Database Info

Black screen

Hi,
I try to change ROM from PDAMobiz Prophet WM6 V1.00 to Fantastic Mobiz XBow v1.1i. I made exactly what I was suppose to do. But after few minute i've got the error 300 "INVALID UPDATE TOOL". So I reset my S200, then it's stay on the blue page QTEK until I reset it. I try to upgrade again, but when i'm in the Bootloader mode, i connect the PDA, the letter USB appear on the PDA screen, but i've got the message "No device Connected, Would you like to try copying again", even if i still try few minutes later, it's stil say no device connected.
I don't know what can i do anymore.
Please need Help
Thanks for your help
Benjamin

What S200 you have? G3 or G4? What IPL/SPL Version?
Have you tested to use Step 2? Step 2 use a other Firmware Writer ...

G3
IPL: 2.10.0001
SPL: 2.20.0001
i don't know any other Firmware Writer. Can you tell me one please and where i can find it
thanks

ahm ... IPL/SPL with 0001 is a G4 ... have you write the G3 Firmware? if yes ... you have brick your phone!

by Brick , you mean it's definitly broken, i can do anything?
i was quit sure i used G3 version.

Do you have your dockingstation? Load your Batterie! Then try to enter the bootloader Mode! If you have black screen again ... send it back to you mobile provider and hope they exchange it.

no i don't have any dockstation.
so someone have more proposition please???

can you bring your device into bootloader screen?
from a first view it doesn't seem you bricked it (usually ipl and spl differ then (one is 0000 and one is 0001).
And as you still get an USB Icon i assume it is not broken (but i can't say that for sure).
Just try entering bootloader mode an then flash again (with a g4 firmware!) - see wiki for how to enter BL mode

Bootloader start and after power off

I've made these operations on my G4 prophet:
after to have CID unlocked the phone, I've tried to install an official italian ROM (a very good choice ), but I've trusted the man that sold me the phone.
Now powering on the phone normally, it shows the splash screen (HTC innovation) and after it power off
if start in bootloader mode (CAMERA + POWER) it shows the three colour display and IPL and SPL version (both 2.18.0001 )and after about 1 second, before to show USB enabling, it power off;
if I try an hard reset (CAMERA + COMM + POWER) it has same behaviour like in bootloader mode;
if I connect USB cable, it resets continuosly ...
Can somebody help me?

how are you cid unlocked? with a buyed tool? or some free issue?

I've cid unlocked the phone with an IMEI based paid tool

Anything to suggest? Thank you.

I don't know if I can resume my prophet so ...
do you have a sd image rom backup (complete of IPL and SPL) for G4 model or do you know where to download it ?
Thank you very much.

have you,charged the phone 100%?I mean with the normal charger,not usb.... Also download this http://forum.xda-developers.com/attachment.php?attachmentid=41869&d=1182254462
(a collection of G4 IPLs,and try to flash 2.20.0001)

Hi tonydeli7,
first thing, thank you for your help,
I will try this evening the suggested solution, but the problem is that I can't access the phone via usb.
I've erroneously upgraded the prophet (the upgrade process terminated with success) with a k-jam rom without backup before the running rom image on SD.
I'll let you know.

Nothing to do, Ihave full charged the battery phone but I 'm not able to access it via USB so that I cannot execute any upgrade by this way. Nobody has a G4 backup available on SD to try the restore?
Thank you.

I've read better the Jesterz topic about Gold Card project and I've found this other one http://forum.xda-developers.com/showthread.php?t=292667
that seems to be same problem of my phone. I'll let you know.
Thanks.

My phone is working again . Thanks.

help in jamin stop in boot loader moood

hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all

jamin G3 with SPL 2.13.0001
Hi:
Sorry my english isn't good. I'm spanish.
I read some forum but i don't read the same problem I've.
I've a imate jamin. Last sunday I installed a new rom made by Franlov (WM6.1 Clear). First i make a hardspl and installed the new rom. Well.
After i need install the original rom, but the problem now is:
Jamin KO.
Three color display and the red numbers:
IPL 2.13
SPL 2.13.0001
If I execute a romupdateutility G3, i've a error 300, invalid tool.
If I execute a romudateutility G4, i don't have error but i've the same display (three colors, etc)
I can't make a hardspl because the jamin doesn't run and msdos display says "any device connect".
CAn you help me?
I read it's possible downgrade ipl and spl making a force spl but the program i don't know if exist for jamin or s200.
THANKS
my email: [email protected]
THANKS THANKS THANKS THANKS

melmel1989 said:
hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all
Click to expand...
Click to collapse
I have the same problem! I cannot active sync as it does not connect to the device. So I cannot flash.
IPL 2.13
SPL 2.13.0000
We tried but can not find solution!
I am tired of asking for help, and nothing!

Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5

After that just follow this awsum guide by dioxda2 http://forum.xda-developers.com/showthread.php?t=353547

aia_6584 said:
Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5
Click to expand...
Click to collapse
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....

TJSM said:
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....
Click to expand...
Click to collapse
1. go to my guide, download PVtemp first ~~~~
2, force the prophet to bootloader mode, (how to? see my thread)
3. plug back to USB ( rear PC USB port please...)
4. if you see the "USB" on the left bottom Prophet screen, YOU ARE DONE!!!!
5. Flash PVtemp NOW .... delay is bad~~~~

help me about this
hi,i have a IMATE JAMIN.my phone Does'nt boot after install wm6 & other program.when it turn on display
ipl2.13.0001
spl2.13.0001
gsm02.20.21
os10.2.0.8
after display a black screen & does nothing.
and USB Does'nt recognize my device.
can you help me?

have you tried to Hard Reset the unit after flashing to WM6.1?
You can try it by pressing CAMERA + COMM Button + Reset Button (for 3 seconds)

Help needfully!!! SPV M600 (G4) bootloader mode problem

Hello everybody.
I have a htc prophet G4 (orange spv m600). After that i did a ROM flash to getting WM6 on it i'm getting a reg/green/blue screen with an ipl code and spl code.
When i put the usb in he see that, but now is coming my problem. I'm not getting into bootloader mode. What i did to get into bootlaoder mode is:
(hold the commmngr button and insert the stylus into the larger hole next to the power socket next release the styllus and hold the commmngr button)
Please wat is the thing that i'm doing wrong a tried all different combinations also with the camera button and with en without usb. I need to get into bootloader mode to getting back to WM5.
Greetz Jeronimo

hello
you may not have hardspled your device before flashing WM 6 well if you can get to bootloader mode follow this link
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
this will recover your device and if successful you will be back to windows mobile 5 ROM now if your thinking of flashing to wm6 you need to follow certain guides before flashing a new ROM
here are some:
http://forum.xda-developers.com/showthread.php?t=405384
and more if you will help yourself by searching on this forums...
hope this will help yah

problem IMATE JASJAR

How can I fix this problem, the phone does not want to enter into arrangements Booth, the problem is a program StorageManager, then it does not want to load win mobile, hard reset and give accordingly pressed 0, the phone off and nothing there, it even laptop recognized, please advice on what to do in this case, how to put it in standby Booth, so I can reinstall it.
Rom v V5.2.20931 WWE
Radio 1.14.10
Rom data-11/13/08
Protocol v-42.49.Р8
R 1.14
G 42.42.P8
0 D.07.70 RAN

problem is solved, I found the right combination of buttons, then came into phone mode flash, now works perfectly

please help!!! O2 XDA Exec - CANT OPEN
lm still in the official o2 rom wm5, but last week, l hv try to install a file "Xda_Exec_Upgrade_v1.30.162" through my computer (window 7), when i installing the file , l saw my xda exec's sceen is freeze!!!!! so l just unplug the usb cable through my computer, and soft reset my xda exec, but a worse thing happen. when it it start loading is freeze at the o2 screen with 3 line word at right down corner - ( R 1.09.00 ) , ( G 42.42.P8 ) , ( D 1.30.107 WWE ). And so strange, when l charge my exec there is no light showing, when l remove the battery the light is showing red. l hv put my battery to my friend exec it work!!!
so please help!!!!
1. screen keep freeze at o2 screen???????????
2. when remove battery, and then put it back and charge, the o2 screen come out immediately. without touch any button????? and no light showing.
3. only showing red light when remove the battery????
sorry for the poor english
please help.............

@ jeffeu : put your universal (exec) in bootloader then try to flashing (install) it again.
and do not forget to read xda-wiki -- universal (our device).

Try to activate bootloader and from there to flash, I have a problem with the Win Seven and flash only XP