seeing the phone. I tried different USB ports etc. and nothing. Please let me know what you guys think; anything would be greatly appreciated.
~big3
Click to expand...
Click to collapse
did you ask this question in those threads? i just searched all your posts and im not seeing where you asked in those threads before you started a new thread.
didn't see where you tried to flash stock rom either, i recommend trying to flash it, and flash stock before you flash any cooked roms.
i never said I did any of the flashing. my friend did it all, and he claims to have done the hardspl. he then loaded new ROM onto the phone. Since he is no longer around, and everything has gone hay-wire, I am trying to fix it.
Here is my new situation; I can get the phone to fully load into the rom, but it does not have the HardSPL installed. The computer will recognize that the phone is plugged in, but active sync will not connect; just says error. If i go through "my computer" and try and copy files that way it says: "the file Reference could not be copied. It may not exist or cannot be transferred." I have tried to just re-flash it *because i really need it up and running* and the programs just say they cannot. I even used CID unlocker and it says it failed. I just don't know where to go from here.
Try doing a Hard Reset and see if your symptoms change. NOTE: Remove the SD Card.