Database Info

S200 Stuck in qtek screen

my s200 got stuck in the qtek screen , now i cant connect it to active sync so i can flash the rom again ! is that a way to get in the bootloader so i can flash it again , without any sort of connection of the phone to the laptop how can i flash it?

GeNoO said:
my s200 got stuck in the qtek screen , now i cant connect it to active sync so i can flash the rom again ! is that a way to get in the bootloader so i can flash it again , without any sort of connection of the phone to the laptop how can i flash it?
Click to expand...
Click to collapse
it says :
IPL : 2.10.0001
SPL : 2.15.0001
GSM : 02.30.21
OS : 10.2.0.8
... and never comes out...
it happen after i try to flash a rom to ohlala wwe wm6 2.0 rom...
Help is needed
Thx in Advance

bootloader mode
Install ActiveSync 4.5 (needed for WM6) and find out if your device is G3 or G4 before applying any of the 'Steps'.
Download ROM FantasticMobiz v1.0 and extract the files
Enter the bootloader on your device (soft-reset using stylus, while holding down the camera-button, until 3-colorscreen appears)
* Plug in the USB-cable (text 'USB' will appear in lower-left corner of the screen)
* Now execute either the ROMUpdateUtility_NV_G3.exe or ROMUpdateUtility_NV_G4.exe, located in Step1.rar.
After this, apply the rom you want to use.

Not bad for a 1st post
The guy does have a G4 (.0001 spl) hop you haven't confused him :-o
akatwinky said:
Install ActiveSync 4.5 (needed for WM6) and find out if your device is G3 or G4 before applying any of the 'Steps'.
Download ROM FantasticMobiz v1.0 and extract the files
Enter the bootloader on your device (soft-reset using stylus, while holding down the camera-button, until 3-colorscreen appears)
* Plug in the USB-cable (text 'USB' will appear in lower-left corner of the screen)
* Now execute either the ROMUpdateUtility_NV_G3.exe or ROMUpdateUtility_NV_G4.exe, located in Step1.rar.
After this, apply the rom you want to use.
Click to expand...
Click to collapse

ohlala wwe 2.0 doesnt work - I does say that if you read the whole thread :-o
GeNoO said:
it says :
IPL : 2.10.0001
SPL : 2.15.0001
GSM : 02.30.21
OS : 10.2.0.8
... and never comes out...
it happen after i try to flash a rom to ohlala wwe wm6 2.0 rom...
Help is needed
Thx in Advance
Click to expand...
Click to collapse

flykthewiz said:
Not bad for a 1st post
The guy does have a G4 (.0001 spl) hop you haven't confused him :-o
Click to expand...
Click to collapse
Yeah, I didn't realize that it was a G4. Thats a Newbie issue

NO WM6 release working on my Qtek S200, Aserg WM5 3.13 works fine

I think I have always followed the steps right, but still no succes in booting into WM6. After the hardreset it always stops on the splash screen showing the versions.
I have tried all the versions found here at xda-developers.
It is strange but when I try the ASERG 3.3.13 ROM everything is OK. I am able to boot correctly.
What could be wrong? Is it something with the SPL?
Is there a possibility to debug the boot process?
I have following versions:
IPL 2.09
SPL 2.20.0000
GSM 2.47.21
The device is CID unlocked.
Thanks for every advice.

PiGeonCZ,
Try this:
When doing flashes, usb connect using Active Sync v.4.5, connect as "guest" to sync. Windows XP only. Reboot computer once before starting.
First, very important, flash to the last official wm5 vendor rom of choice. The last I-mate, HTC/QTEK rom is fine. If you're CID unlocked & SIM unlocked, you can use any rom.
For upgrade step 1, download & use this temp rom (PDAviet Temp) to get to first:
http://forum.xda-developers.com/showthread.php?t=308266
Remember, use no other NVID rom out there for this step 1.
Upgrade Step 2: Use this rom for wm6 upgrade: Trueneytral 1.4 with MS Bluetooth stack
http://forum.xda-developers.com/showthread.php?t=302067
If this doesn't work, please let me know.

Hi DevilDuck, thanks for the reply, but no luck again.
This time with device of another my friend, also CID ulnlocked and with the same versions of IPL and SPL.
I am using WinXPSP2 ActiveSync 4.5.0
I did it in following order.
1. update RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe - succesfull
2. tab to see the align screen
3. update Prophet_PDAViet_Step1 - succesfull
4. tab to see the align screen
5. write Prophet_WM6_17913_TrueNeytral_1_4MS - succesfull
6. hardreset
7. stuck on the second splash screen again
So I have tried to write the AKU3.3.13.ASERG-us on this device too and yes it booted succesfully.
I think I have tried all possible combinations and ROMS already, but no luck with WM6.
Any idea?
thanks

Same issue
I have the same issue. I tried all available WM6 ROMs. No success. Please help!

is there a tutorial on how to upgrade to WM6?

guide here: http://forum.xda-developers.com/showthread.php?t=310452
on the second splash screen WAIT 1-2 maybe 3 minutes....

really need help

hi guys i really need your help.i had a gullum wm06 on my prophet i wanted to sell it therefore install O2 original Software.i I have a G4 O2 Prophet.Now it stucks on Bootscreen.i tried these steps to downgrade:
-----------------------------------------------------------------------
Quoted from pdamobiz site
10 steps to unlock CID of Dopod 818Pro (Prophet) with SPL 2.15
We can unlock Super CID of the device with SPL 2.15. Let's follow the steps below :
1. First, Download the unlocking program at http://files.pdamobiz.com/c/PDAMobiz..._unlockCID.rar and then unrar it to appropriate folder.
2. Full Backup the device then Hard Reset. May use Clear Storage in Setting menu.
3. After Hard Reset, tap screen to reach Align Scren page.
4. Connect USB cable to the device. ActiveSync will ask to create new partnership. Press Cancel.
5. ActiveSync connects the device as Guest.
6. Go to the folder of unlocking program. Run the file name "Downgrade.bat". Wait until the screen ask for pressing the key. Press any key and then wait wait wait for about 20 minutes. Don't disconnect USB device while in process.
7. After finishing the first process, press any key to exit. Soft Reset the device and bypass creating partnership to connect as Guest again.
8. Run file named "Unlockcid.bat". Press any key when asked and then wait for about 3 minutes. If everything is OK, the device will be unlocked. Press any key to exit.
9. Soft Reset the device again. Notice that Boot screen will show OS as 1.0.13.21
10. Now the device is CID unlocked. Users have to flash to favorite ROM. Don't use the device with this ROM. It' s purpose is for CID unlocking only. It cannot be really used.
-------------------------------------------------------------------------
My Screen shows:
IPL 2.15.0001
SPL 2.20.0001
GSM 02.47.21
OS 1.0.13.21
i need your help how can i get it running again???thx i stuck after step 7-wont reboot normally

this free unlock for G3 only, if you read the wiki you didn't attention to
Wiki said:
If you did this on a G4 model, it wil hang at the 3 color bootloader screen.
No you didn't break you phone, just upgrade to a new G4 ROM and you should be fine
Click to expand...
Click to collapse
try to install the 2.20 nvid rom

damn i am.thank you!

Upgrading WM6 ROM in Qtek9000

Hello.
I´m trying to install a new rom in my qtek, but i´m not doing with sucess.
I am a Vista Ultimate 32bits user with windows mobile device center.
The qtek is a qtek 9000.
Th rom i´m trying to install is:WM6PROBUSSINESSVC_V3 and also try other : L26 WM6 PRO Business V7 Videocall 2.
I´m trying to follow every steps in read-me files and other information in this forum. but whithout sucess.
In boot Loader, when i execute de ROMupradeUT, apears the normal window, but when i click update the program dissapers (the window), but in task manager is still running. I wait hours... No development...
When i do not do boot loader, and execute ROMupgradeUT, the window appears i click upgrade anda gives an error: ERROR 114 :ROM RADIO prblem...bla. bla..
I already do extended rom unlock...
Any ideias?
Please help!
Thanks in advance

if u have on uni orginal os and never flash this device try first unlock...remove CID
ftp://xda:[email protected]_Unlock_v1.7z
*steps in txt
sorry for my eng;/

try right clicking on each individual file of the rom - properties - run this program in compatibility mode with * and choose one of the popul that works
hope this helps
bafta si succes

I had a similar problem try removing the radio.nbf and run upgrade (I didn't put it in bootloader for this bit) then you wont get that error msg, then once the others have been installed ok (hopefully) put it in bootlaoder mode and just do the radio.
Hope this helps Dave

help in jamin stop in boot loader moood

hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all

jamin G3 with SPL 2.13.0001
Hi:
Sorry my english isn't good. I'm spanish.
I read some forum but i don't read the same problem I've.
I've a imate jamin. Last sunday I installed a new rom made by Franlov (WM6.1 Clear). First i make a hardspl and installed the new rom. Well.
After i need install the original rom, but the problem now is:
Jamin KO.
Three color display and the red numbers:
IPL 2.13
SPL 2.13.0001
If I execute a romupdateutility G3, i've a error 300, invalid tool.
If I execute a romudateutility G4, i don't have error but i've the same display (three colors, etc)
I can't make a hardspl because the jamin doesn't run and msdos display says "any device connect".
CAn you help me?
I read it's possible downgrade ipl and spl making a force spl but the program i don't know if exist for jamin or s200.
THANKS
my email: [email protected]
THANKS THANKS THANKS THANKS

melmel1989 said:
hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all
Click to expand...
Click to collapse
I have the same problem! I cannot active sync as it does not connect to the device. So I cannot flash.
IPL 2.13
SPL 2.13.0000
We tried but can not find solution!
I am tired of asking for help, and nothing!

Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5

After that just follow this awsum guide by dioxda2 http://forum.xda-developers.com/showthread.php?t=353547

aia_6584 said:
Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5
Click to expand...
Click to collapse
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....

TJSM said:
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....
Click to expand...
Click to collapse
1. go to my guide, download PVtemp first ~~~~
2, force the prophet to bootloader mode, (how to? see my thread)
3. plug back to USB ( rear PC USB port please...)
4. if you see the "USB" on the left bottom Prophet screen, YOU ARE DONE!!!!
5. Flash PVtemp NOW .... delay is bad~~~~

help me about this
hi,i have a IMATE JAMIN.my phone Does'nt boot after install wm6 & other program.when it turn on display
ipl2.13.0001
spl2.13.0001
gsm02.20.21
os10.2.0.8
after display a black screen & does nothing.
and USB Does'nt recognize my device.
can you help me?

have you tried to Hard Reset the unit after flashing to WM6.1?
You can try it by pressing CAMERA + COMM Button + Reset Button (for 3 seconds)