Hi,
I'm just wondering if anyone can help me with this problem:
I tried to update the ROM on my O2 XDA II Mini (purchased in Australia). I downloaded the Mini ROM (May2005) from the SeeO2.com website.
When I was flashing the ROM, the process failed on Stage 1 (the Radio upgrade). It asked me to reset the phone and run it again. I ran the ROM upgrade again and it succeeded.
Upon reset of the Mini, On the Splash screen, it displayed "NO GSM". The PDA worked OK, its just that the phone function didn't.
I tried re-flashing the ROM, but encountered the Wrong Country ID error.
After researching on here, I extracted out the executable files from ROM upgrade .exe file and then downloaded the MAUpdate.exe (or something like that) from here, I started the Mini into the Bootloader mode and ran the upgrade executable. On the screen it showed the current radio version as blank.
When proceeding to flash the radio, it would hang on 0% and eventually fail.
Can anyone help?? I just want to get it working, even at the factory ROM level so I don't need to send it away for repair
Thanks for your input!
I encountered a similar porblem with radio and eventually got it to upgrade the WWE 1.12.10 ROM on the FTP. Good luck
Hi robi,
what is the link to the FTP?
When I click on your link it just goes to: http://ftp./ which fails.
I've now got another problem.
I can't turn the XDA on at all.
When I connect it to my computer via USB, the LED comes on RED.
I can't turn it on using any of the buttons, even the soft reset, hard reset or bootloader key combinations.
_kit_ said:
I've now got another problem.
I can't turn the XDA on at all.
When I connect it to my computer via USB, the LED comes on RED.
I can't turn it on using any of the buttons, even the soft reset, hard reset or bootloader key combinations.
Click to expand...
Click to collapse
LED RED means battery not exist or dead
Try to take off battery, and put it back again.
Yeah, thanks. After leaving it connected via usb for a few minutes, the LED went from Red to Orange, and I could turn it on again.
In my testing to get the Radio Stack reloaded, I took out the Radio NBF file and the other two stages of the ROM upgrade process completed successfully. When run in isolation, the Radio upgrade process still fails..
anyone has any idea about this?
yeah im having the same problem
all of a sudden my o2 XDAII mini started loading with "no GSM"
and i check my device information and there is no radio version
so when i try and update, well i guess there is nothing to update. so there is an error.
i was wondering if there was a way to install the radio fresh
voltron37 said:
yeah im having the same problem
all of a sudden my o2 XDAII mini started loading with "no GSM"
and i check my device information and there is no radio version
so when i try and update, well i guess there is nothing to update. so there is an error.
i was wondering if there was a way to install the radio fresh
Click to expand...
Click to collapse
Voltron,
I've tried different methods to try and upgrade or even reload the Radio Stack. I believe its a corruption as when I isolated the different ROMs and ran them separately, it upgraded successfully. it would show that the other components (CE and something else) were blank but that didn't stop the utility upgrading it.
I've just sent my phone off to MPS in QLD to have the ROM refreshed.
www.mpsqld.com, they are the only authorised O2 repairer in AU.
awwww
im reluctant to do so
because my phone is like two weeks out of warranty or something
so if there are other methods id prefer to do try them first
Related
Hi, I got my Qtek S200 aka Imate Jamin yesterday and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully everything on the phone was wiped out. Since there was no instruction to backup the files, I did not do it. Now all that I see is a four colored screen saying RUU in the top right corner, IPL 2.09 in the top left corner and SPL 2.09 below it.
Does anyone know how to get my phone working again? Do I have to install all the applications including windows mobile 5.0?
If yes, please tell me where to get the softwares for the Qtek S200 and info on how to install it.
Thanks in advance.....
Hi julian_me.
If you are new at this ROM updating stuff, you should use official release by the OEM from their site. Those will warn you about full battery and the need to backup your data.
Now to your problem:
You do not need to reinstall WM5 as it is part of ROM. The screen you are seeing is the bootloader. You should soft reset using the reset hole (at the bottom of the device).
If you still don't get in to windows, you should try reflashing with an official ROM.
Hi there,
Thanks for the help. I tried the soft update. It didnt work. When I checked the Qteck S200 folder from my PC I dont see any folders. It just shows up blank. Would that be an issue? Where can I get the official download of the Qtek S200 rom update? Does that bring back all the folders and programs. Sorry to be bothering you with all my questions. I am new to the pocket pc.
It's no bother, but you might be in over your head.
1) The official ROM update should be available on the QTEK site.
2) Not 'soft update' - soft reset, it doesn't update anything, it just reboots the device. Strange that it still boots to bootloader. Are you sure no buttons are pressed while the device boots?
3) You won't see anything on your PC until the device is synchronized. For that it has to boot up properly, and it seems to be stuck in bootloader.
4) If you manage to download and flash the official ROM your problem should be solved, if not you may have to send your device to the lab for repairs.
Good luck.
I have had a similar issue I think...
When the ROM upgrade ahs finished sometimes you need to remove the cable before the software resets (there is a small note on the screen to this effect). For some reason this ballses up the restart.
As levenum said - always best to download the ROM from the official website, which should provide an adobe instruction sheet too.
Hi levenum,
I tried both the soft reset and hard reset. When I did the hard reset, I got the message "Press Send to restore factory default, Other keys to quit". I pressed the send button. I get Format FAT partition. etc. When I powerup, I get the "Qtek" screen and then it goes to the bootloader screen and it gets stuck there. Any ideas??
Thanks,
Julian
cable
Have you removed the cable after the reboot?!
Yes, I did remove the cable. I also tried to reflash using the official ROM update. When I run the exe file, all that happens is that a window opens and then closes. Nothing happens after that.
re: Q-tek probs
The only time I have encountered this problem (and I have had XDA 1, II, IIi, IIs and an EXEC) is when something has been running or trying to run on the PDA as the upgrade has gone through.
If, as you say, once the download has completed you have removed the USB cable (before the reset), and no buttons are currently pressed then I do not know why the ROM isn't re-booting.
My only remaining advise would be to contact the vendor of the device and show them the problem you are having.
Re: re: Q-tek probs
I had the same issue when trying to upgrade my ROM. For some reason I were not able to use any pdamobiz ROM. I successfully switched from FR to EN using that ROM :
RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID
Now it just works fine !
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
denflorida said:
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
Click to expand...
Click to collapse
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work, Good luck
Hi, this is the first time i saw a Paki guy on this web. I know there is alot of talent in IT profession in Pakistan. Anyway its good to see u here and i got a relief that with the help of a senior member like you i can get my phone work again.
To cut the chase, I have X01HT by Softbank Japan. It is Herms200 by HTC Japanese WM5 ROM. I have installed Asukal's English MUI and it was working fine for me. Now i'm planning to visit Pakistan this month so i though to unlock the sim and i used Prof v3a to unlock. I've successfully unlocked the sim and i guess CID also. When i use some other carrier's sim, i can receive the calls but cant make the calls out coz Softbank rom has a security which comes at screen and ask for password and dont let me do anything on the PDA. After studying alot on this forum i figured that i need to change the rom to get rid of that password message. i used the Olipro's Hard SPL and got bootloader 2.10 Olipro. I checked the other necessary stuff and when satisfied i started rom update. I end up with the same message of Error 260. Now my phone has no OS and it starts at bootloader. i tried everything possible like i make sure to remove all firewalls on my PC, used all the versions of Activesync and everything possible that i could. I trust that there is nothing wrong with the ROM etc but it is with connection.
Now if i update to the original ROM, i'm afraid that it will also upgrade my Bootloader and could never be able to flash english rom. I'm really depressed for the last three days and loosing sleep as well. I trust that you or any other senior member can help me with this.
Thanks in advance and looking forward anxiously.
Farrukh, wrong forum.
You know you have a Hermes, then you should know to post your questions in Hermes related forum, not wizard.
denflorida:
Try to update other Radio-only ROMs in xda's FTP server.
Sorry Brother, i know i have herms but i couldn't find some related topic in herms and i figured that Activesync problem is the same in all devices.
Anyway, thanks for the prompt reply. I'll try to find some from Herms.
Thanks
8125 rom update
i have tried to do a rom update on my 8125 g4. i recently purchased it off ebay and i have two problems. the reason i want to update it is because when i try to enable the wifi my device freezes. the other problem is that i can not seem to get the phone into boot loader mode. i have tried :
-turning the phone off and holding the camera button as i turn it on.
-holding the camera button and pluging it in to a usb port.
- using wizard service tool to enter boot loader mode.
after each of these different attempts i had to either remove the battery for 3 secs or hold the reset button for a few seconds before i can turn it back on. the phone still turns and just i can not use the wifi
Yes!!! Thank you! your instructions worked for me and got me past the Error [260] with my 8125 .
zabardast_1 said:
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
Click to expand...
Click to collapse
Thanks! Worked for Topaz and latest radio update.
Hi to all,
I have an AT&T TILT HTC 8925,
ROM: 1.57.502.2
RADIO: 1.27.12.11
VE: 22.45.88.07H
Installed the kaiser-HardSPLv1 with no problems.
After this I Flashed (via USB) Q-Mobile_v1.2 ROM, that went perfect. Made a soft reset and then a Hard Reset after this I configured the phone.
After everything was working I made a Radio flash with KAIS Radio Only 1.27.12.17 CustomRUU, all seemed normal until it got to 95%, it suddenly interrupted the update (error 262), and took me to recovery dialog 1-4 steps which I did.
From that moment until know I get the tricolor screen with the following text:
RUUNBHKAIS 1*0
SPL-1.56.0000
CPLD-8
USB
Click to expand...
Click to collapse
And when I try to flash ANY ROM, It gets past the tricolor screen, to a white screen with a percentage bar that gets to 0%, after a minute or so the customRUU screen goes to error 262 and I get to the recovery screen, etc...
I run on WinXP SP2, and have already tried several roms with the same result, with the exception of original ATT RUU_Kaiser_CINGULAR_WWE_.exe, it then gets to 1% and displays error code 294 Invalid Vendor ID.
When I tried the MicroSD method with the rom it gets to the tricolor then the "Loading..." screen, and keeps there (I waited for about 30 min)...
There was no SIM or MicroSD card on the phone at the moment of flashing, and I did dump the original ROM to the 4 raw parts as per instructions.
I live waaay out of the countries with AT&T or HTC servicing routes, so I am stuck with it until I fix it, which I know I can do, and to be honest with myself, can't afford to waste the money spent on this thing.
Until now the best similar thing I found about this was with the hermes unbrick phone thread, and I am not sure this works on the KAISER, but to be honest, I get cold sweats to use any more procedures (without reconfirmation) on this as I have a phone that at least still shows "some" signs of life.
After reading days of threads (my eyes are burning) I know the knowledge is within this site, but I need guidance since I am new to this thing (smartphone flashing) although familiar with computers.
Any kind of help will be very appreciated and valued.
Best Regards.
----------------------
As an update, I solved this thing. Thanks for your help.
After seeing that there was some sort of problem with the boot mode screen not showing the kaiser-HardSPL data, I went in that direction. After some suggestions and much trying I decided to download all / any original roms I found in here for my phone (ATT Tilt) then I worked my way from top to bottom based on the versions of the radio.
The one that solved my problem was 1.5.502.3 Radio 1.27.12.11 although strangely it shows on my phone after the successful flashing. 1.5.502.1
Just out of curiosity I went and installed again kaiser-HardSPLv1 and it gets to this text on tricolor screen:
Kais1*0
SPL-.JumpSPL
CPLD-8
Doing a hard reboot (camera button + soft reset) gives me a different screen:
Kais1*0
SPL - 1.56.0000
CPLD-8
Really don't know if this is normal, and after flashing a cooked rom I had to reinstall it (kaiser-HardSPL).
I have now reflashed QMobile rom and have no problems. Although I didn't flashed again new radios
For flashing the Original rom I did make sure of the following steps in addition to normal ones (Just in case)
1) Disconnected fisically from LAN (Unplugged LAN Cable)
2) Disabled all firewall protections
3) Disabled all antivirus and spyware protections
4) Run RUU original files
5) Pray
Thanks again people
I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/
I just tried it again (See I am not so scared anymore), and received the same results (Radio upgrade fails on 95%).
I have burned the original ROM back and all is well again!
I also can't get past the same screen and try as I might Activesync won't recognise the phone. When going through the recovery process on Kaiser Custom RUU it says its recovered but then when trying to go through the update it sticks on 0% and then says there are communication problems etc.
On the tricloloured screen it says
KAIS130
SPL-1.81.0000
CPLD-8
Will a hard reset do anything?
Any help much appreciated.
Bump
Now managed to boot via MTTY but power off etc returns me to bootloader screen
Looks to me like you guys have had problems flashing hardspl. Your tri-colour screen should have:
KAIS130 MFG (or Kais 120 etc)
SPL-1.0OliPof
CPLD-8
I don't know about the CPLD number but you MUST have the OliPof SPL. Check this after running hardSPL to make sure that it's there before flashing another ROM.
If you have this but still get trouble flashing, try going to the tri-colour screen and then run the kaiser_RUU.exe to upgrade.
http://forum.xda-developers.com/sho...ked. (One without a radio)
- Flash a radio...
i had the same thing with my MDA Vario 3,but with no success finding the original ROM, since I`m from a small country. I`ve tried to reboot to normal screen via MTTY but it gives me the error: Command error . So - now I`m left with two options: to dump and reconstruct an original ROM from the same type of phone or to find what`s wrong with MTTY.
Anyone had a similar problem, I mean with MTTY and command error???
yes, i`ve searched trough the posts regarding this problem but I didn`t find any saying that MTTY gave this error.
any idea?
THX in advance!
Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061
Martinhdk said:
Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061
Click to expand...
Click to collapse
if you`re reffering to my problem-how can I copy the JumpSPL1.56-KAIS.exe file and execute it from the phone if I can`t boot it normaly,it always stays in tri-color boot screen?
actually, I`ve bricked my phone with that HardSPL procedure.It was the first step for unlocking. I`ve copied the JumpSPL1.56-KAIS.exe file, executed it and then rebooted and tried to flash with the modified ROM from the jockyw2001`s unlocker. it stopped at 95% and now it seems that it is still CID locked and bricked in boot mode. i`ve already said what MTTY gives as an error.
any idea what may be the problem?
like always:the problem is in RTFM
while i was working on my Kaiser i was doing lots of other things on other computers so i`ve skipped the step with flashing the HardSPL,that`s why all went wrong now,as i`m at home i have more time to read the posts and i`ll try with the jockyw2001`s procedure from the MTTY, with the task8 command.
hope it will help,unless the only solution is to dump the same ROM....
i`ll higly apreciate if anyone has a different solution....
will post results
The problem is that I can't flash the phone with anything be that HardSPL or the original Orange ROM or whatever you care to mention because the PC can't communicate with the device via the USB cable after Activesync ceases to operate. As such everything works up until the % progress bars come on both screens and then they stay at 0% before the communication error message appears.
Funny thing is that the phone is communicating with the PC as USB/Serial alternate depending on whether the cable is plugged in or not and the PC recognises the USB device when its plugged in and when Activesync isn't controlling the situation.
I've been stuck like this with a Hermes but not the Kaiser (yet). As far as I'm aware, you don't need activesync running to run a rom upgrade. If you are in bootloader mode (tricolour screen) you can run the upgrade directly with activesync not connected. If hardspl isn't installed then you should flash the original rom, and if you're unlocked then any rom should do.
Also it might be worth trying the SD card method for flashing. But either way I'd use the original rom and then when you get the phone working again keep trying with HardSPL until it's successful - don't flash any other roms without it.
Laubscherc said:
I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/
Click to expand...
Click to collapse
Thanks for your help.
I did try other "original" rom I got in here http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
The version corresponding my rom is (1.57.502.2 (radio 1.27.12.11)), however I got the error code 294 Invalid Vendor ID after 1%.
I did try the ftp address you mentioned, but I can't login neither anonymously nor with user & psw for xda-developers.
I would like to try the rom you are referring to, please give me another link to download the file.
Best Regards.
Martinhdk said:
http://forum.xda-developers.com/sho...ardware devices list.
Thanks for your help.:)
Click to expand...
Click to collapse
Stuck in Tri color screen
I have been fighting the same issue for several days. Radio gets to 95% and errors. Then hung up in tri color screen. I used MTTY - "set 14 0" command then "boot" command inMTTY to get the phone to boot. I have had to do this a number of times, sometimes more than once per incident. Hope it works for you too. P.S. once you have a successful flash the phone returns to normal operation until then it will go back to tri color screen on reset. I just flashed a startup splash screen to get mine back to normal.
pennco can you expand in further detail on what you actually did with MTTY cause I have the EXACT same problem....
Hi everyone,
Yesterday I tried to update my HTC Wizard through Windows Update.
After the update was downloaded and installed it had to reboot.
But when the Windows Mobile screen appears, it gives me a "device authentication failure, Please contact the product manufacter. For reference, please provide your device ID.
Then a long serial of numbers.."
I tried to do a hard reset, but no result.
Is there a solution for this problem?
Regards and TIA
Rindert
never used windows update on the phone itself before so cant explain why that happened.
What rom are you using is it stock or one of the 6 or 6.1 builds.
might be worth flashing back to a stock rom if you can get into the tricolor boot loader mode as it doesnt sound bricked which would reset everything.
can you get into the phone with activesync to get at the files on the phone?
Windows Update actually WORKED for you? I have never even heard of an update being released via Windows Update on WinMo....are you sure thats what you did?
@ Funy
I have a MDA Vario, originally with WM5, but I've upgraded it to
WM6.
But never updated it to 6.1.
The problem is, I can't get into my phone through ActiveSync.
It freezes when the error appears.
Is there another way to get into the tricolor bootloader without ActiveSync?
@ ashashaur
Yeah, it did.
First the wizard (not the phone) checked for available updates.
There was a update available, so I tried to update it.
First he downloaded it, restart, and installed it.
When it was done, the phone had to restart, and after that, the problem occured.
note: I'm from the netherlands, so the grammar might be a bit strange...
Man, that is roayally wierd...as soon as I read this today, I hit me own phone upto the Windows Update page, and it promptly returned saying that there are no updates availible...I just dunno what to tell you...have you tried forcing your phone into bootloader mode?
rindert said:
@ Funy
I have a MDA Vario, originally with WM5, but I've upgraded it to
WM6.
But never updated it to 6.1.
The problem is, I can't get into my phone through ActiveSync.
It freezes when the error appears.
Is there another way to get into the tricolor bootloader without ActiveSync?
@ ashashaur
Yeah, it did.
First the wizard (not the phone) checked for available updates.
There was a update available, so I tried to update it.
First he downloaded it, restart, and installed it.
When it was done, the phone had to restart, and after that, the problem occured.
note: I'm from the netherlands, so the grammar might be a bit strange...
Click to expand...
Click to collapse
Boatloader: Hold Camera button and press Power button. Wait and a nice tri color boot screen will appear.
yayayay!!!
I fixed it
Thx for all your help and support!!
I really appreciate it
Rindert
glad you got it fixed. what was the fix in the end?
I was able to get into the bootloader, so I could flash it again.
And it works
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
bsgbelg said:
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
Click to expand...
Click to collapse
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Not possible to flash anything
what I've tried so far:
- activate active sync to install hardSPL. Not working
- install HardSPL through microSD. Not working
- install ROM through SD. Not working
I tried a non HCSD for a change, and then I see the loading scree flashing up, but quickly says No rom found and returns to the bootloader screen.
The only thing that works is load the bootloader (red green blue white) into a screen that says:
KAIS130
SPL-3.29.0000
CPLD-8
Serial
When connected to USB, it says USB, but no disk is showing in Explorer or any connection is made to AS
The only thing I've done in the past is flash the 6.1 rom through the system provided by HTC with a file called RUU_Kaiser_HTC_NLD_3.29.404.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
Please help, I really like this phone and hate to loose it
put it into bootloader, connect it to the computer and then flash one of the htc roms. make sure its an htc rom, you cant flash a custom rom cause you dont have hardspl
I have not been able to find the original rom, only the exe from htc which says Connect with active sync. Do I have to set it in bootloader and then execute the program?
Solved
Just want to let you know I sorted it out!
Flashing the original rom does not need active sync, the bootloader USB connection is sufficient.
After this, the phone restarted in 'Erasing memory' mode, but was able to finish it and reinstall the whole rom.
I believe I got the taste of it and will start testing some other roms...
msd24200 said:
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Click to expand...
Click to collapse
Thanks, worked fine
majedaly said:
Thanks, worked fine
Click to expand...
Click to collapse
good to know