Hello
The camera of mine Qtek 2020 doesn't word. I don't a icon for the camera. I has gove the qtek a hard and a soft reset is do not helps. I set the new romversie on the qtek and this also don't work. Who can help me.
Thanks
Harry
Cammera Button is break
Dear All.. same prob here:
How to perform HardReset since my Camera Button is break?
Using TheGreat WM6 AKU7 from CS
May be you have to open your PDA and check what is happened with the button. Seach the manual how to open your PDA completely somewhere in here
Actually it's the caused:
I was repaired the speaker, for it is been dead; unfortunately I break the button by accident
Doesn’t have time yet for “soldering solution”, are there any other options to perform hard-reset?
makasih lhoo
I think you got the answer from another thread in WM6. You can try PSShutXP software
Nope,
been doing it ..but it doesn't show these "HardReset Menu":
-KITL
-Clear
-Format
How if you let the battery drained open the battery and wait for at least 30 minutes. normaly it is used for wm2003 but I do not know whether it work on WM5 or above
no it dont because hardreset for wm5 and wm6 require a clearing of the flash storage which never loose it after when it loose power
Related
I have a strange problem for 2 days The JAM HardReset Itself when i press power bottom or keiep it for around hour
I try to flash the rom 1.12 several times and i still have the problem
any idea please
I Mate JAM
ROM 1.12
Make sure your power button hasn't become jammed in some way. Also be sure to only press the reset button with the stylus for a few seconds in order to conduct a soft reset. The reset button could also be jammed.
What do you mean by "keep it around hour"?
Thank you for reply
1. After you install a fresh ROM, don't install anything else.
2. Remove the battery lid and make sure everything looks ok (there's a power button in there, reacting when you remove the lid).
3. Remove the SIM card and refit the lid, making sure it is 100% into place.
4. Pull the SD card and power up your device.
If you still have problems, chances are that it's hardware related and you will need the help of a service centre.
Good luck!
My JAM is second hand I open it and find a liquid probem I bought a cleaning spray I cleaned it
NOW It's working very will
Thank you HBK and Triband81 very much for reply
Good to hear that you were able to track down that problem .
Enjoy your PPC
Hello everybody:
First of all sorry for my bad English.
I try to upgrade my s100 to 1.13 (as I did before to 1.12 and was ok) but unfortunately the PC was freeze and my system stop, to solve the situation was needed a PC reset.
When I try to continue, was impossible to put the s100 to bootloader mode.
I try to remove the main battery for all night, and try with hard reset (power and reset, power + camera and reset) and with soft reset, many times but nothing. it is totally dead.
I read in the forum, that some of you had the same problem, but fortunately after remove for a long time the main battery and some hard reset the s100 star with bootloader mode, that is no my case.
Any Idea?
will be needed to send it to Qtek technical service?
Thank to all of you for the good help and the interest in improving the general knowledge
If you're absolutely sure that there is nothing on the screen, i.e. totally black then you will have to send it to the technical centre.
I had to do the same with mine one back in July.
it's nothing. pres power+camera+ reset and hold. after you will see serial and then put in usb.
Thanks for your help, but nothing in the screen.
I try many times camara+power + reset and nothing
I think that will be necesary go to the servece center.
Thanks another time.
Did you try to restart the upgrade utility after that, without touching your s100?.
It happened to me some months ago when i was upgrading to imate rom that my pc self restart,then i began the upgrading utility and it finish all the work.
If that way don't work then like the others said,you must go to service center.
Cheers mate.
record + camera + soft reset then hard reset ok
Hello I have a very strange problem with my Prophet...
when I turn it on or do a soft-reset i must touch the display and move with the stylus on the Display all the boot-time when i don´t do this my Prophet freeze at the Splash screen is that Normal ?
I have a xda Neo G4 with the Last Dopod Rom please help me anyone... sorry for my bad english and THANK YOU!!!
Did you make a HR?
Remember, you'll erase all your data. Remove the SD card and Press and hold the camara and common manager buttons at the same time, then put the stylus into the hold close to the USB connection. Still hold the mentioned button, when a dark screen become, it going to said to restore, push the green button you used to answer a call.
Your device become as factory.
cidriver said:
Did you make a HR?
Remember, you'll erase all your data. Remove the SD card and Press and hold the camara and common manager buttons at the same time, then put the stylus into the hold close to the USB connection. Still hold the mentioned button, when a dark screen become, it going to said to restore, push the green button you used to answer a call.
Your device become as factory.
Click to expand...
Click to collapse
i know how goes a hardreset Thank you no i will only know why this happens ?
I have the same problem. I only soft reset while on external power otherwise the system either hangs or I have to tap the screen often to keep it alive. I found no solution.
HELP!!!
Having the same problem here.
After hard or soft reset my prophet freezes on the screen with the spl/ipl info. This happend after I tried to install the AKU3.3.13.ASERG-us rom.
Tried everithing I know (which is not much in this area)
HELP
Try flashing with another ROM. Wm5 or wm6. We are plenty of alternatives.
reSpect
Just resetup ur Rom and other programs.... and make sure when u install any programs need to restart ur device that make restart ... and follow the steps step by step
Help! I cannot hard reset after my touch screen stopped working. Have tried pressinn gps and internet buttons, then pressing reset and keeping hold of gps and internet but device just soft resets. Would leaving the battery out do the same thing?
Alternative hard reset
Hello mate,
You say your screen isn't working but can you still use the keys and scroll wheel to navigate around the software?
If so, open the start menu and navigate to 'settings', 'system' and select 'clear storage'.
Make sure that you've removed your SD card before you do this.
It will perform a hard reset for you.
Lom
I'll try it but I think it asks you to input 1234, which I can't do without the keypad working!
Yes you do have to enter 1234 so I am totally stuck and ready to try the big hammer reset.
Can anyone help?
alternative!!
use my mobiler
this application will let u use ur ppc thru ur pc
i mean u can share n control ur ppc screen thru desktop
link
http://www.mtux.com/
Cheers Mate!
Tried what you suggested but i got a message on the screen with a yes no box to install and couldn't get the button to operate using the wheel or any hardware key!
I've put my sim card in my magician and I think I may have to send the polaris back. Bet they'll say its my fault and will want paying to fix it.
I'm going to try leaving the battery out for a while to see if that will "force" a hard reset. I know I havent bashed it as it stopped working just after a phone call which is why I think hard resetting will sort it.
Tried your suggestion on my magician: nice bit of software!
The hard reset prompt is done by the bootloader, no installed software can affect it, simply because it isn't loaded yet.
Anyway, for the unlikely case of the digitizer hardware not being reset by bootloader, try removing the battery instead of pressing the reset button. Yes, thats right, remove the battery while the unit is operating, as rude as it sounds, and reinsert it while holding the GPS + Internet buttons.
It will, of course, prompt you to enter the 1234, but the touch screen should be initialized by the bootloader. If it still wont work - RMA the unit, your digitizer is faulty.
It still wouldnt hard reset so it probably is a hardware fault. looks like its going back.
Anyone else had a similar issue?:
Sent it back to HTC in Milton Keynes where thet diagnosed a duff touchscreen and replaced it under warranty. The service was very fast and hassle free. Well done HTC!
First thing I did after sprite restore (they reload with a fresh ROM) was to install my mobiler as suggested above. No worries if the screen doesn't work now.
Thanks for your help guys!
Hello.
I have an O2 Atom with WM5.
It started for a while ago to act up.
When I used the alarm I was not able to turn it off. (The "dismiss" bottom in the lower left corner did not come up.) I tryed everything and the only thing that worked was to take out the battery and reset the whole thing.
But now the problem has developed. And I am not able to turn off the alarm at all anymore. Making the phone unusably?
Is that a known problem? If so is there anything I can do to solve it?
I have tryed to upgrade the ROM but it is allready the latest. Maybe I could upgrade it to WM6?? Is that possible? And if so how??
Best regards
settemand
i suggest you hard reset your device. to do this, hold the reset and power buttong together. a screen will show telling you to press both call and end keys (the green and red buttons). when the process is finished, see if the problem still exists. before you do a hard reset, backup any important data you may want to save.
it is also possible to upgrade to WM6, just download a ROM and follow the instructions. usually takes less than 30mins for the upgrade process.
hope this helps.
Thanks very much. That did the trick. It took some time to reinstall the backup. But it was worth it.
Regards
Settemand