Database Info

Magician problem HELP PLEASE!!!!!!!!!

My activesync can't install the magician. How can i update the rom? I try http://wiki.xda-developers.com/index.php?pagename=MagicianRomUpgrade but i can't connect to the pc. Sorry for my english. I'm from romania. Help me please!!!

Can i update rom using sd card?

Can anybody help me??? Please

Dude try re-installing Active sync..Then pick the right ROM for ur Device-and try again
Hope it works out for u.

I tried with all activsync and I can't connect. I must update rom with sd card but i don't know.

I tried with all activsync and I can't connect. I must update rom with sd card but i don't know.

Check the Wiki it has all da info u will need wit step by step info...

I can't find a rom upgrade by sd without backup. I can't make backup because my pocket can't connect to the computer

Can anybody help me?

then i think you can use another computer to upgrade your rom? just borrow your friends.... am i right?

just start ur magician in booatloader mode, and here u go. upgrade ur rom.

romupdate don't see my magician :x

re
on the pda :tick enable pc sync & select usb
than tick maintain connection
--just plug your pda in the usb & wait for to discover the pc your pda
i'm using activesync 4.1

is enable but usb device not recognized :x

I suggest you read through these two threads first. Both of them discuss in detail the procedures involved. What's important is that in ActiveSync, the option "Allow USB Connections" is unselected. Here are the links of the two threads;
http://forum.xda-developers.com/viewtopic.php?t=14973
http://forum.xda-developers.com/viewtopic.php?t=32274

Problem with HardSPL

Dear all,
Does anyone can help me with hardSPL software ?
I would like to change my ROM with the Shaps 's one...
So after having read severals topics it seems that a hardSPL is needed to unlock the current ROM.
So I have followed a tuto found on a french forum to unlock the ROM using HardSPL software.
All is running apparently well... until I have the screen with tri-color with USB wrote. Then I unplugged -replugged my TYTN II... consequence I loose the activesync connectivity... I tape ENTER.. then program is starting and is asking to have activesync connectivity for the rest of the procedure.
PS : At this stage by TYTN II appearance is still tri-color screen with USB wrote (no way to do anything on TYTN II at this moment)
My problem is that I am unable to have activesync connectivity again... I have wait for 5 or 10 minutes without success.
After severals attemps I decided to continue the program by typing NEXT... result is hardSPL is successfull.... but in the program result he doesn't give me any info on current ROM (as it is maybe supposed to provide apparently) !
Question : Is this result normal... does hardSPL worked well even if the activesync icon did not come green back ? Can I launch Shaps' s ROM installation ?
PS 2 : In case I launch Shaps 's ROM instalation on my TYTN II without having done correctly the hardSPL... does this action can break my TYTN II ?
Many thanks in advance for your help/answer.
@+ Tjojo.

you are supposed to run it wiht the activesync icon greyed out.
put your device into bootloader and if it says olipof there, then hardspl is done

XtreMe_G said:
you are supposed to run it wiht the activesync icon greyed out.
put your device into bootloader and if it says olipof there, then hardspl is done
Click to expand...
Click to collapse
Hello XtreMe_G,
many thanks for this quick answer...
Question : I did the HardSPL yesterday night... does this operation is limited in time... or can I check this day putting my device in bootloader to verify ?
Once again Mthks.
@+ Tjojo.

Tjojo said:
Hello XtreMe_G,
many thanks for this quick answer...
Question : I did the HardSPL yesterday night... does this operation is limited in time... or can I check this day putting my device in bootloader to verify ?
Once again Mthks.
@+ Tjojo.
Click to expand...
Click to collapse
i'm sorry but i really do not get what you are trying to say.
just put your device in bootloader mode, and if it says olipof there, that means you did do the hardspl correctly

XtreMe_G said:
i'm sorry but i really do not get what you are trying to say.
just put your device in bootloader mode, and if it says olipof there, that means you did do the hardspl correctly
Click to expand...
Click to collapse
Oki... just did it..
So I have Tricolor screen.... with
KAIS130
SPL-1.56.0000
CPLD-8
Serial
Does it means it did not work
@+ Tjojo.

1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop or pc via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and uncheck the option allow usb connections from microsoft activesync file connection settings replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop or pc. again Tilt will reset.
8. flash rom.
hope this helps...

Zaf said:
1. power down your Tilt and remove sd card and sim card
2. connect Tilt to laptop or pc via USB cable.
1. open "Mobile Device" folder via "Explore" button on ActiveSync.
2. copy JumpSPL1.56-KAIS.exe to the directory that it opens up to. Mine says "Mobile Device". That will be your "My Documents" directory on your Tilt.
3. use file explorer on Tilt to navigate to "My Documents" directory. Keep hitting "up" till you cant go any farther. The directory should be there.
4. Open "My Documents" and run JumpSPL1.56-KAIS.exe
5. after a few seconds "USB" appears on the display
6. unplug and uncheck the option allow usb connections from microsoft activesync file connection settings replug the usb cable.
7. run KaiserCustomRUU.exe from the flash-hardSPL directory on your laptop or pc. again Tilt will reset.
8. flash rom.
hope this helps...
Click to expand...
Click to collapse
Hello Zaf,
Mthks for this tuto... I will try it tonight when I will be at home.. currently at work without being able to close firewall & antivirus.
Thks.
@+ Tjojo.

HardSPL error
HI,
somebody help me please?
I had one TyTnII
Radio 1.27.15.32
Protocol Version: 22.51.88.13H
I try to cid unlock, but when a run HardSPL, the application show me one error: Errorcode = -2146893818, something about: invalid assign
The same thing happend when I try to install googlemaps for example.
My sim is unlock.
Have you any idea for help me?
Thanks.

mtty does not see USB port when in bootloader mode

I am stuck in bootloader mode after trying to update to tomal mobile 6.
The screen on Imate jasjar says USB at the top and V 1.01 at the bottom.
The mobile device center does not allow USB since I checked it off.
When I execute MTTY1.42 usb is not given as an option.
When I execute MTTY 0.01 I get USB as an option However when I click on it I get the message "USB port cannot open"
By the way my screen says serial originally and then USB when I connect to my usb port.
I assume that if my screen says either serial or usb that it is in boot loader mode.
This is the second time that I had this problem after trying to update using Ranju's mobile 6 upgrade.
However the first time I was able to recover by starting with the MTTY 1.42 execution

Mobile device center suggests Vista. Most people would not dare these things without using XP. Suggest you do the same and disable activesync USB connection option before using MTTY

that is my next move. Go tto a computer with XP. although I was able to execute MTTY before this on my 64 bit vista computer.
Both my home computers run Vista 32 or 64.
Could there be a physical connection problem with my USB even if serial changes to USB when I plug my device into the USB port?
It is like I have apart USB connection but not complete. Or is there a software problem in the device with the part that handles the USB port? If so is there a way out?

If your device changes from serial to usb then you can start the upgrade... 8.5 seems to be the best so for with my experience..

Are you aware that I have a non background lit screen? That the device charge light does not come on? That it does not respond to soft reset?
It only reacts to hard reset and to the insertion of the USB cable?
When I try to run MTTY which I thought that I was supposed to to clear something I get the message that it cannot find a USB port.
Given this state can I do the upgrade that you suggested? or are you assuming that my imate jasjar is fully functioning

what do you mean by .......8.5 upgrade

Okay thats sounds good so far, i have been researching about that problem you have. when the serial changes to USB thats good, it means you are ready to run the update just ignore the recognition of the usb pop up message. did you down load the 8,5 Tomal's? if so run it i will do the same this side, i have been testing the 8.71 it tereble do not use it Tomal must try to put some time on it because he forgot some of impotant features. if the device shows usb then no need for MTTY. you just run the update rom. let us know what happens. Its normal that the back light is of just upgrade. Here is the link for the 8.5 upgrade screen shots; http://forum.xda-developers.com/showthread.php?t=454906 The download link; http://vidmes.com/xda/Uni/ROMs/Tomal...WM61_20764.exe

Looks like the download link will not work just scroll down on this link and download the special build rom. (window Mobile 6.1 V8.5 Tomal) http://forum.xda-developers.com/showthread.php?t=454906

Is your memory card slot in use? Remove memory card prior to using mtty or boot loader mode.

Yes the storage card is out
the sim card is out
the device is connected to the pc
the screen on the device shows USB
I run tomal version 8.5
I get the message
error CEROM update error
then I follow the recovery instructions
on recovery I get
RUU has stopped working
eroor 101 connection error
note
someone says
"U must remove the Memory card b4 upgrade, (Very impotant)"
Does that make sense
My problems started with
I had the crossbow Mobile on the system before.
I did a system restore
then tried install tomal 8.5
and from there things went off the cliff
I am now going to try things on a XP loaded computer as a last resort

swiching to my office computer and with active sync I was able to install TOML 8.5
Problem was with vista apparently

Mtty Help me Please..
Guys,
Please help me, every time I try to use mtty, it always like this attachment. What should I do, I allready follow the instruction, but still the same.

I would try on an XP computer

I did it on XP computer.
orb3000 said:
I would try on an XP computer
Click to expand...
Click to collapse

make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?

When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
indrastrid said:
make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?
Click to expand...
Click to collapse

irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
Now, there are only two things...
1. USB Sync driver in your PC is not functioning correctly
2. You have physical problem in USB port at your device
just my two cents.

irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
set your uni in bootloader i.e. press power button + backlight and reset using your stylus.
make sure you have disabled USB connections in AS
my two cents

Stuck In BootLoader

Hi I Have Uni And Have Tomal v9 - Using Windows XP To Flash. Later I Use Windows Vista To Flash Tomal v10 I Did Not Download The Driver And Now It Is Stuck On BootLoader. The PC Know The HardWare. Please Help.

Hope this helps
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
Also have a look here to learn how to flash in vista and more usefull stuff
http://forum.xda-developers.com/showthread.php?t=567017

Thanks. Orb3000.

No prob, hope it helped

didnt help me
(MAKE SURE NOT TO USE A USB HUB).
didnt get this
and usb does not show in drop down menu (((

wasimlhr said:
(MAKE SURE NOT TO USE A USB HUB).
didnt get this
and usb does not show in drop down menu (((
Click to expand...
Click to collapse
it means yu hav to connect yur uni directly to the pc usb port, not through a hub, to avoid unwarranted disconnection. it is just a precaution and does not necessarily mean that flashing cannot be done through a hub.
as to the second query, if the mtty process is what you meant, be sure to disable usb in the activesync connection setting in order for usb prompt to appear.. cheers...

Not workign
If you are on windows 7 and are struggling with MTTY not showing USB use this - forum.xda-developers.com/showthread.php?t=540290
I think the most important things are the drivers.
Good luck

[Q] how to install a rom ?

hi ,
i wanted to ask k how to install a rom ?
i have download .nbf files (roms) and even entered to bootloader version2.01 , in o2 xda exec.
after entring to bootoader , new usb connectn appeard in pc (win7).
what should i do next ? how to install those .nbf file there...
i also downloaded a .zip which contains "UNI_ExitBootloader".
i have also unchked the "allow usb connections" , and "allow data connections when connectd to pc" when i tried to update the driver by pointing them to those zip drivers. it saya my drivers (inwin7) r up to date then those (win vista) , then i tried to sun UNI_ExitBootloader file , error occurs saying to make sure to disable the usb connections , i already unchked them
help me plz

To begin, can you specify your mobile type ?
Did you read all of the topics in its section if there was one?
Did you search a how to on google or XDA ?

N3oTraX said:
To begin, can you specify your mobile type ?
Did you read all of the topics in its section if there was one?
Did you search a how to on google or XDA ?
Click to expand...
Click to collapse
i have o2 xda exec
yes i have google it too , but still im facing that problem as described above !